linux.git/drivers/net/wireless/ath, branch v6.5 Linux kernel source tree wifi: ath12k: Fix buffer overflow when scanning with extraie 2023-08-09T12:44:14+00:00 Wen Gong quic_wgong@quicinc.com 2023-08-09T08:12:41+00:00 06f2ab86a5b6ed55f013258de4be9319841853ea If cfg80211 is providing extraie's for a scanning process then ath12k will copy that over to the firmware. The extraie.len is a 32 bit value in struct element_info and describes the amount of bytes for the vendor information elements. The problem is the allocation of the buffer. It has to align the TLV sections by 4 bytes. But the code was using an u8 to store the newly calculated length of this section (with alignment). And the new calculated length was then used to allocate the skbuff. But the actual code to copy in the data is using the extraie.len and not the calculated "aligned" length. The length of extraie with IEEE80211_HW_SINGLE_SCAN_ON_ALL_BANDS enabled was 264 bytes during tests with a wifi card. But it only allocated 8 bytes (264 bytes % 256) for it. As consequence, the code to memcpy the extraie into the skb was then just overwriting data after skb->end. Things like shinfo were therefore corrupted. This could usually be seen by a crash in skb_zcopy_clear which tried to call a ubuf_info callback (using a bogus address). Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Signed-off-by: Wen Gong <quic_wgong@quicinc.com> Link: https://lore.kernel.org/r/20230809081241.32765-1-quic_wgong@quicinc.com Signed-off-by: Johannes Berg <johannes.berg@intel.com> 
If cfg80211 is providing extraie's for a scanning process then ath12k will
copy that over to the firmware. The extraie.len is a 32 bit value in struct
element_info and describes the amount of bytes for the vendor information
elements.

The problem is the allocation of the buffer. It has to align the TLV
sections by 4 bytes. But the code was using an u8 to store the newly
calculated length of this section (with alignment). And the new
calculated length was then used to allocate the skbuff. But the actual
code to copy in the data is using the extraie.len and not the calculated
"aligned" length.

The length of extraie with IEEE80211_HW_SINGLE_SCAN_ON_ALL_BANDS enabled
was 264 bytes during tests with a wifi card. But it only allocated 8
bytes (264 bytes % 256) for it. As consequence, the code to memcpy the
extraie into the skb was then just overwriting data after skb->end. Things
like shinfo were therefore corrupted. This could usually be seen by a crash
in skb_zcopy_clear which tried to call a ubuf_info callback (using a bogus
address).

Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4

Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Link: https://lore.kernel.org/r/20230809081241.32765-1-quic_wgong@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Revert "wifi: ath6k: silence false positive -Wno-dangling-pointer warning on GCC 12" 2023-07-26T07:09:28+00:00 Kalle Valo kvalo@kernel.org 2023-07-24T10:08:23+00:00 a1ce186db7f0e449f35d12fb55ae0da2a1b400e2 This reverts commit bd1d129daa3ede265a880e2c6a7f91eab0f4dc62. The dangling-pointer warnings were disabled kernel-wide by commit 49beadbd47c2 ("gcc-12: disable '-Wdangling-pointer' warning for now") for v5.19. So this hack in ath6kl is not needed anymore. Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20230724100823.2948804-1-kvalo@kernel.org 
This reverts commit bd1d129daa3ede265a880e2c6a7f91eab0f4dc62.

The dangling-pointer warnings were disabled kernel-wide by commit 49beadbd47c2
("gcc-12: disable '-Wdangling-pointer' warning for now") for v5.19. So this
hack in ath6kl is not needed anymore.

Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230724100823.2948804-1-kvalo@kernel.org
Revert "wifi: ath11k: Enable threaded NAPI" 2023-07-26T06:56:53+00:00 Kalle Valo quic_kvalo@quicinc.com 2023-07-20T15:14:44+00:00 d265ebe41c911314bd273c218a37088835959fa1 This reverts commit 13aa2fb692d3717767303817f35b3e650109add3. This commit broke QCN9074 initialisation: [ 358.960477] ath11k_pci 0000:04:00.0: ce desc not available for wmi command 36866 [ 358.960481] ath11k_pci 0000:04:00.0: failed to send WMI_STA_POWERSAVE_PARAM_CMDID [ 358.960484] ath11k_pci 0000:04:00.0: could not set uapsd params -105 As there's no fix available let's just revert it to get QCN9074 working again. Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217536 Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20230720151444.2016637-1-kvalo@kernel.org 
This reverts commit 13aa2fb692d3717767303817f35b3e650109add3.

This commit broke QCN9074 initialisation:

[  358.960477] ath11k_pci 0000:04:00.0: ce desc not available for wmi command 36866
[  358.960481] ath11k_pci 0000:04:00.0: failed to send WMI_STA_POWERSAVE_PARAM_CMDID
[  358.960484] ath11k_pci 0000:04:00.0: could not set uapsd params -105

As there's no fix available let's just revert it to get QCN9074 working again.

Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217536
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230720151444.2016637-1-kvalo@kernel.org
Merge tag 'net-next-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next 2023-06-28T23:43:10+00:00 Linus Torvalds torvalds@linux-foundation.org 2023-06-28T23:43:10+00:00 3a8a670eeeaa40d87bd38a587438952741980c18 Pull networking changes from Jakub Kicinski: "WiFi 7 and sendpage changes are the biggest pieces of work for this release. The latter will definitely require fixes but I think that we got it to a reasonable point. Core: - Rework the sendpage & splice implementations Instead of feeding data into sockets page by page extend sendmsg handlers to support taking a reference on the data, controlled by a new flag called MSG_SPLICE_PAGES Rework the handling of unexpected-end-of-file to invoke an additional callback instead of trying to predict what the right combination of MORE/NOTLAST flags is Remove the MSG_SENDPAGE_NOTLAST flag completely - Implement SCM_PIDFD, a new type of CMSG type analogous to SCM_CREDENTIALS, but it contains pidfd instead of plain pid - Enable socket busy polling with CONFIG_RT - Improve reliability and efficiency of reporting for ref_tracker - Auto-generate a user space C library for various Netlink families Protocols: - Allow TCP to shrink the advertised window when necessary, prevent sk_rcvbuf auto-tuning from growing the window all the way up to tcp_rmem[2] - Use per-VMA locking for "page-flipping" TCP receive zerocopy - Prepare TCP for device-to-device data transfers, by making sure that payloads are always attached to skbs as page frags - Make the backoff time for the first N TCP SYN retransmissions linear. Exponential backoff is unnecessarily conservative - Create a new MPTCP getsockopt to retrieve all info (MPTCP_FULL_INFO) - Avoid waking up applications using TLS sockets until we have a full record - Allow using kernel memory for protocol ioctl callbacks, paving the way to issuing ioctls over io_uring - Add nolocalbypass option to VxLAN, forcing packets to be fully encapsulated even if they are destined for a local IP address - Make TCPv4 use consistent hash in TIME_WAIT and SYN_RECV. Ensure in-kernel ECMP implementation (e.g. Open vSwitch) select the same link for all packets. Support L4 symmetric hashing in Open vSwitch - PPPoE: make number of hash bits configurable - Allow DNS to be overwritten by DHCPACK in the in-kernel DHCP client (ipconfig) - Add layer 2 miss indication and filtering, allowing higher layers (e.g. ACL filters) to make forwarding decisions based on whether packet matched forwarding state in lower devices (bridge) - Support matching on Connectivity Fault Management (CFM) packets - Hide the "link becomes ready" IPv6 messages by demoting their printk level to debug - HSR: don't enable promiscuous mode if device offloads the proto - Support active scanning in IEEE 802.15.4 - Continue work on Multi-Link Operation for WiFi 7 BPF: - Add precision propagation for subprogs and callbacks. This allows maintaining verification efficiency when subprograms are used, or in fact passing the verifier at all for complex programs, especially those using open-coded iterators - Improve BPF's {g,s}setsockopt() length handling. Previously BPF assumed the length is always equal to the amount of written data. But some protos allow passing a NULL buffer to discover what the output buffer *should* be, without writing anything - Accept dynptr memory as memory arguments passed to helpers - Add routing table ID to bpf_fib_lookup BPF helper - Support O_PATH FDs in BPF_OBJ_PIN and BPF_OBJ_GET commands - Drop bpf_capable() check in BPF_MAP_FREEZE command (used to mark maps as read-only) - Show target_{obj,btf}_id in tracing link fdinfo - Addition of several new kfuncs (most of the names are self-explanatory): - Add a set of new dynptr kfuncs: bpf_dynptr_adjust(), bpf_dynptr_is_null(), bpf_dynptr_is_rdonly(), bpf_dynptr_size() and bpf_dynptr_clone(). - bpf_task_under_cgroup() - bpf_sock_destroy() - force closing sockets - bpf_cpumask_first_and(), rework bpf_cpumask_any*() kfuncs Netfilter: - Relax set/map validation checks in nf_tables. Allow checking presence of an entry in a map without using the value - Increase ip_vs_conn_tab_bits range for 64BIT builds - Allow updating size of a set - Improve NAT tuple selection when connection is closing Driver API: - Integrate netdev with LED subsystem, to allow configuring HW "offloaded" blinking of LEDs based on link state and activity (i.e. packets coming in and out) - Support configuring rate selection pins of SFP modules - Factor Clause 73 auto-negotiation code out of the drivers, provide common helper routines - Add more fool-proof helpers for managing lifetime of MDIO devices associated with the PCS layer - Allow drivers to report advanced statistics related to Time Aware scheduler offload (taprio) - Allow opting out of VF statistics in link dump, to allow more VFs to fit into the message - Split devlink instance and devlink port operations New hardware / drivers: - Ethernet: - Synopsys EMAC4 IP support (stmmac) - Marvell 88E6361 8 port (5x1GE + 3x2.5GE) switches - Marvell 88E6250 7 port switches - Microchip LAN8650/1 Rev.B0 PHYs - MediaTek MT7981/MT7988 built-in 1GE PHY driver - WiFi: - Realtek RTL8192FU, 2.4 GHz, b/g/n mode, 2T2R, 300 Mbps - Realtek RTL8723DS (SDIO variant) - Realtek RTL8851BE - CAN: - Fintek F81604 Drivers: - Ethernet NICs: - Intel (100G, ice): - support dynamic interrupt allocation - use meta data match instead of VF MAC addr on slow-path - nVidia/Mellanox: - extend link aggregation to handle 4, rather than just 2 ports - spawn sub-functions without any features by default - OcteonTX2: - support HTB (Tx scheduling/QoS) offload - make RSS hash generation configurable - support selecting Rx queue using TC filters - Wangxun (ngbe/txgbe): - add basic Tx/Rx packet offloads - add phylink support (SFP/PCS control) - Freescale/NXP (enetc): - report TAPRIO packet statistics - Solarflare/AMD: - support matching on IP ToS and UDP source port of outer header - VxLAN and GENEVE tunnel encapsulation over IPv4 or IPv6 - add devlink dev info support for EF10 - Virtual NICs: - Microsoft vNIC: - size the Rx indirection table based on requested configuration - support VLAN tagging - Amazon vNIC: - try to reuse Rx buffers if not fully consumed, useful for ARM servers running with 16kB pages - Google vNIC: - support TCP segmentation of >64kB frames - Ethernet embedded switches: - Marvell (mv88e6xxx): - enable USXGMII (88E6191X) - Microchip: - lan966x: add support for Egress Stage 0 ACL engine - lan966x: support mapping packet priority to internal switch priority (based on PCP or DSCP) - Ethernet PHYs: - Broadcom PHYs: - support for Wake-on-LAN for BCM54210E/B50212E - report LPI counter - Microsemi PHYs: support RGMII delay configuration (VSC85xx) - Micrel PHYs: receive timestamp in the frame (LAN8841) - Realtek PHYs: support optional external PHY clock - Altera TSE PCS: merge the driver into Lynx PCS which it is a variant of - CAN: Kvaser PCIEcan: - support packet timestamping - WiFi: - Intel (iwlwifi): - major update for new firmware and Multi-Link Operation (MLO) - configuration rework to drop test devices and split the different families - support for segmented PNVM images and power tables - new vendor entries for PPAG (platform antenna gain) feature - Qualcomm 802.11ax (ath11k): - Multiple Basic Service Set Identifier (MBSSID) and Enhanced MBSSID Advertisement (EMA) support in AP mode - support factory test mode - RealTek (rtw89): - add RSSI based antenna diversity - support U-NII-4 channels on 5 GHz band - RealTek (rtl8xxxu): - AP mode support for 8188f - support USB RX aggregation for the newer chips" * tag 'net-next-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1602 commits) net: scm: introduce and use scm_recv_unix helper af_unix: Skip SCM_PIDFD if scm->pid is NULL. net: lan743x: Simplify comparison netlink: Add __sock_i_ino() for __netlink_diag_dump(). net: dsa: avoid suspicious RCU usage for synced VLAN-aware MAC addresses Revert "af_unix: Call scm_recv() only after scm_set_cred()." phylink: ReST-ify the phylink_pcs_neg_mode() kdoc libceph: Partially revert changes to support MSG_SPLICE_PAGES net: phy: mscc: fix packet loss due to RGMII delays net: mana: use vmalloc_array and vcalloc net: enetc: use vmalloc_array and vcalloc ionic: use vmalloc_array and vcalloc pds_core: use vmalloc_array and vcalloc gve: use vmalloc_array and vcalloc octeon_ep: use vmalloc_array and vcalloc net: usb: qmi_wwan: add u-blox 0x1312 composition perf trace: fix MSG_SPLICE_PAGES build error ipvlan: Fix return value of ipvlan_queue_xmit() netfilter: nf_tables: fix underflow in chain reference counter netfilter: nf_tables: unbind non-anonymous set if rule construction fails ... 
Pull networking changes from Jakub Kicinski:
 "WiFi 7 and sendpage changes are the biggest pieces of work for this
  release. The latter will definitely require fixes but I think that we
  got it to a reasonable point.

  Core:

   - Rework the sendpage & splice implementations

     Instead of feeding data into sockets page by page extend sendmsg
     handlers to support taking a reference on the data, controlled by a
     new flag called MSG_SPLICE_PAGES

     Rework the handling of unexpected-end-of-file to invoke an
     additional callback instead of trying to predict what the right
     combination of MORE/NOTLAST flags is

     Remove the MSG_SENDPAGE_NOTLAST flag completely

   - Implement SCM_PIDFD, a new type of CMSG type analogous to
     SCM_CREDENTIALS, but it contains pidfd instead of plain pid

   - Enable socket busy polling with CONFIG_RT

   - Improve reliability and efficiency of reporting for ref_tracker

   - Auto-generate a user space C library for various Netlink families

  Protocols:

   - Allow TCP to shrink the advertised window when necessary, prevent
     sk_rcvbuf auto-tuning from growing the window all the way up to
     tcp_rmem[2]

   - Use per-VMA locking for "page-flipping" TCP receive zerocopy

   - Prepare TCP for device-to-device data transfers, by making sure
     that payloads are always attached to skbs as page frags

   - Make the backoff time for the first N TCP SYN retransmissions
     linear. Exponential backoff is unnecessarily conservative

   - Create a new MPTCP getsockopt to retrieve all info
     (MPTCP_FULL_INFO)

   - Avoid waking up applications using TLS sockets until we have a full
     record

   - Allow using kernel memory for protocol ioctl callbacks, paving the
     way to issuing ioctls over io_uring

   - Add nolocalbypass option to VxLAN, forcing packets to be fully
     encapsulated even if they are destined for a local IP address

   - Make TCPv4 use consistent hash in TIME_WAIT and SYN_RECV. Ensure
     in-kernel ECMP implementation (e.g. Open vSwitch) select the same
     link for all packets. Support L4 symmetric hashing in Open vSwitch

   - PPPoE: make number of hash bits configurable

   - Allow DNS to be overwritten by DHCPACK in the in-kernel DHCP client
     (ipconfig)

   - Add layer 2 miss indication and filtering, allowing higher layers
     (e.g. ACL filters) to make forwarding decisions based on whether
     packet matched forwarding state in lower devices (bridge)

   - Support matching on Connectivity Fault Management (CFM) packets

   - Hide the "link becomes ready" IPv6 messages by demoting their
     printk level to debug

   - HSR: don't enable promiscuous mode if device offloads the proto

   - Support active scanning in IEEE 802.15.4

   - Continue work on Multi-Link Operation for WiFi 7

  BPF:

   - Add precision propagation for subprogs and callbacks. This allows
     maintaining verification efficiency when subprograms are used, or
     in fact passing the verifier at all for complex programs,
     especially those using open-coded iterators

   - Improve BPF's {g,s}setsockopt() length handling. Previously BPF
     assumed the length is always equal to the amount of written data.
     But some protos allow passing a NULL buffer to discover what the
     output buffer *should* be, without writing anything

   - Accept dynptr memory as memory arguments passed to helpers

   - Add routing table ID to bpf_fib_lookup BPF helper

   - Support O_PATH FDs in BPF_OBJ_PIN and BPF_OBJ_GET commands

   - Drop bpf_capable() check in BPF_MAP_FREEZE command (used to mark
     maps as read-only)

   - Show target_{obj,btf}_id in tracing link fdinfo

   - Addition of several new kfuncs (most of the names are
     self-explanatory):
      - Add a set of new dynptr kfuncs: bpf_dynptr_adjust(),
        bpf_dynptr_is_null(), bpf_dynptr_is_rdonly(), bpf_dynptr_size()
        and bpf_dynptr_clone().
      - bpf_task_under_cgroup()
      - bpf_sock_destroy() - force closing sockets
      - bpf_cpumask_first_and(), rework bpf_cpumask_any*() kfuncs

  Netfilter:

   - Relax set/map validation checks in nf_tables. Allow checking
     presence of an entry in a map without using the value

   - Increase ip_vs_conn_tab_bits range for 64BIT builds

   - Allow updating size of a set

   - Improve NAT tuple selection when connection is closing

  Driver API:

   - Integrate netdev with LED subsystem, to allow configuring HW
     "offloaded" blinking of LEDs based on link state and activity
     (i.e. packets coming in and out)

   - Support configuring rate selection pins of SFP modules

   - Factor Clause 73 auto-negotiation code out of the drivers, provide
     common helper routines

   - Add more fool-proof helpers for managing lifetime of MDIO devices
     associated with the PCS layer

   - Allow drivers to report advanced statistics related to Time Aware
     scheduler offload (taprio)

   - Allow opting out of VF statistics in link dump, to allow more VFs
     to fit into the message

   - Split devlink instance and devlink port operations

  New hardware / drivers:

   - Ethernet:
      - Synopsys EMAC4 IP support (stmmac)
      - Marvell 88E6361 8 port (5x1GE + 3x2.5GE) switches
      - Marvell 88E6250 7 port switches
      - Microchip LAN8650/1 Rev.B0 PHYs
      - MediaTek MT7981/MT7988 built-in 1GE PHY driver

   - WiFi:
      - Realtek RTL8192FU, 2.4 GHz, b/g/n mode, 2T2R, 300 Mbps
      - Realtek RTL8723DS (SDIO variant)
      - Realtek RTL8851BE

   - CAN:
      - Fintek F81604

  Drivers:

   - Ethernet NICs:
      - Intel (100G, ice):
         - support dynamic interrupt allocation
         - use meta data match instead of VF MAC addr on slow-path
      - nVidia/Mellanox:
         - extend link aggregation to handle 4, rather than just 2 ports
         - spawn sub-functions without any features by default
      - OcteonTX2:
         - support HTB (Tx scheduling/QoS) offload
         - make RSS hash generation configurable
         - support selecting Rx queue using TC filters
      - Wangxun (ngbe/txgbe):
         - add basic Tx/Rx packet offloads
         - add phylink support (SFP/PCS control)
      - Freescale/NXP (enetc):
         - report TAPRIO packet statistics
      - Solarflare/AMD:
         - support matching on IP ToS and UDP source port of outer
           header
         - VxLAN and GENEVE tunnel encapsulation over IPv4 or IPv6
         - add devlink dev info support for EF10

   - Virtual NICs:
      - Microsoft vNIC:
         - size the Rx indirection table based on requested
           configuration
         - support VLAN tagging
      - Amazon vNIC:
         - try to reuse Rx buffers if not fully consumed, useful for ARM
           servers running with 16kB pages
      - Google vNIC:
         - support TCP segmentation of >64kB frames

   - Ethernet embedded switches:
      - Marvell (mv88e6xxx):
         - enable USXGMII (88E6191X)
      - Microchip:
         - lan966x: add support for Egress Stage 0 ACL engine
         - lan966x: support mapping packet priority to internal switch
           priority (based on PCP or DSCP)

   - Ethernet PHYs:
      - Broadcom PHYs:
         - support for Wake-on-LAN for BCM54210E/B50212E
         - report LPI counter
      - Microsemi PHYs: support RGMII delay configuration (VSC85xx)
      - Micrel PHYs: receive timestamp in the frame (LAN8841)
      - Realtek PHYs: support optional external PHY clock
      - Altera TSE PCS: merge the driver into Lynx PCS which it is a
        variant of

   - CAN: Kvaser PCIEcan:
      - support packet timestamping

   - WiFi:
      - Intel (iwlwifi):
         - major update for new firmware and Multi-Link Operation (MLO)
         - configuration rework to drop test devices and split the
           different families
         - support for segmented PNVM images and power tables
         - new vendor entries for PPAG (platform antenna gain) feature
      - Qualcomm 802.11ax (ath11k):
         - Multiple Basic Service Set Identifier (MBSSID) and Enhanced
           MBSSID Advertisement (EMA) support in AP mode
         - support factory test mode
      - RealTek (rtw89):
         - add RSSI based antenna diversity
         - support U-NII-4 channels on 5 GHz band
      - RealTek (rtl8xxxu):
         - AP mode support for 8188f
         - support USB RX aggregation for the newer chips"

* tag 'net-next-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1602 commits)
  net: scm: introduce and use scm_recv_unix helper
  af_unix: Skip SCM_PIDFD if scm->pid is NULL.
  net: lan743x: Simplify comparison
  netlink: Add __sock_i_ino() for __netlink_diag_dump().
  net: dsa: avoid suspicious RCU usage for synced VLAN-aware MAC addresses
  Revert "af_unix: Call scm_recv() only after scm_set_cred()."
  phylink: ReST-ify the phylink_pcs_neg_mode() kdoc
  libceph: Partially revert changes to support MSG_SPLICE_PAGES
  net: phy: mscc: fix packet loss due to RGMII delays
  net: mana: use vmalloc_array and vcalloc
  net: enetc: use vmalloc_array and vcalloc
  ionic: use vmalloc_array and vcalloc
  pds_core: use vmalloc_array and vcalloc
  gve: use vmalloc_array and vcalloc
  octeon_ep: use vmalloc_array and vcalloc
  net: usb: qmi_wwan: add u-blox 0x1312 composition
  perf trace: fix MSG_SPLICE_PAGES build error
  ipvlan: Fix return value of ipvlan_queue_xmit()
  netfilter: nf_tables: fix underflow in chain reference counter
  netfilter: nf_tables: unbind non-anonymous set if rule construction fails
  ...
wifi: ath10k: improve structure padding 2023-06-21T18:08:05+00:00 Arnd Bergmann arnd@arndb.de 2023-06-16T09:04:21+00:00 12ec37be3faf9df7831ce210947f111b3417baf3 Including an aligned structure inside of a packed one is ambiguous and can lead to misaligned data, as pointed out by this clang warning: drivers/net/wireless/ath/ath10k/htt.h:715:34: error: field prefix within 'struct htt_rx_indication' is less aligned than 'struct htt_rx_indication_prefix' and is usually due to 'struct htt_rx_indication' being packed, which can lead to unaligned accesses [-Werror,-Wunaligned-access] struct htt_rx_indication_prefix prefix; ^ drivers/net/wireless/ath/ath10k/htt.h:736:34: error: field prefix within 'struct htt_rx_indication_hl' is less aligned than 'struct htt_rx_indication_prefix' and is usually due to 'struct htt_rx_indication_hl' being packed, which can lead to unaligned accesses [-Werror,-Wunaligned-access] struct htt_rx_indication_prefix prefix; ^ drivers/net/wireless/ath/ath10k/htt.h:1564:2: error: field within 'struct htt_tx_fetch_ind' is less aligned than 'union htt_tx_fetch_ind::(anonymous at drivers/net/wireless/ath/ath10k/htt.h:1564:2)' and is usually due to 'struct htt_tx_fetch_ind' being packed, which can lead to unaligned accesses [-Werror,-Wunaligned-access] union { ^ drivers/net/wireless/ath/ath10k/htt.h:1702:2: error: field within 'struct htt_resp' is less aligned than 'union htt_resp::(anonymous at drivers/net/wireless/ath/ath10k/htt.h:1702:2)' and is usually due to 'struct htt_resp' being packed, which can lead to unaligned accesses [-Werror,-Wunaligned-access] These structures appear to actually need the packing since they are embedded at misaligned offsets. Add even more such annotations here to enforce bytewise access throughout the driver. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20230616090439.2484857-1-arnd@kernel.org 
Including an aligned structure inside of a packed one is ambiguous
and can lead to misaligned data, as pointed out by this clang warning:

drivers/net/wireless/ath/ath10k/htt.h:715:34: error: field prefix within 'struct htt_rx_indication' is less aligned than 'struct htt_rx_indication_prefix' and is usually due to 'struct htt_rx_indication' being packed, which can lead to unaligned accesses [-Werror,-Wunaligned-access]
        struct htt_rx_indication_prefix prefix;
                                        ^
drivers/net/wireless/ath/ath10k/htt.h:736:34: error: field prefix within 'struct htt_rx_indication_hl' is less aligned than 'struct htt_rx_indication_prefix' and is usually due to 'struct htt_rx_indication_hl' being packed, which can lead to unaligned accesses [-Werror,-Wunaligned-access]
        struct htt_rx_indication_prefix prefix;
                                        ^
drivers/net/wireless/ath/ath10k/htt.h:1564:2: error: field  within 'struct htt_tx_fetch_ind' is less aligned than 'union htt_tx_fetch_ind::(anonymous at drivers/net/wireless/ath/ath10k/htt.h:1564:2)' and is usually due to 'struct htt_tx_fetch_ind' being packed, which can lead to unaligned accesses [-Werror,-Wunaligned-access]
        union {
        ^
drivers/net/wireless/ath/ath10k/htt.h:1702:2: error: field  within 'struct htt_resp' is less aligned than 'union htt_resp::(anonymous at drivers/net/wireless/ath/ath10k/htt.h:1702:2)' and is usually due to 'struct htt_resp' being packed, which can lead to unaligned accesses [-Werror,-Wunaligned-access]

These structures appear to actually need the packing since they
are embedded at misaligned offsets. Add even more such annotations
here to enforce bytewise access throughout the driver.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230616090439.2484857-1-arnd@kernel.org
wifi: ath9k: convert msecs to jiffies where needed 2023-06-21T18:07:22+00:00 Dmitry Antipov dmantipov@yandex.ru 2023-06-13T13:46:55+00:00 2aa083acea9f61be3280184384551178f510ff51 Since 'ieee80211_queue_delayed_work()' expects timeout in jiffies and not milliseconds, 'msecs_to_jiffies()' should be used in 'ath_restart_work()' and '__ath9k_flush()'. Fixes: d63ffc45c5d3 ("ath9k: rename tx_complete_work to hw_check_work") Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru> Acked-by: Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20230613134655.248728-1-dmantipov@yandex.ru 
Since 'ieee80211_queue_delayed_work()' expects timeout in
jiffies and not milliseconds, 'msecs_to_jiffies()' should
be used in 'ath_restart_work()' and '__ath9k_flush()'.

Fixes: d63ffc45c5d3 ("ath9k: rename tx_complete_work to hw_check_work")
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230613134655.248728-1-dmantipov@yandex.ru
wifi: ath11k: Add missing hw_ops->get_ring_selector() for IPQ5018 2023-06-16T16:07:41+00:00 Ziyang Huang hzyitc@outlook.com 2023-06-15T11:41:48+00:00 ce282d8de71f07f0056ea319541141152c65f552 During sending data after clients connected, hw_ops->get_ring_selector() will be called. But for IPQ5018, this member isn't set, and the following NULL pointer exception will be occurred: [ 38.840478] 8<--- cut here --- [ 38.840517] Unable to handle kernel NULL pointer dereference at virtual address 00000000 ... [ 38.923161] PC is at 0x0 [ 38.927930] LR is at ath11k_dp_tx+0x70/0x730 [ath11k] ... [ 39.063264] Process hostapd (pid: 1034, stack limit = 0x801ceb3d) [ 39.068994] Stack: (0x856a9a68 to 0x856aa000) ... [ 39.438467] [<7f323804>] (ath11k_dp_tx [ath11k]) from [<7f314e6c>] (ath11k_mac_op_tx+0x80/0x190 [ath11k]) [ 39.446607] [<7f314e6c>] (ath11k_mac_op_tx [ath11k]) from [<7f17dbe0>] (ieee80211_handle_wake_tx_queue+0x7c/0xc0 [mac80211]) [ 39.456162] [<7f17dbe0>] (ieee80211_handle_wake_tx_queue [mac80211]) from [<7f174450>] (ieee80211_probereq_get+0x584/0x704 [mac80211]) [ 39.467443] [<7f174450>] (ieee80211_probereq_get [mac80211]) from [<7f178c40>] (ieee80211_tx_prepare_skb+0x1f8/0x248 [mac80211]) [ 39.479334] [<7f178c40>] (ieee80211_tx_prepare_skb [mac80211]) from [<7f179e28>] (__ieee80211_subif_start_xmit+0x32c/0x3d4 [mac80211]) [ 39.491053] [<7f179e28>] (__ieee80211_subif_start_xmit [mac80211]) from [<7f17af08>] (ieee80211_tx_control_port+0x19c/0x288 [mac80211]) [ 39.502946] [<7f17af08>] (ieee80211_tx_control_port [mac80211]) from [<7f0fc704>] (nl80211_tx_control_port+0x174/0x1d4 [cfg80211]) [ 39.515017] [<7f0fc704>] (nl80211_tx_control_port [cfg80211]) from [<808ceac4>] (genl_rcv_msg+0x154/0x340) [ 39.526814] [<808ceac4>] (genl_rcv_msg) from [<808cdb74>] (netlink_rcv_skb+0xb8/0x11c) [ 39.536446] [<808cdb74>] (netlink_rcv_skb) from [<808ce1d0>] (genl_rcv+0x28/0x34) [ 39.544344] [<808ce1d0>] (genl_rcv) from [<808cd234>] (netlink_unicast+0x174/0x274) [ 39.551895] [<808cd234>] (netlink_unicast) from [<808cd510>] (netlink_sendmsg+0x1dc/0x440) [ 39.559362] [<808cd510>] (netlink_sendmsg) from [<808596e0>] (____sys_sendmsg+0x1a8/0x1fc) [ 39.567697] [<808596e0>] (____sys_sendmsg) from [<8085b1a8>] (___sys_sendmsg+0xa4/0xdc) [ 39.575941] [<8085b1a8>] (___sys_sendmsg) from [<8085b310>] (sys_sendmsg+0x44/0x74) [ 39.583841] [<8085b310>] (sys_sendmsg) from [<80300060>] (ret_fast_syscall+0x0/0x40) ... [ 39.620734] Code: bad PC value [ 39.625869] ---[ end trace 8aef983ad3cbc032 ]--- Fixes: ba60f2793d3a ("wifi: ath11k: initialize hw_ops for IPQ5018") Signed-off-by: Ziyang Huang <hzyitc@outlook.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/TYZPR01MB5556D6E3F63EAB5129D11420C953A@TYZPR01MB5556.apcprd01.prod.exchangelabs.com 
During sending data after clients connected, hw_ops->get_ring_selector()
will be called. But for IPQ5018, this member isn't set, and the
following NULL pointer exception will be occurred:

	[   38.840478] 8<--- cut here ---
	[   38.840517] Unable to handle kernel NULL pointer dereference at virtual address 00000000
	...
	[   38.923161] PC is at 0x0
	[   38.927930] LR is at ath11k_dp_tx+0x70/0x730 [ath11k]
	...
	[   39.063264] Process hostapd (pid: 1034, stack limit = 0x801ceb3d)
	[   39.068994] Stack: (0x856a9a68 to 0x856aa000)
	...
	[   39.438467] [<7f323804>] (ath11k_dp_tx [ath11k]) from [<7f314e6c>] (ath11k_mac_op_tx+0x80/0x190 [ath11k])
	[   39.446607] [<7f314e6c>] (ath11k_mac_op_tx [ath11k]) from [<7f17dbe0>] (ieee80211_handle_wake_tx_queue+0x7c/0xc0 [mac80211])
	[   39.456162] [<7f17dbe0>] (ieee80211_handle_wake_tx_queue [mac80211]) from [<7f174450>] (ieee80211_probereq_get+0x584/0x704 [mac80211])
	[   39.467443] [<7f174450>] (ieee80211_probereq_get [mac80211]) from [<7f178c40>] (ieee80211_tx_prepare_skb+0x1f8/0x248 [mac80211])
	[   39.479334] [<7f178c40>] (ieee80211_tx_prepare_skb [mac80211]) from [<7f179e28>] (__ieee80211_subif_start_xmit+0x32c/0x3d4 [mac80211])
	[   39.491053] [<7f179e28>] (__ieee80211_subif_start_xmit [mac80211]) from [<7f17af08>] (ieee80211_tx_control_port+0x19c/0x288 [mac80211])
	[   39.502946] [<7f17af08>] (ieee80211_tx_control_port [mac80211]) from [<7f0fc704>] (nl80211_tx_control_port+0x174/0x1d4 [cfg80211])
	[   39.515017] [<7f0fc704>] (nl80211_tx_control_port [cfg80211]) from [<808ceac4>] (genl_rcv_msg+0x154/0x340)
	[   39.526814] [<808ceac4>] (genl_rcv_msg) from [<808cdb74>] (netlink_rcv_skb+0xb8/0x11c)
	[   39.536446] [<808cdb74>] (netlink_rcv_skb) from [<808ce1d0>] (genl_rcv+0x28/0x34)
	[   39.544344] [<808ce1d0>] (genl_rcv) from [<808cd234>] (netlink_unicast+0x174/0x274)
	[   39.551895] [<808cd234>] (netlink_unicast) from [<808cd510>] (netlink_sendmsg+0x1dc/0x440)
	[   39.559362] [<808cd510>] (netlink_sendmsg) from [<808596e0>] (____sys_sendmsg+0x1a8/0x1fc)
	[   39.567697] [<808596e0>] (____sys_sendmsg) from [<8085b1a8>] (___sys_sendmsg+0xa4/0xdc)
	[   39.575941] [<8085b1a8>] (___sys_sendmsg) from [<8085b310>] (sys_sendmsg+0x44/0x74)
	[   39.583841] [<8085b310>] (sys_sendmsg) from [<80300060>] (ret_fast_syscall+0x0/0x40)
	...
	[   39.620734] Code: bad PC value
	[   39.625869] ---[ end trace 8aef983ad3cbc032 ]---

Fixes: ba60f2793d3a ("wifi: ath11k: initialize hw_ops for IPQ5018")
Signed-off-by: Ziyang Huang <hzyitc@outlook.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/TYZPR01MB5556D6E3F63EAB5129D11420C953A@TYZPR01MB5556.apcprd01.prod.exchangelabs.com
wifi: ath11k: Restart firmware after cold boot calibration for IPQ5018 2023-06-16T16:07:40+00:00 Ziyang Huang hzyitc@outlook.com 2023-06-15T11:41:48+00:00 80c5390e1f5e5b16d820512265530ef26073d8e0 Restart is required after cold boot calibration on IPQ5018. Otherwise, we get the following exception: [ 14.412829] qcom-q6-mpd cd00000.remoteproc: fatal error received: err_smem_ver.2.1: [ 14.412829] QC Image Version : QC_IMAGE_VERSION_STRING=WLAN.HK.2.6.0.1-00974-QCAHKSWPL_SILICONZ-1 [ 14.412829] Image Variant : IMAGE_VARIANT_STRING=5018.wlanfw2.map_spr_spr_evalQ [ 14.412829] DALSysLogEvent.c:174 Assertion 0 failed param0 :zero,param1 :zero,param2 :zero [ 14.412829] Thread ID : 0x00000048 Thread name : WLAN RT0 Process ID : 0x00000001 Process name :wlan0 [ 14.412829] [ 14.412829] Registers: [ 14.412829] SP : 0x4c81c120 [ 14.412829] FP : 0x4c81c138 [ 14.412829] PC : 0xb022c590 [ 14.412829] SSR : 0x00000000 [ 14.412829] BADVA : 0x00000000 [ 14.412829] LR : 0xb0008490 [ 14.412829] [ 14.412829] StackDump [ 14.412829] from:0x4c81c120 [ 14.412829] to: 0x00000000: [ 14.412829] [ 14.463006] remoteproc remoteproc0: crash detected in cd00000.remoteproc: type fatal error Fixes: 8dfe875aa24a ("wifi: ath11k: update hw params for IPQ5018") Signed-off-by: Ziyang Huang <hzyitc@outlook.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/TYZPR01MB55566969818BD4B49E770445C953A@TYZPR01MB5556.apcprd01.prod.exchangelabs.com 
Restart is required after cold boot calibration on IPQ5018. Otherwise,
we get the following exception:

	[   14.412829] qcom-q6-mpd cd00000.remoteproc: fatal error received: err_smem_ver.2.1:
	[   14.412829] QC Image Version : QC_IMAGE_VERSION_STRING=WLAN.HK.2.6.0.1-00974-QCAHKSWPL_SILICONZ-1
	[   14.412829] Image Variant : IMAGE_VARIANT_STRING=5018.wlanfw2.map_spr_spr_evalQ
	[   14.412829] DALSysLogEvent.c:174 Assertion 0 failed param0 :zero,param1 :zero,param2 :zero
	[   14.412829] Thread ID : 0x00000048 Thread name : WLAN RT0 Process ID : 0x00000001 Process name :wlan0
	[   14.412829]
	[   14.412829] Registers:
	[   14.412829] SP : 0x4c81c120
	[   14.412829] FP : 0x4c81c138
	[   14.412829] PC : 0xb022c590
	[   14.412829] SSR : 0x00000000
	[   14.412829] BADVA : 0x00000000
	[   14.412829] LR : 0xb0008490
	[   14.412829]
	[   14.412829] StackDump
	[   14.412829] from:0x4c81c120
	[   14.412829] to: 0x00000000:
	[   14.412829]
	[   14.463006] remoteproc remoteproc0: crash detected in cd00000.remoteproc: type fatal error

Fixes: 8dfe875aa24a ("wifi: ath11k: update hw params for IPQ5018")
Signed-off-by: Ziyang Huang <hzyitc@outlook.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/TYZPR01MB55566969818BD4B49E770445C953A@TYZPR01MB5556.apcprd01.prod.exchangelabs.com
wifi: ath11k: Add missing ops config for IPQ5018 in ath11k_ahb_probe() 2023-06-16T16:07:40+00:00 Ziyang Huang hzyitc@outlook.com 2023-06-15T11:41:47+00:00 469ddb20cae61cad9c4f208a4c8682305905a511 Without this patch, the IPQ5018 WiFi will fail and print the following logs: [ 11.033179] ath11k c000000.wifi: unsupported device type 7 [ 11.033223] ath11k: probe of c000000.wifi failed with error -95 Fixes: 25edca7bb18a ("wifi: ath11k: add ipq5018 device support") Signed-off-by: Ziyang Huang <hzyitc@outlook.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/TYZPR01MB5556D7AA10ABEDDDD2D8F39EC953A@TYZPR01MB5556.apcprd01.prod.exchangelabs.com 
Without this patch, the IPQ5018 WiFi will fail and print the following
logs:

	[   11.033179] ath11k c000000.wifi: unsupported device type 7
	[   11.033223] ath11k: probe of c000000.wifi failed with error -95

Fixes: 25edca7bb18a ("wifi: ath11k: add ipq5018 device support")
Signed-off-by: Ziyang Huang <hzyitc@outlook.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/TYZPR01MB5556D7AA10ABEDDDD2D8F39EC953A@TYZPR01MB5556.apcprd01.prod.exchangelabs.com
wifi: ath11k: Add missing check for ioremap 2023-06-15T11:39:49+00:00 Jiasheng Jiang jiasheng@iscas.ac.cn 2023-06-13T09:19:40+00:00 16e0077e14a73866e9b0f4a6bf4ad3d4a5cb0f2a Add check for ioremap() and return the error if it fails in order to guarantee the success of ioremap(), same as in ath11k_qmi_load_file_target_mem(). Fixes: 6ac04bdc5edb ("ath11k: Use reserved host DDR addresses from DT for PCI devices") Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20230608022858.27405-1-jiasheng@iscas.ac.cn 
Add check for ioremap() and return the error if it fails in order to
guarantee the success of ioremap(), same as in
ath11k_qmi_load_file_target_mem().

Fixes: 6ac04bdc5edb ("ath11k: Use reserved host DDR addresses from DT for PCI devices")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230608022858.27405-1-jiasheng@iscas.ac.cn