When immediate quiet bit is set in CSA, the entire channel is blocked
by the firmware. It is expected that all the MACs will evacuate the
channel and the phy will be eventually either moved or removed.

Currently, the phy context is just unreferenced and thus, the quiet
bit is kept set and it will be impossible to TX on this phy, if we
will need to reuse it in the future.  This can be seen when doing a
channel switch with mode=1 (quiet) twice from channel X to Y and then
back to channel X.

Fix that, by moving the phy context to a default channel when not
referenced anymore.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

When starting aggregation, the code checks the status of the queue
allocated to the aggregation tid, which might not yet be allocated
and thus the queue index may be invalid.
Fix this by reserving a new queue in case the queue id is invalid.

While at it, clean up some unreachable code (a condition that is
already handled earlier) and remove all the non-DQA comments since
non-DQA mode is no longer supported.

Fixes: cf961e16620f ("iwlwifi: mvm: support dqa-mode agg on non-shared queue")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

If the driver failed to resume from D3, it is possible that it has
no valid aux station. In such case, fw restart will end up in sending
station related commands with an invalid station id, which will
result in an assert.

Fix this by allocating a new station id for the aux station if it
does not have a valid id even in the case of fw restart.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

When a queue is reserved for aggregation, the queue id is assigned
to the tid_data. This is fine since iwl_mvm_sta_tx_agg_oper()
takes care of allocating the queue before actual tx starts.
When the reservation is cancelled (e.g. when the AP declined the
aggregation request) the tid_data is not cleared. As a result,
following tx for this tid was trying to use an unallocated queue.

Fix this by setting the txq_id for the tid to invalid when unreserving
the queue.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

After switching to a new channel, driver schedules session protection
time event in order to hear the beacon on the new channel.
The duration of the protection is two beacon intervals.
However, since we start to switch slightly before beacon with count 1, in
case we don't hear (or AP doesn't transmit) the very first beacon on the
new channel the protection ends without hearing any beacon at all.
At this stage the switch is not complete, the queues are closed and the
interface doesn't have quota yet or TBTT events. As the result, we are
stuck forever waiting for iwl_mvm_post_channel_switch() to be called.

Fix this by increasing the protection time to be 3 beacon intervals and
in addition drop the connection if the time event ends before we got any
beacon.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Some devices use a shared clock which is very sensitive to variations
and cause trouble in some situations.  We need to set a bit in the phy
configuration to indicate that to the FW.  To make this generic, add a
extra_phy_config_flags element to the device configuration and OR it
into the phy_cfg before sending it to the firmware.  And also create a
set of configurations for devices that use shared clocks and need this
extra bit to be set.

Fixes: c62446d2b028 ("iwlwifi: add new 9460 series PCI IDs")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

The earlier patch called the station add functions but didn't
assign their return value to the ret variable, so that the
checks for it were meaningless. Fix that.

Found by smatch:

.../mac80211.c:2560 iwl_mvm_start_ap_ibss() warn: we tested 'ret' before and it was 'false'
.../mac80211.c:2563 iwl_mvm_start_ap_ibss() warn: we tested 'ret' before and it was 'false'

Fixes: 3a89411cd31c ("iwlwifi: mvm: fix assert 0x2B00 on older FWs")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Currently when an IGTK is set for an AP, it is set as a regular key.
Since the cipher is set to CMAC, the STA_KEY_FLG_EXT flag is added to
the host command, which causes assert 0x253D on NICs that do not support
this.

Fixes: 85aeb58cec1a ("iwlwifi: mvm: Enable security on new TX API")
Signed-off-by: Beni Lev <beni.lev@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

The tid being used for the queue (cab_queue) for the MCAST
station has been changed recently to be 0 (for BE).
The flush path still flushed only the special tid (15)
which means that the firmware wasn't flushing the right
queue and we could get a firmware crash upon remove
station if we had an MCAST packet on the ring.

The current code that flushes queues for a station only
differentiates between internal stations (stations that
aren't instantiated in mac80211, like the MCAST station)
and the non-internal ones.
Internal stations can be either: BCAST (beacons), MCAST
(for cab_queue), GENERAL_PURPOSE (p2p dev, and sniffer
injection). The internal stations can use different tids.

To make the code simpler, just flush all the tids always
and add the special internal tid (15) for internal
stations. The firmware will know how to handle this even
if we hadn't any queue mapped that that tid.

Fixes: e340c1a6ef4b ("iwlwifi: mvm: Correctly set the tid for mcast queue")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

'default false' should be 'default n', though they happen to have the
same effect here, due to undefined symbols ('false' in this case)
evaluating to n in a tristate sense.

Remove the default instead of changing it. bool and tristate symbols
implicitly default to n.

Discovered with the
https://github.com/ulfalizer/Kconfiglib/blob/master/examples/list_undefined.py
script.

Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>