linux.git/drivers/net/usb, branch v6.7-rc7

net: usb: ax88179_178a: avoid failed operations when device is disconnected

2023-12-15T13:00:03+00:00

When the device is disconnected we get the following messages showing
failed operations:
Nov 28 20:22:11 localhost kernel: usb 2-3: USB disconnect, device number 2
Nov 28 20:22:11 localhost kernel: ax88179_178a 2-3:1.0 enp2s0u3: unregister 'ax88179_178a' usb-0000:02:00.0-3, ASIX AX88179 USB 3.0 Gigabit Ethernet
Nov 28 20:22:11 localhost kernel: ax88179_178a 2-3:1.0 enp2s0u3: Failed to read reg index 0x0002: -19
Nov 28 20:22:11 localhost kernel: ax88179_178a 2-3:1.0 enp2s0u3: Failed to write reg index 0x0002: -19
Nov 28 20:22:11 localhost kernel: ax88179_178a 2-3:1.0 enp2s0u3 (unregistered): Failed to write reg index 0x0002: -19
Nov 28 20:22:11 localhost kernel: ax88179_178a 2-3:1.0 enp2s0u3 (unregistered): Failed to write reg index 0x0001: -19
Nov 28 20:22:11 localhost kernel: ax88179_178a 2-3:1.0 enp2s0u3 (unregistered): Failed to write reg index 0x0002: -19

The reason is that although the device is detached, normal stop and
unbind operations are commanded from the driver. These operations are
not necessary in this situation, so avoid these logs when the device is
detached if the result of the operation is -ENODEV and if the new flag
informing about the disconnecting status is enabled.

cc:  
Fixes: e2ca90c276e1f ("ax88179_178a: ASIX AX88179_178A USB 3.0/2.0 to gigabit ethernet adapter driver")
Signed-off-by: Jose Ignacio Tornos Martinez 
Acked-by: Alan Stern 
Link: https://lore.kernel.org/r/20231207175007.263907-1-jtornosm@redhat.com
Signed-off-by: Greg Kroah-Hartman

r8152: add vendor/device ID pair for ASUS USB-C2500

2023-12-06T09:38:38+00:00

The ASUS USB-C2500 is an RTL8156 based 2.5G Ethernet controller.

Add the vendor and product ID values to the driver. This makes Ethernet
work with the adapter.

Signed-off-by: Kelly Kane 
Link: https://lore.kernel.org/r/20231203011712.6314-1-kelly@hawknetworks.com
Signed-off-by: Paolo Abeni

r8152: Add RTL8152_INACCESSIBLE to r8153_aldps_en()

2023-12-04T12:22:01+00:00

Delay loops in r8152 should break out if RTL8152_INACCESSIBLE is set
so that they don't delay too long if the device becomes
inaccessible. Add the break to the loop in r8153_aldps_en().

Fixes: 4214cc550bf9 ("r8152: check if disabling ALDPS is finished")
Reviewed-by: Grant Grundler 
Signed-off-by: Douglas Anderson 
Acked-by: Hayes Wang 
Signed-off-by: David S. Miller

r8152: Add RTL8152_INACCESSIBLE to r8153_pre_firmware_1()

2023-12-04T12:22:01+00:00

Delay loops in r8152 should break out if RTL8152_INACCESSIBLE is set
so that they don't delay too long if the device becomes
inaccessible. Add the break to the loop in r8153_pre_firmware_1().

Fixes: 9370f2d05a2a ("r8152: support request_firmware for RTL8153")
Reviewed-by: Grant Grundler 
Signed-off-by: Douglas Anderson 
Acked-by: Hayes Wang 
Signed-off-by: David S. Miller

r8152: Add RTL8152_INACCESSIBLE to r8156b_wait_loading_flash()

2023-12-04T12:22:01+00:00

Delay loops in r8152 should break out if RTL8152_INACCESSIBLE is set
so that they don't delay too long if the device becomes
inaccessible. Add the break to the loop in
r8156b_wait_loading_flash().

Fixes: 195aae321c82 ("r8152: support new chips")
Reviewed-by: Grant Grundler 
Signed-off-by: Douglas Anderson 
Acked-by: Hayes Wang 
Signed-off-by: David S. Miller

r8152: Add RTL8152_INACCESSIBLE checks to more loops

2023-12-04T12:22:01+00:00

Previous commits added checks for RTL8152_INACCESSIBLE in the loops in
the driver. There are still a few more that keep tripping the driver
up in error cases and make things take longer than they should. Add
those in.

All the loops that are part of this commit existed in some form or
another since the r8152 driver was first introduced, though
RTL8152_INACCESSIBLE was known as RTL8152_UNPLUG before commit
715f67f33af4 ("r8152: Rename RTL8152_UNPLUG to RTL8152_INACCESSIBLE")

Fixes: ac718b69301c ("net/usb: new driver for RTL8152")
Reviewed-by: Grant Grundler 
Signed-off-by: Douglas Anderson 
Acked-by: Hayes Wang 
Signed-off-by: David S. Miller

r8152: Hold the rtnl_lock for all of reset

2023-12-04T12:22:01+00:00

As of commit d9962b0d4202 ("r8152: Block future register access if
register access fails") there is a race condition that can happen
between the USB device reset thread and napi_enable() (not) getting
called during rtl8152_open(). Specifically:
* While rtl8152_open() is running we get a register access error
  that's _not_ -ENODEV and queue up a USB reset.
* rtl8152_open() exits before calling napi_enable() due to any reason
  (including usb_submit_urb() returning an error).

In that case:
* Since the USB reset is perform in a separate thread asynchronously,
  it can run at anytime USB device lock is not held - even before
  rtl8152_open() has exited with an error and caused __dev_open() to
  clear the __LINK_STATE_START bit.
* The rtl8152_pre_reset() will notice that the netif_running() returns
  true (since __LINK_STATE_START wasn't cleared) so it won't exit
  early.
* rtl8152_pre_reset() will then hang in napi_disable() because
  napi_enable() was never called.

We can fix the race by making sure that the r8152 reset routines don't
run at the same time as we're opening the device. Specifically we need
the reset routines in their entirety rely on the return value of
netif_running(). The only way to reliably depend on that is for them
to hold the rntl_lock() mutex for the duration of reset.

Grabbing the rntl_lock() mutex for the duration of reset seems like a
long time, but reset is not expected to be common and the rtnl_lock()
mutex is already held for long durations since the core grabs it
around the open/close calls.

Fixes: d9962b0d4202 ("r8152: Block future register access if register access fails")
Reviewed-by: Grant Grundler 
Signed-off-by: Douglas Anderson 
Signed-off-by: David S. Miller

net: usb: qmi_wwan: claim interface 4 for ZTE MF290

2023-11-23T08:30:27+00:00

Interface 4 is used by for QMI interface in stock firmware of MF28D, the
router which uses MF290 modem. Rebind it to qmi_wwan after freeing it up
from option driver.
The proper configuration is:

Interface mapping is:
0: QCDM, 1: (unknown), 2: AT (PCUI), 2: AT (Modem), 4: QMI

T:  Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=  4 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=19d2 ProdID=0189 Rev= 0.00
S:  Manufacturer=ZTE, Incorporated
S:  Product=ZTE LTE Technologies MSM
C:* #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=84(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E:  Ad=86(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms

Cc: Bjørn Mork 
Signed-off-by: Lech Perczak 
Link: https://lore.kernel.org/r/20231117231918.100278-3-lech.perczak@gmail.com
Signed-off-by: Paolo Abeni

net: usb: ax88179_178a: fix failed operations during ax88179_reset

2023-11-21T22:34:08+00:00

Using generic ASIX Electronics Corp. AX88179 Gigabit Ethernet device,
the following test cycle has been implemented:
    - power on
    - check logs
    - shutdown
    - after detecting the system shutdown, disconnect power
    - after approximately 60 seconds of sleep, power is restored
Running some cycles, sometimes error logs like this appear:
    kernel: ax88179_178a 2-9:1.0 (unnamed net_device) (uninitialized): Failed to write reg index 0x0001: -19
    kernel: ax88179_178a 2-9:1.0 (unnamed net_device) (uninitialized): Failed to read reg index 0x0001: -19
    ...
These failed operation are happening during ax88179_reset execution, so
the initialization could not be correct.

In order to avoid this, we need to increase the delay after reset and
clock initial operations. By using these larger values, many cycles
have been run and no failed operations appear.

It would be better to check some status register to verify when the
operation has finished, but I do not have found any available information
(neither in the public datasheets nor in the manufacturer's driver). The
only available information for the necessary delays is the maufacturer's
driver (original values) but the proposed values are not enough for the
tested devices.

Fixes: e2ca90c276e1f ("ax88179_178a: ASIX AX88179_178A USB 3.0/2.0 to gigabit ethernet adapter driver")
Reported-by: Herb Wei 
Tested-by: Herb Wei 
Signed-off-by: Jose Ignacio Tornos Martinez 
Link: https://lore.kernel.org/r/20231120120642.54334-1-jtornosm@redhat.com
Signed-off-by: Jakub Kicinski

usb: aqc111: check packet for fixup for true limit

2023-11-16T23:39:13+00:00

If a device sends a packet that is inbetween 0
and sizeof(u64) the value passed to skb_trim()
as length will wrap around ending up as some very
large value.

The driver will then proceed to parse the header
located at that position, which will either oops or
process some random value.

The fix is to check against sizeof(u64) rather than
0, which the driver currently does. The issue exists
since the introduction of the driver.

Signed-off-by: Oliver Neukum 
Signed-off-by: David S. Miller