There are 2 models for MV32 serials. MV32-W-A is designed
based on Qualcomm SDX62 chip, and MV32-W-B is designed based
on Qualcomm SDX65 chip. So we use 2 different PID to separate it.

Test evidence as below:
T:  Bus=03 Lev=01 Prnt=01 Port=02 Cnt=03 Dev#=  3 Spd=480 MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=1e2d ProdID=00f3 Rev=05.04
S:  Manufacturer=Cinterion
S:  Product=Cinterion PID 0x00F3 USB Mobile Broadband
S:  SerialNumber=d7b4be8d
C:  #Ifs= 4 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#=0x0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
I:  If#=0x1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
I:  If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
I:  If#=0x3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option

T:  Bus=03 Lev=01 Prnt=01 Port=02 Cnt=03 Dev#= 10 Spd=480 MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=1e2d ProdID=00f4 Rev=05.04
S:  Manufacturer=Cinterion
S:  Product=Cinterion PID 0x00F4 USB Mobile Broadband
S:  SerialNumber=d095087d
C:  #Ifs= 4 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#=0x0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
I:  If#=0x1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
I:  If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
I:  If#=0x3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option

Signed-off-by: Slark Xiao <slark_xiao@163.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Link: https://lore.kernel.org/r/20220810014521.9383-1-slark_xiao@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This reverts commit 36a15e1cb134c0395261ba1940762703f778438c.

The usage of FLAG_SEND_ZLP causes problems to other firmware/hardware
versions that have no issues.

The FLAG_SEND_ZLP is not safe to use in this context.
See:
https://patchwork.ozlabs.org/project/netdev/patch/1270599787.8900.8.camel@Linuxdev4-laptop/#118378
The original problem needs another way to solve.

Fixes: 36a15e1cb134 ("net: usb: ax88179_178a needs FLAG_SEND_ZLP")
Cc: stable@vger.kernel.org
Reported-by: Ronald Wahl <ronald.wahl@raritan.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216327
Link: https://bugs.archlinux.org/task/75491
Signed-off-by: Jose Alonso <joalonsof@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:

net/ax25/af_ax25.c
  d7c4c9e075f8c ("ax25: fix incorrect dev_tracker usage")
  d62607c3fe459 ("net: rename reference+tracking helpers")

drivers/net/netdevsim/fib.c
  180a6a3ee60a ("netdevsim: fib: Fix reference count leak on route deletion failure")
  012ec02ae441 ("netdevsim: convert driver to use unlocked devlink API during init/fini")

Signed-off-by: Paolo Abeni <pabeni@redhat.com>

The Anker PowerExpand USB-C to Gigabit Ethernet adapter uses this
chipset, but exposes CDC Ethernet configurations as well as the
vendor specific one. This driver tries to bind by PID:VID
unconditionally and ends up picking up the CDC configuration, which
is supposed to be handled by the class driver. To make things even
more confusing, it sees both of the CDC class interfaces and tries
to bind twice, resulting in two broken Ethernet devices.

Change all the ID matches to specifically match the vendor-specific
interface. By default the device comes up in CDC mode and is bound by
that driver (which works fine); users may switch it to the vendor
interface using sysfs to set bConfigurationValue, at which point the
device actually goes through a reconnect cycle and comes back as a
vendor specific only device, and then this driver binds and works too.

The affected device uses VID/PID 0b95:1790, but we might as well change
all of them for good measure, since there is no good reason for this
driver to bind to standard CDC Ethernet interfaces.

v3: Added VID/PID info to commit message

Signed-off-by: Hector Martin <marcan@marcan.st>
Link: https://lore.kernel.org/r/20220731072209.45504-1-marcan@marcan.st
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

This refixes:

    commit 7da17624e7948d5d9660b910f8079d26d26ce453
    nt: usb: USB_RTL8153_ECM should not default to y

    In general, device drivers should not be enabled by default.

which basically broke the commit it claimed to fix, ie:

    commit 657bc1d10bfc23ac06d5d687ce45826c760744f9
    r8153_ecm: avoid to be prior to r8152 driver

    Avoid r8153_ecm is compiled as built-in, if r8152 driver is compiled
    as modules. Otherwise, the r8153_ecm would be used, even though the
    device is supported by r8152 driver.

this commit amounted to:

drivers/net/usb/Kconfig:

+config USB_RTL8153_ECM
+       tristate "RTL8153 ECM support"
+       depends on USB_NET_CDCETHER && (USB_RTL8152 || USB_RTL8152=n)
+       default y
+       help
+         This option supports ECM mode for RTL8153 ethernet adapter, when
+         CONFIG_USB_RTL8152 is not set, or the RTL8153 device is not
+         supported by r8152 driver.

drivers/net/usb/Makefile:

-obj-$(CONFIG_USB_NET_CDCETHER) += cdc_ether.o r8153_ecm.o
+obj-$(CONFIG_USB_NET_CDCETHER) += cdc_ether.o
+obj-$(CONFIG_USB_RTL8153_ECM)  += r8153_ecm.o

And as can be seen it pulls a piece of the cdc_ether driver out into
a separate config option to be able to make this piece modular in case
cdc_ether is builtin, while r8152 is modular.

While in general, device drivers should indeed not be enabled by default:
this isn't a device driver per say, but rather this is support code for
the CDCETHER (ECM) driver, and should thus be enabled if it is enabled.

See also email thread at:
  https://www.spinics.net/lists/netdev/msg767649.html

In:
  https://www.spinics.net/lists/netdev/msg768284.html

Jakub wrote:
  And when we say "removed" we can just hide it from what's prompted
  to the user (whatever such internal options are called)? I believe
  this way we don't bring back Marek's complaint.

Side note: these incorrect defaults will result in Android 13
on 5.15 GKI kernels lacking USB_RTL8153_ECM support while having
USB_NET_CDCETHER (luckily we also have USB_RTL8150 and USB_RTL8152,
so it's probably only an issue for very new RTL815x hardware with
no native 5.15 driver).

Fixes: 7da17624e7948d5d ("nt: usb: USB_RTL8153_ECM should not default to y")
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Hayes Wang <hayeswang@realtek.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20220730230113.4138858-1-zenczykowski@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

delete extra space and tab in blank line, there is no functional change.

Signed-off-by: Xie Shaowen <studentxswpy@163.com>
Link: https://lore.kernel.org/r/20220727081253.3043941-1-studentxswpy@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

- Check if wol is supported on reset instead of everytime get_wol
is called.
- Save wolopts in private data instead of relying on the HW to save it.
- Defer enabling WoL until suspend instead of enabling it everytime
set_wol is called.

Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

We need more space to save WoL context. So lets allocate memory
for ax88179_data instead of using struct usbnet data field which
only supports 5 words. We continue to use the struct usbnet data
field for multicast filters. However since we no longer have the
private data stored there, we can shift it to the beginning.

Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The hardware state was only partially restored, which meant certain
functionality was broken on resume. Do a full HW reset on resume to
fix this.

Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Instead of passing in_pm flags all over the place, use the private
struct to handle in_pm mode.

Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>