The netif_wake_queue() is called correctly (i.e. only on !txfull condition) from txdone routine. So Unconditional call to the netif_wake_queue() here is wrong. This might cause calling of start_xmit routine on txfull state and trigger BUG_ON. This bug does not happen when NAPI disabled. After txdone there must be at least one free tx slot. But with NAPI, this is not true anymore and the BUG_ON can hits on heavy load. In this driver NAPI was enabled on 2.6.33-rc1 so this is regression from 2.6.32 kernel. Reported-by: Ralf Roesch <ralf.roesch@rw-gmbh.de> Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new vid/pid to the cdc_ether whitelist. Device added: - Ericsson Mobile Broadband variant C3607w Signed-off-by: Torgny Johansson <torgny.johansson@gmail.com> -- To unsubscribe from this list: send the line "unsubscribe netdev" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Signed-off-by: David S. Miller <davem@davemloft.net>
Check for error return from pci_map_single/pci_map_page and clean up. With this and the previous patch the driver was able to handle a significant percentage of errors (I set the fault injection rate to 10% and could still download large files at a reasonable speed). Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Check the frame control for ieee80211_is_data_qos() is true before counting the number of tfds can be free, the tfds_in_queue only increment when ieee80211_is_data_qos() is true before transmit; so it should only decrement if the type match. Remove ieee80211_is_data_qos check for frame_ctrl in tx_resp to avoid invalid information pass from uCode. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> CC: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
When receive reply_tx and ready to decrement the count for number of tfds in queue, do error checking to prevent error condition and tfds_in_queue become negative number. Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> CC: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
The temperature and voltage limits currently set on these boards are too conservative and will cause the driver to stop the net device erroneously in some systems. Based on a review of the chip datasheets and advice from the designer of these boards: - Raise the maximum board temperatures to the specified maximum ambient temperatures for their PHYs plus the expected temperature bias of the board - Raise the maximum controller temperature to 90 degrees - Lower the minimum temperatures to 0 degrees - Widen the voltage tolerances to at least +/- 10% Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
efx_mcdi_poll() uses positive error numbers, matching the MCDI protocol. It must negate the result of efx_mcdi_poll_reboot() which returns the usual negative error numbers. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The HT extension channel settings require priv->staging_rxon.channel to be accurate. However, iwl_set_rxon_ht was being called before iwl_set_rxon_channel and thus HT40 could be broken unless another call to iwl_mac_config came in. This problem was recently introduced by "iwlwifi: Fix to set correct ht configuration" The particular setting in which I noticed this was monitor mode: iwconfig wlan0 mode monitor ifconfig wlan0 up ./iw wlan0 set channel 64 HT40- #./iw wlan0 set channel 64 HT40- tcpdump -i wlan0 -y IEEE802_11_RADIO would only catch HT40 packets if I issued the IW command twice. From visual inspection, iwl_set_rxon_channel does not depend on iwl_set_rxon_ht, so simply swapping them should be safe and fixes this problem. Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu> Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> CC: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before sending a command to the ASIC, set version properly. This is necessary for the ARM firmware to send correct data to the driver. This also fixes a bug in certain skews of the ASIC where the statistics are misreported. Signed-off-by: Ajit Khaparde <ajitk@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>