Kalle Valo says: ==================== wireless-drivers fixes for 5.1 Second set of fixes for 5.1. iwlwifi * add some new PCI IDs (plus a struct name change they depend on) * fix crypto with new devices, namely 22560 and above * fix for a potential deadlock in the TX path * a fix for offloaded rate-control * support new PCI HW IDs which use a new FW mt76 * fix lock initialisation and a possible deadlock * aggregation fixes rt2x00 * fix sequence numbering during retransmits ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
Second batch of iwlwifi fixes intended for v5.1 * fix for a potential deadlock in the TX path; * a fix for offloaded rate-control; * support new PCI HW IDs which use a new FW;
Move ieee80211_tx_status_ext() outside of status_list lock section
in order to avoid locking dependency and possible deadlock reposed by
LOCKDEP in below warning.
Also do mt76_tx_status_lock() just before it's needed.
[ 440.224832] WARNING: possible circular locking dependency detected
[ 440.224833] 5.1.0-rc2+ #22 Not tainted
[ 440.224834] ------------------------------------------------------
[ 440.224835] kworker/u16:28/2362 is trying to acquire lock:
[ 440.224836] 0000000089b8cacf (&(&q->lock)->rlock#2){+.-.}, at: mt76_wake_tx_queue+0x4c/0xb0 [mt76]
[ 440.224842]
but task is already holding lock:
[ 440.224842] 000000002cfedc59 (&(&sta->lock)->rlock){+.-.}, at: ieee80211_stop_tx_ba_cb+0x32/0x1f0 [mac80211]
[ 440.224863]
which lock already depends on the new lock.
[ 440.224863]
the existing dependency chain (in reverse order) is:
[ 440.224864]
-> #3 (&(&sta->lock)->rlock){+.-.}:
[ 440.224869] _raw_spin_lock_bh+0x34/0x40
[ 440.224880] ieee80211_start_tx_ba_session+0xe4/0x3d0 [mac80211]
[ 440.224894] minstrel_ht_get_rate+0x45c/0x510 [mac80211]
[ 440.224906] rate_control_get_rate+0xc1/0x140 [mac80211]
[ 440.224918] ieee80211_tx_h_rate_ctrl+0x195/0x3c0 [mac80211]
[ 440.224930] ieee80211_xmit_fast+0x26d/0xa50 [mac80211]
[ 440.224942] __ieee80211_subif_start_xmit+0xfc/0x310 [mac80211]
[ 440.224954] ieee80211_subif_start_xmit+0x38/0x390 [mac80211]
[ 440.224956] dev_hard_start_xmit+0xb8/0x300
[ 440.224957] __dev_queue_xmit+0x7d4/0xbb0
[ 440.224968] ip6_finish_output2+0x246/0x860 [ipv6]
[ 440.224978] mld_sendpack+0x1bd/0x360 [ipv6]
[ 440.224987] mld_ifc_timer_expire+0x1a4/0x2f0 [ipv6]
[ 440.224989] call_timer_fn+0x89/0x2a0
[ 440.224990] run_timer_softirq+0x1bd/0x4d0
[ 440.224992] __do_softirq+0xdb/0x47c
[ 440.224994] irq_exit+0xfa/0x100
[ 440.224996] smp_apic_timer_interrupt+0x9a/0x220
[ 440.224997] apic_timer_interrupt+0xf/0x20
[ 440.224999] cpuidle_enter_state+0xc1/0x470
[ 440.225000] do_idle+0x21a/0x260
[ 440.225001] cpu_startup_entry+0x19/0x20
[ 440.225004] start_secondary+0x135/0x170
[ 440.225006] secondary_startup_64+0xa4/0xb0
[ 440.225007]
-> #2 (&(&sta->rate_ctrl_lock)->rlock){+.-.}:
[ 440.225009] _raw_spin_lock_bh+0x34/0x40
[ 440.225022] rate_control_tx_status+0x4f/0xb0 [mac80211]
[ 440.225031] ieee80211_tx_status_ext+0x142/0x1a0 [mac80211]
[ 440.225035] mt76x02_send_tx_status+0x2e4/0x340 [mt76x02_lib]
[ 440.225037] mt76x02_tx_status_data+0x31/0x40 [mt76x02_lib]
[ 440.225040] mt76u_tx_status_data+0x51/0xa0 [mt76_usb]
[ 440.225042] process_one_work+0x237/0x5d0
[ 440.225043] worker_thread+0x3c/0x390
[ 440.225045] kthread+0x11d/0x140
[ 440.225046] ret_from_fork+0x3a/0x50
[ 440.225047]
-> #1 (&(&list->lock)->rlock#8){+.-.}:
[ 440.225049] _raw_spin_lock_bh+0x34/0x40
[ 440.225052] mt76_tx_status_skb_add+0x51/0x100 [mt76]
[ 440.225054] mt76x02u_tx_prepare_skb+0xbd/0x116 [mt76x02_usb]
[ 440.225056] mt76u_tx_queue_skb+0x5f/0x180 [mt76_usb]
[ 440.225058] mt76_tx+0x93/0x190 [mt76]
[ 440.225070] ieee80211_tx_frags+0x148/0x210 [mac80211]
[ 440.225081] __ieee80211_tx+0x75/0x1b0 [mac80211]
[ 440.225092] ieee80211_tx+0xde/0x110 [mac80211]
[ 440.225105] __ieee80211_tx_skb_tid_band+0x72/0x90 [mac80211]
[ 440.225122] ieee80211_send_auth+0x1f3/0x360 [mac80211]
[ 440.225141] ieee80211_auth.cold.40+0x6c/0x100 [mac80211]
[ 440.225156] ieee80211_mgd_auth.cold.50+0x132/0x15f [mac80211]
[ 440.225171] cfg80211_mlme_auth+0x149/0x360 [cfg80211]
[ 440.225181] nl80211_authenticate+0x273/0x2e0 [cfg80211]
[ 440.225183] genl_family_rcv_msg+0x196/0x3a0
[ 440.225184] genl_rcv_msg+0x47/0x8e
[ 440.225185] netlink_rcv_skb+0x3a/0xf0
[ 440.225187] genl_rcv+0x24/0x40
[ 440.225188] netlink_unicast+0x16d/0x210
[ 440.225189] netlink_sendmsg+0x204/0x3b0
[ 440.225191] sock_sendmsg+0x36/0x40
[ 440.225193] ___sys_sendmsg+0x259/0x2b0
[ 440.225194] __sys_sendmsg+0x47/0x80
[ 440.225196] do_syscall_64+0x60/0x1f0
[ 440.225197] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 440.225198]
-> #0 (&(&q->lock)->rlock#2){+.-.}:
[ 440.225200] lock_acquire+0xb9/0x1a0
[ 440.225202] _raw_spin_lock_bh+0x34/0x40
[ 440.225204] mt76_wake_tx_queue+0x4c/0xb0 [mt76]
[ 440.225215] ieee80211_agg_start_txq+0xe8/0x2b0 [mac80211]
[ 440.225225] ieee80211_stop_tx_ba_cb+0xb8/0x1f0 [mac80211]
[ 440.225235] ieee80211_ba_session_work+0x1c1/0x2f0 [mac80211]
[ 440.225236] process_one_work+0x237/0x5d0
[ 440.225237] worker_thread+0x3c/0x390
[ 440.225239] kthread+0x11d/0x140
[ 440.225240] ret_from_fork+0x3a/0x50
[ 440.225240]
other info that might help us debug this:
[ 440.225241] Chain exists of:
&(&q->lock)->rlock#2 --> &(&sta->rate_ctrl_lock)->rlock --> &(&sta->lock)->rlock
[ 440.225243] Possible unsafe locking scenario:
[ 440.225244] CPU0 CPU1
[ 440.225244] ---- ----
[ 440.225245] lock(&(&sta->lock)->rlock);
[ 440.225245] lock(&(&sta->rate_ctrl_lock)->rlock);
[ 440.225246] lock(&(&sta->lock)->rlock);
[ 440.225247] lock(&(&q->lock)->rlock#2);
[ 440.225248]
*** DEADLOCK ***
[ 440.225249] 5 locks held by kworker/u16:28/2362:
[ 440.225250] #0: 0000000048fcd291 ((wq_completion)phy0){+.+.}, at: process_one_work+0x1b5/0x5d0
[ 440.225252] #1: 00000000f1c6828f ((work_completion)(&sta->ampdu_mlme.work)){+.+.}, at: process_one_work+0x1b5/0x5d0
[ 440.225254] #2: 00000000433d2b2c (&sta->ampdu_mlme.mtx){+.+.}, at: ieee80211_ba_session_work+0x5c/0x2f0 [mac80211]
[ 440.225265] #3: 000000002cfedc59 (&(&sta->lock)->rlock){+.-.}, at: ieee80211_stop_tx_ba_cb+0x32/0x1f0 [mac80211]
[ 440.225276] #4: 000000009d7b9a44 (rcu_read_lock){....}, at: ieee80211_agg_start_txq+0x33/0x2b0 [mac80211]
[ 440.225286]
stack backtrace:
[ 440.225288] CPU: 2 PID: 2362 Comm: kworker/u16:28 Not tainted 5.1.0-rc2+ #22
[ 440.225289] Hardware name: LENOVO 20KGS23S0P/20KGS23S0P, BIOS N23ET55W (1.30 ) 08/31/2018
[ 440.225300] Workqueue: phy0 ieee80211_ba_session_work [mac80211]
[ 440.225301] Call Trace:
[ 440.225304] dump_stack+0x85/0xc0
[ 440.225306] print_circular_bug.isra.38.cold.58+0x15c/0x195
[ 440.225307] check_prev_add.constprop.48+0x5f0/0xc00
[ 440.225309] ? check_prev_add.constprop.48+0x39d/0xc00
[ 440.225311] ? __lock_acquire+0x41d/0x1100
[ 440.225312] __lock_acquire+0xd98/0x1100
[ 440.225313] ? __lock_acquire+0x41d/0x1100
[ 440.225315] lock_acquire+0xb9/0x1a0
[ 440.225317] ? mt76_wake_tx_queue+0x4c/0xb0 [mt76]
[ 440.225319] _raw_spin_lock_bh+0x34/0x40
[ 440.225321] ? mt76_wake_tx_queue+0x4c/0xb0 [mt76]
[ 440.225323] mt76_wake_tx_queue+0x4c/0xb0 [mt76]
[ 440.225334] ieee80211_agg_start_txq+0xe8/0x2b0 [mac80211]
[ 440.225344] ieee80211_stop_tx_ba_cb+0xb8/0x1f0 [mac80211]
[ 440.225354] ieee80211_ba_session_work+0x1c1/0x2f0 [mac80211]
[ 440.225356] process_one_work+0x237/0x5d0
[ 440.225358] worker_thread+0x3c/0x390
[ 440.225359] ? wq_calc_node_cpumask+0x70/0x70
[ 440.225360] kthread+0x11d/0x140
[ 440.225362] ? kthread_create_on_node+0x40/0x40
[ 440.225363] ret_from_fork+0x3a/0x50
Cc: stable@vger.kernel.org
Fixes: 88046b2c9f6d ("mt76: add support for reporting tx status with skb")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently rt2x00 devices retransmit the management frames with incremented sequence number if hardware is assigning the sequence. This is HW bug fixed already for non-QOS data frames, but it should be fixed for management frames except beacon. Without fix retransmitted frames have wrong SN: AlphaNet_e8:fb:36 Vivotek_52:31:51 Authentication, SN=1648, FN=0, Flags=........C Frame is not being retransmitted 1648 1 AlphaNet_e8:fb:36 Vivotek_52:31:51 Authentication, SN=1649, FN=0, Flags=....R...C Frame is being retransmitted 1649 1 AlphaNet_e8:fb:36 Vivotek_52:31:51 Authentication, SN=1650, FN=0, Flags=....R...C Frame is being retransmitted 1650 1 With the fix SN stays correctly the same: 88:6a:e3:e8:f9:a2 8c:f5:a3:88:76:87 Authentication, SN=1450, FN=0, Flags=........C 88:6a:e3:e8:f9:a2 8c:f5:a3:88:76:87 Authentication, SN=1450, FN=0, Flags=....R...C 88:6a:e3:e8:f9:a2 8c:f5:a3:88:76:87 Authentication, SN=1450, FN=0, Flags=....R...C Cc: stable@vger.kernel.org Signed-off-by: Vijayakumar Durai <vijayakumar.durai1@vivint.com> [sgruszka: simplify code, change comments and changelog] Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Now that the sequence number allocation is fixed, we can finally send a BAR at powersave wakeup time to refresh the receiver side reorder window Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If the MT_TXD3_SN_VALID flag is not set in the tx descriptor, the hardware assigns the sequence number. However, the rest of the code assumes that the sequence number specified in the 802.11 header gets transmitted. This was causing issues with the aggregation setup, which worked for the initial one (where the sequence numbers were still close), but not for further teardown/re-establishing of sessions. Additionally, the overwrite of the TID sequence number in WTBL2 was resetting the hardware assigned sequence numbers, causing them to drift further apart. Fix this by using the software assigned sequence numbers Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes lockdep complaint and a potential race condition Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently there is no way for the driver to signal to mac80211 that it should
schedule a TXQ even if there are no packets on the mac80211 part of that queue.
This is problematic if the driver has an internal retry queue to deal with
software A-MPDU retry.
This patch changes the behavior of ieee80211_schedule_txq to always schedule
the queue, as its only user (ath9k) seems to expect such behavior already:
it calls this function on tx status and on powersave wakeup whenever its
internal retry queue is not empty.
Also add an extra argument to ieee80211_return_txq to get the same behavior.
This fixes an issue on ath9k where tx queues with packets to retry (and no
new packets in mac80211) would not get serviced.
Fixes: 89cea7493a346 ("ath9k: Switch to mac80211 TXQ scheduling and airtime APIs")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we just set this to 2048, and have multiple limits you
can select from, the total number might run over and cause
a warning in cfg80211. This doesn't make sense, so we just
calculate the total max_interfaces now.
Reported-by: syzbot+8f91bd563bbff230d0ee@syzkaller.appspotmail.com
Fixes: 99e3a44bac37 ("mac80211_hwsim: allow setting iftype support")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a new configuration with a new firmware name for quz devices. And, since these devices have the same PCI device and subsystem IDs, we need to add some code to switch from a normal qu firmware to the quz firmware. Signed-off-by: Luca Coelho <luciano.coelho@intel.com>