According to the Zynq TRM, gigabit half duplex is not supported.  Add a
new cap and compatible string so Zynq can avoid advertising that mode.

Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The tx_curr_frame_payload field is u32. When we try to calculate a
small negative delta based on it, we end up with a positive integer
close to 2^32 instead.  So the tx_bytes pointer increases by about
2^32 for every transmitted frame.

Fix by calculating the delta as a signed long.

Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Reported-by: Florian Bruhin <me@the-compiler.org>
Fixes: 7a1e890e2168 ("usbnet: Fix tx_bytes statistic running backward in cdc_ncm")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is an alternative way of fixing:
 commit db9683fb412d ("net: phy: Make sure PHY_RESUMING state change
                      is always processed")

When the PHY state transitions from PHY_HALTED to PHY_RESUMING, there are
two things we need to do:
1). Re-enable interrupts (and power up the physical link, if powered down)
2). Update the PHY state and net-device based on the link status.

There's no strict reason why #1 has to be done from within the main
phy_state_machine() function. There is a risk that other changes to the
PHY (e.g. setting speed/duplex, which calls phy_start_aneg()) could cause
a subsequent state transition before phy_state_machine() has processed
the PHY_RESUMING state change. This would leave the PHY with interrupts
disabled and/or still in the BMCR_PDOWN/low-power mode.

Moving enabling the interrupts and phy_resume() into phy_start() will
guarantee this work always gets done. As the PHY is already in the HALTED
state and interrupts are disabled, it shouldn't conflict with any work
being done in phy_state_machine(). The downside of this change is that if
the PHY_RESUMING state is ever entered from anywhere else, it'll also have
to repeat this work.

Signed-off-by: Tim Beale <tim.beale@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>

By inspection, this appears to be a typo.  The gating comparison
involves vxlan->dev rather than dev.  In fact, dev is the iterator in
the preceding loop above but it is actually constant in the 2nd loop.

Use of dev seems to be a bad cut-n-paste from the prior call to
unregister_netdevice_queue.  Change dev to vxlan->dev, since that is
what is actually being checked.

Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Before the patch, the command 'ip link add bond2 type bond mode 802.3ad'
causes the kernel to send a rtnl message for the bond2 interface, with an
ifindex 0.

'ip monitor' shows:
0: bond2: <BROADCAST,MULTICAST,MASTER> mtu 1500 state DOWN group default
    link/ether 00:00:00:00:00:00 brd ff:ff:ff:ff:ff:ff
9: bond2@NONE: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noop state DOWN group default
    link/ether ea:3e:1f:53:92:7b brd ff:ff:ff:ff:ff:ff
[snip]

The patch fixes the spotted bug by checking in bond driver if the interface
is registered before calling the notifier chain.
It also adds a check in rtmsg_ifinfo() to prevent this kind of bug in the
future.

Fixes: d4261e565000 ("bonding: create netlink event when bonding option is changed")
CC: Jiri Pirko <jiri@resnulli.us>
Reported-by: Julien Meunier <julien.meunier@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If phy_start_aneg() was called while the phydev is in the PHY_RESUMING
state, then its state would immediately transition to PHY_AN (or
PHY_FORCING). This meant the phy_state_machine() never processed the
PHY_RESUMING state change, which meant interrupts weren't enabled for the
PHY. If the PHY used low-power mode (i.e. using BMCR_PDOWN), then the
physical link wouldn't get powered up again.

There seems no point for phy_start_aneg() to make the PHY_RESUMING -->
PHY_AN transition, as the state machine will do this anyway. I'm not sure
about the case where autoneg is disabled, as my patch will change
behaviour so that the PHY goes to PHY_NOLINK instead of PHY_FORCING. An
alternative solution would be to move the phy_config_interrupt() and
phy_resume() work out of the state machine and into phy_start().

The background behind this: we're running linux v3.16.7 and from user-space
we want to enable the eth port (i.e. do a SIOCSIFFLAGS ioctl with the
IFF_UP flag) and immediately afterward set the interface's speed/duplex.
Enabling the interface calls .ndo_open() then phy_start() and the PHY
transitions PHY_HALTED --> PHY_RESUMING. Setting the speed/duplex ends up
calling phy_ethtool_sset(), which calls phy_start_aneg() (meanwhile the
phy_state_machine() hasn't processed the PHY_RESUMING state change yet).

Signed-off-by: Tim Beale <tim.beale@alliedtelesis.co.nz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RGMII interfaces come in multiple flavors: RGMII with transmit or
receive internal delay, no delays at all, or delays in both direction.

This change extends the initial check for PHY_INTERFACE_MODE_RGMII to
cover all of these variants since EEE should be allowed for any of these
modes, since it is a property of the RGMII, hence Gigabit PHY capability
more than the RGMII electrical interface and its delays.

Fixes: a59a4d192166 ("phy: add the EEE support and the way to access to the MMD registers")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Once we get a neighbour through looking up arp cache or creating a
new one in rocker_port_ipv4_resolve(), the neighbour's refcount is
already taken. But as we don't put the refcount again after it's
used, this makes the neighbour entry leaked.

Suggested-by: Eric Dumazet <edumazet@google.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

Describe the handler for RXUBR better with a new comment.

Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Reviewied-by: Josh Cartwright <joshc@ni.com>
Reviewied-by: Ben Shelton <ben.shelton@ni.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With a cross-compiler based on gcc-4.9, I see warnings like the following:

  drivers/net/ethernet/mellanox/mlx4/resource_tracker.c: In function 'mlx4_SW2HW_CQ_wrapper':
  drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:3048:10: error: 'cq' may be used uninitialized in this function [-Werror=maybe-uninitialized]
    cq->mtt = mtt;

I think the warning is spurious because we only use cq when
cq_res_start_move_to() returns zero, and it always initializes *cq in that
case.  The srq case is similar.  But maybe gcc isn't smart enough to figure
that out.

Initialize cq and srq explicitly to avoid the warnings.

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>