linux.git/drivers/net/wireless/intel, branch v6.11-rc2 Linux kernel source tree thermal: core: Allow thermal zones to tell the core to ignore them 2024-07-18T11:35:55+00:00 Rafael J. Wysocki rafael.j.wysocki@intel.com 2024-07-17T19:45:02+00:00 e528be3c87be953b73e7826a2d7e4b837cbad39d The iwlwifi wireless driver registers a thermal zone that is only needed when the network interface handled by it is up and it wants that thermal zone to be effectively ignored by the core otherwise. Before commit a8a261774466 ("thermal: core: Call monitor_thermal_zone() if zone temperature is invalid") that could be achieved by returning an error code from the thermal zone's .get_temp() callback because the core did not really handle errors returned by it almost at all. However, commit a8a261774466 made the core attempt to recover from the situation in which the temperature of a thermal zone cannot be determined due to errors returned by its .get_temp() and is always invalid from the core's perspective. That was done because there are thermal zones in which .get_temp() returns errors to start with due to some difficulties related to the initialization ordering, but then it will start to produce valid temperature values at one point. Unfortunately, the simple approach taken by commit a8a261774466, which is to poll the thermal zone periodically until its .get_temp() callback starts to return valid temperature values, is at odds with the special thermal zone in iwlwifi in which .get_temp() may always return an error because its network interface may always be down. If that happens, every attempt to invoke the thermal zone's .get_temp() callback resulting in an error causes the thermal core to print a dev_warn() message to the kernel log which is super-noisy. To address this problem, make the core handle the case in which .get_temp() returns 0, but the temperature value returned by it is not actually valid, in a special way. Namely, make the core completely ignore the invalid temperature value coming from .get_temp() in that case, which requires folding in update_temperature() into its caller and a few related changes. On the iwlwifi side, modify iwl_mvm_tzone_get_temp() to return 0 and put THERMAL_TEMP_INVALID into the temperature return memory location instead of returning an error when the firmware is not running or it is not of the right type. Also, to clearly separate the handling of invalid temperature values from the thermal zone initialization, introduce a special THERMAL_TEMP_INIT value specifically for the latter purpose. Fixes: a8a261774466 ("thermal: core: Call monitor_thermal_zone() if zone temperature is invalid") Closes: https://lore.kernel.org/linux-pm/20240715044527.GA1544@sol.localdomain/ Reported-by: Eric Biggers <ebiggers@kernel.org> Reported-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> Link: https://bugzilla.kernel.org/show_bug.cgi?id=201761 Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name> Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> Cc: 6.10+ <stable@vger.kernel.org> # 6.10+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Link: https://patch.msgid.link/4950004.31r3eYUQgx@rjwysocki.net [ rjw: Rebased on top of the current mainline ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> 
The iwlwifi wireless driver registers a thermal zone that is only needed
when the network interface handled by it is up and it wants that thermal
zone to be effectively ignored by the core otherwise.

Before commit a8a261774466 ("thermal: core: Call monitor_thermal_zone()
if zone temperature is invalid") that could be achieved by returning
an error code from the thermal zone's .get_temp() callback because the
core did not really handle errors returned by it almost at all.
However, commit a8a261774466 made the core attempt to recover from the
situation in which the temperature of a thermal zone cannot be
determined due to errors returned by its .get_temp() and is always
invalid from the core's perspective.

That was done because there are thermal zones in which .get_temp()
returns errors to start with due to some difficulties related to the
initialization ordering, but then it will start to produce valid
temperature values at one point.

Unfortunately, the simple approach taken by commit a8a261774466,
which is to poll the thermal zone periodically until its .get_temp()
callback starts to return valid temperature values, is at odds with
the special thermal zone in iwlwifi in which .get_temp() may always
return an error because its network interface may always be down.  If
that happens, every attempt to invoke the thermal zone's .get_temp()
callback resulting in an error causes the thermal core to print a
dev_warn() message to the kernel log which is super-noisy.

To address this problem, make the core handle the case in which
.get_temp() returns 0, but the temperature value returned by it
is not actually valid, in a special way.  Namely, make the core
completely ignore the invalid temperature value coming from
.get_temp() in that case, which requires folding in
update_temperature() into its caller and a few related changes.

On the iwlwifi side, modify iwl_mvm_tzone_get_temp() to return 0
and put THERMAL_TEMP_INVALID into the temperature return memory
location instead of returning an error when the firmware is not
running or it is not of the right type.

Also, to clearly separate the handling of invalid temperature
values from the thermal zone initialization, introduce a special
THERMAL_TEMP_INIT value specifically for the latter purpose.

Fixes: a8a261774466 ("thermal: core: Call monitor_thermal_zone() if zone temperature is invalid")
Closes: https://lore.kernel.org/linux-pm/20240715044527.GA1544@sol.localdomain/
Reported-by: Eric Biggers <ebiggers@kernel.org>
Reported-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=201761
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Cc: 6.10+ <stable@vger.kernel.org> # 6.10+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://patch.msgid.link/4950004.31r3eYUQgx@rjwysocki.net
[ rjw: Rebased on top of the current mainline ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Merge tag 'net-next-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next 2024-07-17T02:28:34+00:00 Linus Torvalds torvalds@linux-foundation.org 2024-07-17T02:28:34+00:00 51835949dda3783d4639cfa74ce13a3c9829de00 Pull networking updates from Jakub Kicinski: "Not much excitement - a handful of large patchsets (devmem among them) did not make it in time. Core & protocols: - Use local_lock in addition to local_bh_disable() to protect per-CPU resources in networking, a step closer for local_bh_disable() not to act as a big lock on PREEMPT_RT - Use flex array for netdevice priv area, ensure its cache alignment - Add a sysctl knob to allow user to specify a default rto_min at socket init time. Bit of a big hammer but multiple companies were independently carrying such patch downstream so clearly it's useful - Support scheduling transmission of packets based on CLOCK_TAI - Un-pin TCP TIMEWAIT timer to avoid it firing on CPUs later cordoned off using cpusets - Support multiple L2TPv3 UDP tunnels using the same 5-tuple address - Allow configuration of multipath hash seed, to both allow synchronizing hashing of two routers, and preventing partial accidental sync - Improve TCP compliance with RFC 9293 for simultaneous connect() - Support sending NAT keepalives in IPsec ESP in UDP states. Userspace IKE daemon had to do this before, but the kernel can better keep track of it - Support sending supervision HSR frames with MAC addresses stored in ProxyNodeTable when RedBox (i.e. HSR-SAN) is enabled - Introduce IPPROTO_SMC for selecting SMC when socket is created - Allow UDP GSO transmit from devices with no checksum offload - openvswitch: add packet sampling via psample, separating the sampled traffic from "upcall" packets sent to user space for forwarding - nf_tables: shrink memory consumption for transaction objects Things we sprinkled into general kernel code: - Power Sequencing subsystem (used by Qualcomm Bluetooth driver for QCA6390) [ Already merged separately - Linus ] - Add IRQ information in sysfs for auxiliary bus - Introduce guard definition for local_lock - Add aligned flavor of __cacheline_group_{begin, end}() markings for grouping fields in structures BPF: - Notify user space (via epoll) when a struct_ops object is getting detached/unregistered - Add new kfuncs for a generic, open-coded bits iterator - Enable BPF programs to declare arrays of kptr, bpf_rb_root, and bpf_list_head - Support resilient split BTF which cuts down on duplication and makes BTF as compact as possible WRT BTF from modules - Add support for dumping kfunc prototypes from BTF which enables both detecting as well as dumping compilable prototypes for kfuncs - riscv64 BPF JIT improvements in particular to add 12-argument support for BPF trampolines and to utilize bpf_prog_pack for the latter - Add the capability to offload the netfilter flowtable in XDP layer through kfuncs Driver API: - Allow users to configure IRQ tresholds between which automatic IRQ moderation can choose - Expand Power Sourcing (PoE) status with power, class and failure reason. Support setting power limits - Track additional RSS contexts in the core, make sure configuration changes don't break them - Support IPsec crypto offload for IPv6 ESP and IPv4 UDP-encapsulated ESP data paths - Support updating firmware on SFP modules Tests and tooling: - mptcp: use net/lib.sh to manage netns - TCP-AO and TCP-MD5: replace debug prints used by tests with tracepoints - openvswitch: make test self-contained (don't depend on OvS CLI tools) Drivers: - Ethernet high-speed NICs: - Broadcom (bnxt): - increase the max total outstanding PTP TX packets to 4 - add timestamping statistics support - implement netdev_queue_mgmt_ops - support new RSS context API - Intel (100G, ice, idpf): - implement FEC statistics and dumping signal quality indicators - support E825C products (with 56Gbps PHYs) - nVidia/Mellanox: - support HW-GRO - mlx4/mlx5: support per-queue statistics via netlink - obey the max number of EQs setting in sub-functions - AMD/Solarflare: - support new RSS context API - AMD/Pensando: - ionic: rework fix for doorbell miss to lower overhead and skip it on new HW - Wangxun: - txgbe: support Flow Director perfect filters - Ethernet NICs consumer, embedded and virtual: - Add driver for Tehuti Networks TN40xx chips - Add driver for Meta's internal NIC chips - Add driver for Ethernet MAC on Airoha EN7581 SoCs - Add driver for Renesas Ethernet-TSN devices - Google cloud vNIC: - flow steering support - Microsoft vNIC: - support page sizes other than 4KB on ARM64 - vmware vNIC: - support latency measurement (update to version 9) - VirtIO net: - support for Byte Queue Limits - support configuring thresholds for automatic IRQ moderation - support for AF_XDP Rx zero-copy - Synopsys (stmmac): - support for STM32MP13 SoC - let platforms select the right PCS implementation - TI: - icssg-prueth: add multicast filtering support - icssg-prueth: enable PTP timestamping and PPS - Renesas: - ravb: improve Rx performance 30-400% by using page pool, theaded NAPI and timer-based IRQ coalescing - ravb: add MII support for R-Car V4M - Cadence (macb): - macb: add ARP support to Wake-On-LAN - Cortina: - use phylib for RX and TX pause configuration - Ethernet switches: - nVidia/Mellanox: - support configuration of multipath hash seed - report more accurate max MTU - use page_pool to improve Rx performance - MediaTek: - mt7530: add support for bridge port isolation - Qualcomm: - qca8k: add support for bridge port isolation - Microchip: - lan9371/2: add 100BaseTX PHY support - NXP: - vsc73xx: implement VLAN operations - Ethernet PHYs: - aquantia: enable support for aqr115c - aquantia: add support for PHY LEDs - realtek: add support for rtl8224 2.5Gbps PHY - xpcs: add memory-mapped device support - add BroadR-Reach link mode and support in Broadcom's PHY driver - CAN: - add document for ISO 15765-2 protocol support - mcp251xfd: workaround for erratum DS80000789E, use timestamps to catch when device returns incorrect FIFO status - WiFi: - mac80211/cfg80211: - parse Transmit Power Envelope (TPE) data in mac80211 instead of in drivers - improvements for 6 GHz regulatory flexibility - multi-link improvements - support multiple radios per wiphy - remove DEAUTH_NEED_MGD_TX_PREP flag - Intel (iwlwifi): - bump FW API to 91 for BZ/SC devices - report 64-bit radiotap timestamp - enable P2P low latency by default - handle Transmit Power Envelope (TPE) advertised by AP - remove support for older FW for new devices - fast resume (keeping the device configured) - mvm: re-enable Multi-Link Operation (MLO) - aggregation (A-MSDU) optimizations - MediaTek (mt76): - mt7925 Multi-Link Operation (MLO) support - Qualcomm (ath10k): - LED support for various chipsets - Qualcomm (ath12k): - remove unsupported Tx monitor handling - support channel 2 in 6 GHz band - support Spatial Multiplexing Power Save (SMPS) in 6 GHz band - supprt multiple BSSID (MBSSID) and Enhanced Multi-BSSID Advertisements (EMA) - support dynamic VLAN - add panic handler for resetting the firmware state - DebugFS support for datapath statistics - WCN7850: support for Wake on WLAN - Microchip (wilc1000): - read MAC address during probe to make it visible to user space - suspend/resume improvements - TI (wl18xx): - support newer firmware versions - RealTek (rtw89): - preparation for RTL8852BE-VT support - Wake on WLAN support for WiFi 6 chips - 36-bit PCI DMA support - RealTek (rtlwifi): - RTL8192DU support - Broadcom (brcmfmac): - Management Frame Protection support (to enable WPA3) - Bluetooth: - qualcomm: use the power sequencer for QCA6390 - btusb: mediatek: add ISO data transmission functions - hci_bcm4377: add BCM4388 support - btintel: add support for BlazarU core - btintel: add support for Whale Peak2 - btnxpuart: add support for AW693 A1 chipset - btnxpuart: add support for IW615 chipset - btusb: add Realtek RTL8852BE support ID 0x13d3:0x3591" * tag 'net-next-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1589 commits) eth: fbnic: Fix spelling mistake "tiggerring" -> "triggering" tcp: Replace strncpy() with strscpy() wifi: ath12k: fix build vs old compiler tcp: Don't access uninit tcp_rsk(req)->ao_keyid in tcp_create_openreq_child(). eth: fbnic: Write the TCAM tables used for RSS control and Rx to host eth: fbnic: Add L2 address programming eth: fbnic: Add basic Rx handling eth: fbnic: Add basic Tx handling eth: fbnic: Add link detection eth: fbnic: Add initial messaging to notify FW of our presence eth: fbnic: Implement Rx queue alloc/start/stop/free eth: fbnic: Implement Tx queue alloc/start/stop/free eth: fbnic: Allocate a netdevice and napi vectors with queues eth: fbnic: Add FW communication mechanism eth: fbnic: Add message parsing for FW messages eth: fbnic: Add register init to set PCIe/Ethernet device config eth: fbnic: Allocate core device specific structures and devlink interface eth: fbnic: Add scaffolding for Meta's NIC driver PCI: Add Meta Platforms vendor ID net/sched: cls_flower: propagate tca[TCA_OPTIONS] to NL_REQ_ATTR_CHECK ... 
Pull networking updates from Jakub Kicinski:
 "Not much excitement - a handful of large patchsets (devmem among them)
  did not make it in time.

  Core & protocols:

   - Use local_lock in addition to local_bh_disable() to protect per-CPU
     resources in networking, a step closer for local_bh_disable() not
     to act as a big lock on PREEMPT_RT

   - Use flex array for netdevice priv area, ensure its cache alignment

   - Add a sysctl knob to allow user to specify a default rto_min at
     socket init time. Bit of a big hammer but multiple companies were
     independently carrying such patch downstream so clearly it's useful

   - Support scheduling transmission of packets based on CLOCK_TAI

   - Un-pin TCP TIMEWAIT timer to avoid it firing on CPUs later cordoned
     off using cpusets

   - Support multiple L2TPv3 UDP tunnels using the same 5-tuple address

   - Allow configuration of multipath hash seed, to both allow
     synchronizing hashing of two routers, and preventing partial
     accidental sync

   - Improve TCP compliance with RFC 9293 for simultaneous connect()

   - Support sending NAT keepalives in IPsec ESP in UDP states.
     Userspace IKE daemon had to do this before, but the kernel can
     better keep track of it

   - Support sending supervision HSR frames with MAC addresses stored in
     ProxyNodeTable when RedBox (i.e. HSR-SAN) is enabled

   - Introduce IPPROTO_SMC for selecting SMC when socket is created

   - Allow UDP GSO transmit from devices with no checksum offload

   - openvswitch: add packet sampling via psample, separating the
     sampled traffic from "upcall" packets sent to user space for
     forwarding

   - nf_tables: shrink memory consumption for transaction objects

  Things we sprinkled into general kernel code:

   - Power Sequencing subsystem (used by Qualcomm Bluetooth driver for
     QCA6390)           [ Already merged separately - Linus ]

   - Add IRQ information in sysfs for auxiliary bus

   - Introduce guard definition for local_lock

   - Add aligned flavor of __cacheline_group_{begin, end}() markings for
     grouping fields in structures

  BPF:

   - Notify user space (via epoll) when a struct_ops object is getting
     detached/unregistered

   - Add new kfuncs for a generic, open-coded bits iterator

   - Enable BPF programs to declare arrays of kptr, bpf_rb_root, and
     bpf_list_head

   - Support resilient split BTF which cuts down on duplication and
     makes BTF as compact as possible WRT BTF from modules

   - Add support for dumping kfunc prototypes from BTF which enables
     both detecting as well as dumping compilable prototypes for kfuncs

   - riscv64 BPF JIT improvements in particular to add 12-argument
     support for BPF trampolines and to utilize bpf_prog_pack for the
     latter

   - Add the capability to offload the netfilter flowtable in XDP layer
     through kfuncs

  Driver API:

   - Allow users to configure IRQ tresholds between which automatic IRQ
     moderation can choose

   - Expand Power Sourcing (PoE) status with power, class and failure
     reason. Support setting power limits

   - Track additional RSS contexts in the core, make sure configuration
     changes don't break them

   - Support IPsec crypto offload for IPv6 ESP and IPv4 UDP-encapsulated
     ESP data paths

   - Support updating firmware on SFP modules

  Tests and tooling:

   - mptcp: use net/lib.sh to manage netns

   - TCP-AO and TCP-MD5: replace debug prints used by tests with
     tracepoints

   - openvswitch: make test self-contained (don't depend on OvS CLI
     tools)

  Drivers:

   - Ethernet high-speed NICs:
      - Broadcom (bnxt):
         - increase the max total outstanding PTP TX packets to 4
         - add timestamping statistics support
         - implement netdev_queue_mgmt_ops
         - support new RSS context API
      - Intel (100G, ice, idpf):
         - implement FEC statistics and dumping signal quality indicators
         - support E825C products (with 56Gbps PHYs)
      - nVidia/Mellanox:
         - support HW-GRO
         - mlx4/mlx5: support per-queue statistics via netlink
         - obey the max number of EQs setting in sub-functions
      - AMD/Solarflare:
         - support new RSS context API
      - AMD/Pensando:
         - ionic: rework fix for doorbell miss to lower overhead and
           skip it on new HW
      - Wangxun:
         - txgbe: support Flow Director perfect filters

   - Ethernet NICs consumer, embedded and virtual:
      - Add driver for Tehuti Networks TN40xx chips
      - Add driver for Meta's internal NIC chips
      - Add driver for Ethernet MAC on Airoha EN7581 SoCs
      - Add driver for Renesas Ethernet-TSN devices
      - Google cloud vNIC:
         - flow steering support
      - Microsoft vNIC:
         - support page sizes other than 4KB on ARM64
      - vmware vNIC:
         - support latency measurement (update to version 9)
      - VirtIO net:
         - support for Byte Queue Limits
         - support configuring thresholds for automatic IRQ moderation
         - support for AF_XDP Rx zero-copy
      - Synopsys (stmmac):
         - support for STM32MP13 SoC
         - let platforms select the right PCS implementation
      - TI:
         - icssg-prueth: add multicast filtering support
         - icssg-prueth: enable PTP timestamping and PPS
      - Renesas:
         - ravb: improve Rx performance 30-400% by using page pool,
           theaded NAPI and timer-based IRQ coalescing
         - ravb: add MII support for R-Car V4M
      - Cadence (macb):
         - macb: add ARP support to Wake-On-LAN
      - Cortina:
         - use phylib for RX and TX pause configuration

   - Ethernet switches:
      - nVidia/Mellanox:
         - support configuration of multipath hash seed
         - report more accurate max MTU
         - use page_pool to improve Rx performance
      - MediaTek:
         - mt7530: add support for bridge port isolation
      - Qualcomm:
         - qca8k: add support for bridge port isolation
      - Microchip:
         - lan9371/2: add 100BaseTX PHY support
      - NXP:
         - vsc73xx: implement VLAN operations

   - Ethernet PHYs:
      - aquantia: enable support for aqr115c
      - aquantia: add support for PHY LEDs
      - realtek: add support for rtl8224 2.5Gbps PHY
      - xpcs: add memory-mapped device support
      - add BroadR-Reach link mode and support in Broadcom's PHY driver

   - CAN:
      - add document for ISO 15765-2 protocol support
      - mcp251xfd: workaround for erratum DS80000789E, use timestamps to
        catch when device returns incorrect FIFO status

   - WiFi:
      - mac80211/cfg80211:
         - parse Transmit Power Envelope (TPE) data in mac80211 instead
           of in drivers
         - improvements for 6 GHz regulatory flexibility
         - multi-link improvements
         - support multiple radios per wiphy
         - remove DEAUTH_NEED_MGD_TX_PREP flag
      - Intel (iwlwifi):
         - bump FW API to 91 for BZ/SC devices
         - report 64-bit radiotap timestamp
         - enable P2P low latency by default
         - handle Transmit Power Envelope (TPE) advertised by AP
         - remove support for older FW for new devices
         - fast resume (keeping the device configured)
         - mvm: re-enable Multi-Link Operation (MLO)
         - aggregation (A-MSDU) optimizations
      - MediaTek (mt76):
         - mt7925 Multi-Link Operation (MLO) support
      - Qualcomm (ath10k):
         - LED support for various chipsets
      - Qualcomm (ath12k):
         - remove unsupported Tx monitor handling
         - support channel 2 in 6 GHz band
         - support Spatial Multiplexing Power Save (SMPS) in 6 GHz band
         - supprt multiple BSSID (MBSSID) and Enhanced Multi-BSSID
           Advertisements (EMA)
         - support dynamic VLAN
         - add panic handler for resetting the firmware state
         - DebugFS support for datapath statistics
         - WCN7850: support for Wake on WLAN
      - Microchip (wilc1000):
         - read MAC address during probe to make it visible to user space
         - suspend/resume improvements
      - TI (wl18xx):
         - support newer firmware versions
      - RealTek (rtw89):
         - preparation for RTL8852BE-VT support
         - Wake on WLAN support for WiFi 6 chips
         - 36-bit PCI DMA support
      - RealTek (rtlwifi):
         - RTL8192DU support
      - Broadcom (brcmfmac):
         - Management Frame Protection support (to enable WPA3)

   - Bluetooth:
      - qualcomm: use the power sequencer for QCA6390
      - btusb: mediatek: add ISO data transmission functions
      - hci_bcm4377: add BCM4388 support
      - btintel: add support for BlazarU core
      - btintel: add support for Whale Peak2
      - btnxpuart: add support for AW693 A1 chipset
      - btnxpuart: add support for IW615 chipset
      - btusb: add Realtek RTL8852BE support ID 0x13d3:0x3591"

* tag 'net-next-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1589 commits)
  eth: fbnic: Fix spelling mistake "tiggerring" -> "triggering"
  tcp: Replace strncpy() with strscpy()
  wifi: ath12k: fix build vs old compiler
  tcp: Don't access uninit tcp_rsk(req)->ao_keyid in tcp_create_openreq_child().
  eth: fbnic: Write the TCAM tables used for RSS control and Rx to host
  eth: fbnic: Add L2 address programming
  eth: fbnic: Add basic Rx handling
  eth: fbnic: Add basic Tx handling
  eth: fbnic: Add link detection
  eth: fbnic: Add initial messaging to notify FW of our presence
  eth: fbnic: Implement Rx queue alloc/start/stop/free
  eth: fbnic: Implement Tx queue alloc/start/stop/free
  eth: fbnic: Allocate a netdevice and napi vectors with queues
  eth: fbnic: Add FW communication mechanism
  eth: fbnic: Add message parsing for FW messages
  eth: fbnic: Add register init to set PCIe/Ethernet device config
  eth: fbnic: Allocate core device specific structures and devlink interface
  eth: fbnic: Add scaffolding for Meta's NIC driver
  PCI: Add Meta Platforms vendor ID
  net/sched: cls_flower: propagate tca[TCA_OPTIONS] to NL_REQ_ATTR_CHECK
  ...
Merge tag 'thermal-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm 2024-07-16T22:47:19+00:00 Linus Torvalds torvalds@linux-foundation.org 2024-07-16T22:47:19+00:00 15114e8fb58ffd574da83951e89cb5ab0055cc1e Pull thermal control updates from Rafael Wysocki: "These add some new hardware support (notably, the Lunar Lake platform support in int340x and X1E80100 temperature sensor), continue to rework the thermal driver interface to eliminate trip point IDs from it, update DT bindings for a number of platforms and simplify probe in a number of thermal drivers, address issues and clean up code. Specifics: - Add DLVR and MSI interrupt support for the Lunar Lake platform to the int340x thermal driver (Srinivas Pandruvada) - Enable workload type hints (WLT) support and power floor interrupt support for the Lunar Lake platform in int340x ((Srinivas Pandruvada) - Switch Intel thermal drivers to new Intel CPU model defines (Tony Luck) - Clean up the int3400 and int3403 drivers (Erick Archer and David Alan Gilbert) - Improve intel_pch_thermal kernel log messages printed during suspend to idle (Zhang Rui) - Make the intel_tcc_cooling driver use a model-specific bitmask for TCC offset (Ricardo Neri) - Redesign the .set_trip_temp() thermal zone callback to take a trip pointer instead of a trip ID and update its users (Rafael Wysocki) - Avoid using invalid combinations of polling_delay and passive_delay thermal zone parameters (Rafael Wysocki) - Update a cooling device registration function to take a const argument (Krzysztof Kozlowski) - Make the uniphier thermal driver use thermal_zone_for_each_trip() for walking trip points (Rafael Wysocki) - Fix and clean up several minor shortcomings in thermal debug (Rafael Wysocki) - Rename __thermal_zone_set_trips() to thermal_zone_set_trips() and make it use trip thresholds (Rafael Wysocki) - Use READ_ONCE() for lockless access to trip temperature and hysteresis (Rafael Wysocki) - Drop unnecessary cooling device target state checks from the Bang-Bang thermal governor (Rafael Wysocki) - Avoid invoking thermal governor .trip_crossed() callback for critical and hot trip points (Rafael Wysocki) - Group all Renesas drivers inside a dedicated sub directory and add the missing dependency to OF (Niklas Söderlund) - Add suspend/resume support on k3_j72xx_bandgap and take the opportunity to remove an unneeded delay in the init time code path (Théo Lebrun) - Fix thermal zone definition for MT8186 and MT8188 (Julien Panis) - Convert hisilicon-thermal.txt to dt-schema (Abdulrasaq Lawani) - Add DT bindings for the X1E80100 temperature sensor (Abel Vesa) - Fix the thermal zone node name regular expression in the DT schema (Krzysztof Kozlowski) - Avoid failing thermal control initialization by using default values on some platforms where calibration data is missing (Chen-Yu Tsai) - Fix the sensor cell size in DT for the Exynos platform (Krzysztof Kozlowski) - Bring the common definition of '#thermal-sensor-cells' property in order to simplify the bindings on all the platforms where this change makes sense and do some minor cleanups (Krzysztof Kozlowski) - Fix a race between removal and clock disable in the broadcom thermal driver (Krzysztof Kozlowski) - Drop 'trips' DT node as required from the thermal zone bindings in order to fix the remaining warnings appearing for thermal zones without trip points (Rob Herring) - Simplify all the drivers where dev_err_probe() can apply (Krzysztof Kozlowski) - Clean up code related to stih416 as this platform is not described anywhere (Raphael Gallais-Pou)" * tag 'thermal-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (81 commits) thermal/drivers/sti: Cleanup code related to stih416 thermal/drivers/generic-adc: Simplify with dev_err_probe() thermal/drivers/generic-adc: Simplify probe() with local dev variable thermal/drivers/qcom-tsens: Simplify with dev_err_probe() thermal/drivers/qcom-spmi-adc-tm5: Simplify with dev_err_probe() thermal/drivers/imx: Simplify with dev_err_probe() thermal/drivers/imx: Simplify probe() with local dev variable thermal/drivers/hisi: Simplify with dev_err_probe() thermal/drivers/exynos: Simplify with dev_err_probe() thermal/drivers/exynos: Simplify probe() with local dev variable thermal/drivers/broadcom: Simplify with dev_err_probe() thermal/drivers/broadcom: Simplify probe() with local dev variable thermal/drivers/broadcom: Fix race between removal and clock disable dt-bindings: thermal: Drop 'trips' node as required dt-bindings: thermal: qoriq: reference thermal-sensor schema dt-bindings: thermal: cleanup examples indentation dt-bindings: thermal: simplify few bindings dt-bindings: thermal: ti,j72xx: reference thermal-sensor schema dt-bindings: thermal: ti,am654: reference thermal-sensor schema dt-bindings: thermal: st,stm32: reference thermal-sensor schema ... 
Pull thermal control updates from Rafael Wysocki:
 "These add some new hardware support (notably, the Lunar Lake platform
  support in int340x and X1E80100 temperature sensor), continue to
  rework the thermal driver interface to eliminate trip point IDs from
  it, update DT bindings for a number of platforms and simplify probe in
  a number of thermal drivers, address issues and clean up code.

  Specifics:

   - Add DLVR and MSI interrupt support for the Lunar Lake platform to
     the int340x thermal driver (Srinivas Pandruvada)

   - Enable workload type hints (WLT) support and power floor interrupt
     support for the Lunar Lake platform in int340x ((Srinivas
     Pandruvada)

   - Switch Intel thermal drivers to new Intel CPU model defines (Tony
     Luck)

   - Clean up the int3400 and int3403 drivers (Erick Archer and David
     Alan Gilbert)

   - Improve intel_pch_thermal kernel log messages printed during
     suspend to idle (Zhang Rui)

   - Make the intel_tcc_cooling driver use a model-specific bitmask for
     TCC offset (Ricardo Neri)

   - Redesign the .set_trip_temp() thermal zone callback to take a trip
     pointer instead of a trip ID and update its users (Rafael Wysocki)

   - Avoid using invalid combinations of polling_delay and passive_delay
     thermal zone parameters (Rafael Wysocki)

   - Update a cooling device registration function to take a const
     argument (Krzysztof Kozlowski)

   - Make the uniphier thermal driver use thermal_zone_for_each_trip()
     for walking trip points (Rafael Wysocki)

   - Fix and clean up several minor shortcomings in thermal debug
     (Rafael Wysocki)

   - Rename __thermal_zone_set_trips() to thermal_zone_set_trips() and
     make it use trip thresholds (Rafael Wysocki)

   - Use READ_ONCE() for lockless access to trip temperature and
     hysteresis (Rafael Wysocki)

   - Drop unnecessary cooling device target state checks from the
     Bang-Bang thermal governor (Rafael Wysocki)

   - Avoid invoking thermal governor .trip_crossed() callback for
     critical and hot trip points (Rafael Wysocki)

   - Group all Renesas drivers inside a dedicated sub directory and add
     the missing dependency to OF (Niklas Söderlund)

   - Add suspend/resume support on k3_j72xx_bandgap and take the
     opportunity to remove an unneeded delay in the init time code path
     (Théo Lebrun)

   - Fix thermal zone definition for MT8186 and MT8188 (Julien Panis)

   - Convert hisilicon-thermal.txt to dt-schema (Abdulrasaq Lawani)

   - Add DT bindings for the X1E80100 temperature sensor (Abel Vesa)

   - Fix the thermal zone node name regular expression in the DT schema
     (Krzysztof Kozlowski)

   - Avoid failing thermal control initialization by using default
     values on some platforms where calibration data is missing (Chen-Yu
     Tsai)

   - Fix the sensor cell size in DT for the Exynos platform (Krzysztof
     Kozlowski)

   - Bring the common definition of '#thermal-sensor-cells' property in
     order to simplify the bindings on all the platforms where this
     change makes sense and do some minor cleanups (Krzysztof Kozlowski)

   - Fix a race between removal and clock disable in the broadcom
     thermal driver (Krzysztof Kozlowski)

   - Drop 'trips' DT node as required from the thermal zone bindings in
     order to fix the remaining warnings appearing for thermal zones
     without trip points (Rob Herring)

   - Simplify all the drivers where dev_err_probe() can apply (Krzysztof
     Kozlowski)

   - Clean up code related to stih416 as this platform is not described
     anywhere (Raphael Gallais-Pou)"

* tag 'thermal-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (81 commits)
  thermal/drivers/sti: Cleanup code related to stih416
  thermal/drivers/generic-adc: Simplify with dev_err_probe()
  thermal/drivers/generic-adc: Simplify probe() with local dev variable
  thermal/drivers/qcom-tsens: Simplify with dev_err_probe()
  thermal/drivers/qcom-spmi-adc-tm5: Simplify with dev_err_probe()
  thermal/drivers/imx: Simplify with dev_err_probe()
  thermal/drivers/imx: Simplify probe() with local dev variable
  thermal/drivers/hisi: Simplify with dev_err_probe()
  thermal/drivers/exynos: Simplify with dev_err_probe()
  thermal/drivers/exynos: Simplify probe() with local dev variable
  thermal/drivers/broadcom: Simplify with dev_err_probe()
  thermal/drivers/broadcom: Simplify probe() with local dev variable
  thermal/drivers/broadcom: Fix race between removal and clock disable
  dt-bindings: thermal: Drop 'trips' node as required
  dt-bindings: thermal: qoriq: reference thermal-sensor schema
  dt-bindings: thermal: cleanup examples indentation
  dt-bindings: thermal: simplify few bindings
  dt-bindings: thermal: ti,j72xx: reference thermal-sensor schema
  dt-bindings: thermal: ti,am654: reference thermal-sensor schema
  dt-bindings: thermal: st,stm32: reference thermal-sensor schema
  ...
thermal: trip: Pass trip pointer to .set_trip_temp() thermal zone callback 2024-07-12T13:14:01+00:00 Rafael J. Wysocki rafael.j.wysocki@intel.com 2024-07-02T14:42:33+00:00 0728c810873e1a94e8b767f9809af940c9307d60 Out of several drivers implementing the .set_trip_temp() thermal zone operation, three don't actually use the trip ID argument passed to it, two call __thermal_zone_get_trip() to get a struct thermal_trip corresponding to the given trip ID, and the other use the trip ID as an index into their own data structures with the assumption that it will always match the ordering of entries in the trips table passed to the core during thermal zone registration, which is fragile and not really guaranteed. Even though the trip IDs used by the core are in fact their indices in the trips table passed to it by the thermal zone creator, that is purely a matter of convenience and should not be relied on for correctness. For this reason, modify trip_point_temp_store() to pass a (const) trip pointer to .set_trip_temp() and adjust the drivers implementing it accordingly. This helps to simplify the drivers invoking __thermal_zone_get_trip() from their .set_trip_temp() callback functions because they will not need to do it now and the other drivers can store their internal trip indices in the priv field in struct thermal_trip and their .set_trip_temp() callback functions can get those indices from there. The intel_quark_dts thermal driver can instead use the trip type to determine the requisite trip index. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Link: https://patch.msgid.link/8392906.T7Z3S40VBb@rjwysocki.net [ rjw: Add missing colon and 2 empty code lines ] [ rjw: Add missing change in imx_thermal.c and adjust the changelog ] [ rjw: Drop an unused local variable ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> 
Out of several drivers implementing the .set_trip_temp() thermal zone
operation, three don't actually use the trip ID argument passed to it,
two call __thermal_zone_get_trip() to get a struct thermal_trip
corresponding to the given trip ID, and the other use the trip ID as an
index into their own data structures with the assumption that it will
always match the ordering of entries in the trips table passed to the
core during thermal zone registration, which is fragile and not really
guaranteed.

Even though the trip IDs used by the core are in fact their indices in the
trips table passed to it by the thermal zone creator, that is purely a
matter of convenience and should not be relied on for correctness.

For this reason, modify trip_point_temp_store() to pass a (const) trip
pointer to .set_trip_temp() and adjust the drivers implementing it
accordingly.

This helps to simplify the drivers invoking __thermal_zone_get_trip()
from their .set_trip_temp() callback functions because they will not
need to do it now and the other drivers can store their internal
trip indices in the priv field in struct thermal_trip and their
.set_trip_temp() callback functions can get those indices from there.

The intel_quark_dts thermal driver can instead use the trip type to
determine the requisite trip index.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://patch.msgid.link/8392906.T7Z3S40VBb@rjwysocki.net
[ rjw: Add missing colon and 2 empty code lines ]
[ rjw: Add missing change in imx_thermal.c and adjust the changelog ]
[ rjw: Drop an unused local variable ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Merge tag 'wireless-next-2024-07-11' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next 2024-07-12T00:22:04+00:00 Jakub Kicinski kuba@kernel.org 2024-07-12T00:22:04+00:00 80ab5445da623540ea6303740015dd0210a06dc8 Kalle Valo says: ==================== wireless-next patches for v6.11 Most likely the last "new features" pull request for v6.11 with changes both in stack and in drivers. The big thing is the multiple radios for wiphy feature which makes it possible to better advertise radio capabilities to user space. mt76 enabled MLO and iwlwifi re-enabled MLO, ath12k and rtw89 Wi-Fi 6 devices got WoWLAN support. Major changes: cfg80211/mac80211 * remove DEAUTH_NEED_MGD_TX_PREP flag * multiple radios per wiphy support mac80211_hwsim * multi-radio wiphy support ath12k * DebugFS support for datapath statistics * WCN7850: support for WoW (Wake on WLAN) * WCN7850: device-tree bindings ath11k * QCA6390: device-tree bindings iwlwifi * mvm: re-enable Multi-Link Operation (MLO) * aggregation (A-MSDU) optimisations rtw89 * preparation for RTL8852BE-VT support * WoWLAN support for WiFi 6 chips * 36-bit PCI DMA support mt76 * mt7925 Multi-Link Operation (MLO) support * tag 'wireless-next-2024-07-11' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (204 commits) wifi: mac80211: fix AP chandef capturing in CSA wifi: iwlwifi: correctly reference TSO page information wifi: mt76: mt792x: fix scheduler interference in drv own process wifi: mt76: mt7925: enabling MLO when the firmware supports it wifi: mt76: mt7925: remove the unused mt7925_mcu_set_chan_info wifi: mt76: mt7925: update mt7925_mac_link_bss_add for MLO wifi: mt76: mt7925: update mt7925_mcu_bss_basic_tlv for MLO wifi: mt76: mt7925: update mt7925_mcu_set_timing for MLO wifi: mt76: mt7925: update mt7925_mcu_sta_phy_tlv for MLO wifi: mt76: mt7925: update mt7925_mcu_sta_rate_ctrl_tlv for MLO wifi: mt76: mt7925: add mt7925_mcu_sta_eht_mld_tlv for MLO wifi: mt76: mt7925: update mt7925_mcu_sta_update for MLO wifi: mt76: mt7925: update mt7925_mcu_add_bss_info for MLO wifi: mt76: mt7925: update mt7925_mcu_bss_mld_tlv for MLO wifi: mt76: mt7925: update mt7925_mcu_sta_mld_tlv for MLO wifi: mt76: mt7925: add mt7925_[assign,unassign]_vif_chanctx wifi: mt76: add def_wcid to struct mt76_wcid wifi: mt76: mt7925: report link information in rx status wifi: mt76: mt7925: update rate index according to link id wifi: mt76: mt7925: add link handling in the mt7925_ipv6_addr_change ... ==================== Link: https://patch.msgid.link/20240711102353.0C849C116B1@smtp.kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> 
Kalle Valo says:

====================
wireless-next patches for v6.11

Most likely the last "new features" pull request for v6.11 with
changes both in stack and in drivers. The big thing is the multiple
radios for wiphy feature which makes it possible to better advertise
radio capabilities to user space. mt76 enabled MLO and iwlwifi
re-enabled MLO, ath12k and rtw89 Wi-Fi 6 devices got WoWLAN support.

Major changes:

cfg80211/mac80211
 * remove DEAUTH_NEED_MGD_TX_PREP flag
 * multiple radios per wiphy support

mac80211_hwsim
 * multi-radio wiphy support

ath12k
 * DebugFS support for datapath statistics
 * WCN7850: support for WoW (Wake on WLAN)
 * WCN7850: device-tree bindings

ath11k
 * QCA6390: device-tree bindings

iwlwifi
 * mvm: re-enable Multi-Link Operation (MLO)
 * aggregation (A-MSDU) optimisations

rtw89
 * preparation for RTL8852BE-VT support
 * WoWLAN support for WiFi 6 chips
 * 36-bit PCI DMA support

mt76
 * mt7925 Multi-Link Operation (MLO) support

* tag 'wireless-next-2024-07-11' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (204 commits)
  wifi: mac80211: fix AP chandef capturing in CSA
  wifi: iwlwifi: correctly reference TSO page information
  wifi: mt76: mt792x: fix scheduler interference in drv own process
  wifi: mt76: mt7925: enabling MLO when the firmware supports it
  wifi: mt76: mt7925: remove the unused mt7925_mcu_set_chan_info
  wifi: mt76: mt7925: update mt7925_mac_link_bss_add for MLO
  wifi: mt76: mt7925: update mt7925_mcu_bss_basic_tlv for MLO
  wifi: mt76: mt7925: update mt7925_mcu_set_timing for MLO
  wifi: mt76: mt7925: update mt7925_mcu_sta_phy_tlv for MLO
  wifi: mt76: mt7925: update mt7925_mcu_sta_rate_ctrl_tlv for MLO
  wifi: mt76: mt7925: add mt7925_mcu_sta_eht_mld_tlv for MLO
  wifi: mt76: mt7925: update mt7925_mcu_sta_update for MLO
  wifi: mt76: mt7925: update mt7925_mcu_add_bss_info for MLO
  wifi: mt76: mt7925: update mt7925_mcu_bss_mld_tlv for MLO
  wifi: mt76: mt7925: update mt7925_mcu_sta_mld_tlv for MLO
  wifi: mt76: mt7925: add mt7925_[assign,unassign]_vif_chanctx
  wifi: mt76: add def_wcid to struct mt76_wcid
  wifi: mt76: mt7925: report link information in rx status
  wifi: mt76: mt7925: update rate index according to link id
  wifi: mt76: mt7925: add link handling in the mt7925_ipv6_addr_change
  ...
====================

Link: https://patch.msgid.link/20240711102353.0C849C116B1@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
wifi: iwlwifi: correctly reference TSO page information 2024-07-10T10:35:32+00:00 Benjamin Berg benjamin.berg@intel.com 2024-07-09T12:31:49+00:00 003eae5a28c6c9d50290a4ac9b955be912f24c9f The code got copied from get_workaround_page, but here p->page is the correct way to reference the page. Signed-off-by: Benjamin Berg <benjamin.berg@intel.com> Fixes: adc902ceada2 ("wifi: iwlwifi: keep the TSO and workaround pages mapped") Reported-by: kernel test robot <lkp@intel.com> Reported-by: Dan Carpenter <dan.carpenter@linaro.org> Closes: https://lore.kernel.org/r/202407062135.NNjnmMdR-lkp@intel.com/ Link: https://patch.msgid.link/20240709123149.1848315-1-benjamin@sipsolutions.net Signed-off-by: Johannes Berg <johannes.berg@intel.com> 
The code got copied from get_workaround_page, but here p->page is the
correct way to reference the page.

Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Fixes: adc902ceada2 ("wifi: iwlwifi: keep the TSO and workaround pages mapped")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/r/202407062135.NNjnmMdR-lkp@intel.com/
Link: https://patch.msgid.link/20240709123149.1848315-1-benjamin@sipsolutions.net
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
wifi: ipw2x00: Use kzalloc() instead of kmalloc()/memset() 2024-07-09T10:16:05+00:00 Chen Ni nichen@iscas.ac.cn 2024-07-04T09:06:22+00:00 3588e6438a1c2e353616959ce16bce06aef0e424 Replace kmalloc() + memset() to kzalloc() for better code readability and simplicity. Signed-off-by: Chen Ni <nichen@iscas.ac.cn> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://patch.msgid.link/20240704090622.2260102-1-nichen@iscas.ac.cn 
Replace kmalloc() + memset() to kzalloc() for
better code readability and simplicity.

Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20240704090622.2260102-1-nichen@iscas.ac.cn
Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net 2024-07-04T21:16:11+00:00 Jakub Kicinski kuba@kernel.org 2024-07-04T21:11:03+00:00 76ed626479ebe0227728eff16bb44544ebd98920 Cross-merge networking fixes after downstream PR. Conflicts: drivers/net/phy/aquantia/aquantia.h 219343755eae ("net: phy: aquantia: add missing include guards") 61578f679378 ("net: phy: aquantia: add support for PHY LEDs") drivers/net/ethernet/wangxun/libwx/wx_hw.c bd07a9817846 ("net: txgbe: remove separate irq request for MSI and INTx") b501d261a5b3 ("net: txgbe: add FDIR ATR support") https://lore.kernel.org/all/20240703112936.483c1975@canb.auug.org.au/ include/linux/mlx5/mlx5_ifc.h 048a403648fc ("net/mlx5: IFC updates for changing max EQs") 99be56171fa9 ("net/mlx5e: SHAMPO, Re-enable HW-GRO") https://lore.kernel.org/all/20240701133951.6926b2e3@canb.auug.org.au/ Adjacent changes: drivers/net/wireless/intel/iwlwifi/mvm/mac80211.c 4130c67cd123 ("wifi: iwlwifi: mvm: check vif for NULL/ERR_PTR before dereference") 3f3126515fbe ("wifi: iwlwifi: mvm: add mvm-specific guard") include/net/mac80211.h 816c6bec09ed ("wifi: mac80211: fix BSS_CHANGED_UNSOL_BCAST_PROBE_RESP") 5a009b42e041 ("wifi: mac80211: track changes in AP's TPE") Signed-off-by: Jakub Kicinski <kuba@kernel.org> 
Cross-merge networking fixes after downstream PR.

Conflicts:

drivers/net/phy/aquantia/aquantia.h
  219343755eae ("net: phy: aquantia: add missing include guards")
  61578f679378 ("net: phy: aquantia: add support for PHY LEDs")

drivers/net/ethernet/wangxun/libwx/wx_hw.c
  bd07a9817846 ("net: txgbe: remove separate irq request for MSI and INTx")
  b501d261a5b3 ("net: txgbe: add FDIR ATR support")
https://lore.kernel.org/all/20240703112936.483c1975@canb.auug.org.au/

include/linux/mlx5/mlx5_ifc.h
  048a403648fc ("net/mlx5: IFC updates for changing max EQs")
  99be56171fa9 ("net/mlx5e: SHAMPO, Re-enable HW-GRO")
https://lore.kernel.org/all/20240701133951.6926b2e3@canb.auug.org.au/

Adjacent changes:

drivers/net/wireless/intel/iwlwifi/mvm/mac80211.c
  4130c67cd123 ("wifi: iwlwifi: mvm: check vif for NULL/ERR_PTR before dereference")
  3f3126515fbe ("wifi: iwlwifi: mvm: add mvm-specific guard")

include/net/mac80211.h
  816c6bec09ed ("wifi: mac80211: fix BSS_CHANGED_UNSOL_BCAST_PROBE_RESP")
  5a009b42e041 ("wifi: mac80211: track changes in AP's TPE")

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
wifi: iwlwifi: mvm: re-enable MLO 2024-07-04T11:50:10+00:00 Miri Korenblit miriam.rachel.korenblit@intel.com 2024-07-03T10:27:37+00:00 1b431ba4ef9a760e7643d6fbc53bf522d59650f3 MLO was temporarily disabled by commit 5f404005055 ("wifi: iwlwifi: mvm: disable MLO for the time being"), until it will stabilize. Now, that all the bugs were fixed and the minimum FW version was bumped to a stable one, we can re-enable MLO back. Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com> Link: https://patch.msgid.link/20240703132713.8f77a71c3902.Ib302054cbd8fba82db97eb5298b2aaf8bbe106df@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com> 
MLO was temporarily disabled by
commit 5f404005055 ("wifi: iwlwifi: mvm: disable MLO for the time being"),
until it will stabilize.
Now, that all the bugs were fixed and the minimum FW version was bumped
to a stable one, we can re-enable MLO back.

Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240703132713.8f77a71c3902.Ib302054cbd8fba82db97eb5298b2aaf8bbe106df@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
wifi: iwlwifi: Add support for LARI_CONFIG_CHANGE_CMD v12 2024-07-04T11:50:06+00:00 Anjaneyulu pagadala.yesu.anjaneyulu@intel.com 2024-07-03T09:59:06+00:00 ef7ddf4e2f949633bd7b2b01c2e0f023aefb6987 Add support for activate/deactivate unii4 in USA, Canada and WW by reading DSM function 8 from UEFI or ACPI and sending it to the FW. Signed-off-by: Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com> Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com> Link: https://patch.msgid.link/20240703125541.674604cbb6d1.Ibb946ae8ce7a760940a3c9d101e7f4f1808c43e4@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com> 
Add support for activate/deactivate unii4 in USA, Canada and WW by
reading DSM function 8 from UEFI or ACPI and sending it to the FW.

Signed-off-by: Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240703125541.674604cbb6d1.Ibb946ae8ce7a760940a3c9d101e7f4f1808c43e4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>