This fixes that the platform is waked by an unexpected packet. The
size and range of FIFO is different when the device enters S3 state,
so it is necessary to correct some settings when suspending.
Regardless of jumbo frame, set RMS to 1522 and MTPS to MTPS_DEFAULT.
Besides, enable MCU_BORW_EN to update the method of calculating the
pointer of data. Then, the hardware could get the correct data.
Fixes: 195aae321c82 ("r8152: support new chips")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/20220718082120.10957-391-nic_swsd@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A warning is triggered by commit 66e4c8d95008 ("net: warn if transport
header was not set"). The warning is harmless, because the value from
skb_transport_offset() is only used for skb_is_gso() is true or the
skb->ip_summed is equal to CHECKSUM_PARTIAL.
Fixes: 66e4c8d95008 ("net: warn if transport header was not set")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
usbnet_write_cmd_async() mixed up which buffers
need to be freed in which error case.
v2: add Fixes tag
v3: fix uninitialized buf pointer
Fixes: 877bd862f32b8 ("usbnet: introduce usbnet 3 command helpers")
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20220705125351.17309-1-oneukum@suse.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove the repeated ';' from code. Signed-off-by: Li kunyu <kunyu@nfschina.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch corrects packet receiving in ax88179_rx_fixup.
- problem observed:
ifconfig shows allways a lot of 'RX Errors' while packets
are received normally.
This occurs because ax88179_rx_fixup does not recognise properly
the usb urb received.
The packets are normally processed and at the end, the code exits
with 'return 0', generating RX Errors.
(pkt_cnt==-2 and ptk_hdr over field rx_hdr trying to identify
another packet there)
This is a usb urb received by "tcpdump -i usbmon2 -X" on a
little-endian CPU:
0x0000: eeee f8e3 3b19 87a0 94de 80e3 daac 0800
^ packet 1 start (pkt_len = 0x05ec)
^^^^ IP alignment pseudo header
^ ethernet packet start
last byte ethernet packet v
padding (8-bytes aligned) vvvv vvvv
0x05e0: c92d d444 1420 8a69 83dd 272f e82b 9811
0x05f0: eeee f8e3 3b19 87a0 94de 80e3 daac 0800
... ^ packet 2
0x0be0: eeee f8e3 3b19 87a0 94de 80e3 daac 0800
...
0x1130: 9d41 9171 8a38 0ec5 eeee f8e3 3b19 87a0
...
0x1720: 8cfc 15ff 5e4c e85c eeee f8e3 3b19 87a0
...
0x1d10: ecfa 2a3a 19ab c78c eeee f8e3 3b19 87a0
...
0x2070: eeee f8e3 3b19 87a0 94de 80e3 daac 0800
... ^ packet 7
0x2120: 7c88 4ca5 5c57 7dcc 0d34 7577 f778 7e0a
0x2130: f032 e093 7489 0740 3008 ec05 0000 0080
====1==== ====2====
hdr_off ^
pkt_len = 0x05ec ^^^^
AX_RXHDR_*=0x00830 ^^^^ ^
pkt_len = 0 ^^^^
AX_RXHDR_DROP_ERR=0x80000000 ^^^^ ^
0x2140: 3008 ec05 0000 0080 3008 5805 0000 0080
0x2150: 3008 ec05 0000 0080 3008 ec05 0000 0080
0x2160: 3008 5803 0000 0080 3008 c800 0000 0080
===11==== ===12==== ===13==== ===14====
0x2170: 0000 0000 0e00 3821
^^^^ ^^^^ rx_hdr
^^^^ pkt_cnt=14
^^^^ hdr_off=0x2138
^^^^ ^^^^ padding
The dump shows that pkt_cnt is the number of entrys in the
per-packet metadata. It is "2 * packet count".
Each packet have two entrys. The first have a valid
value (pkt_len and AX_RXHDR_*) and the second have a
dummy-header 0x80000000 (pkt_len=0 with AX_RXHDR_DROP_ERR).
Why exists dummy-header for each packet?!?
My guess is that this was done probably to align the
entry for each packet to 64-bits and maintain compatibility
with old firmware.
There is also a padding (0x00000000) before the rx_hdr to
align the end of rx_hdr to 64-bit.
Note that packets have a alignment of 64-bits (8-bytes).
This patch assumes that the dummy-header and the last
padding are optional. So it preserves semantics and
recognises the same valid packets as the current code.
This patch was made using only the dumpfile information and
tested with only one device:
0b95:1790 ASIX Electronics Corp. AX88179 Gigabit Ethernet
Fixes: 57bc3d3ae8c1 ("net: usb: ax88179_178a: Fix out-of-bounds accesses in RX fixup")
Fixes: e2ca90c276e1 ("ax88179_178a: ASIX AX88179_178A USB 3.0/2.0 to gigabit ethernet adapter driver")
Signed-off-by: Jose Alonso <joalonsof@gmail.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/d6970bb04bf67598af4d316eaeb1792040b18cfd.camel@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
usbnet provides some helper functions that are also used in
the context of reset() operations. During a reset the other
drivers on a device are unable to operate. As that can be block
drivers, a driver for another interface cannot use paging
in its memory allocations without risking a deadlock.
Use GFP_NOIO in the helpers.
Fixes: 877bd862f32b8 ("usbnet: introduce usbnet 3 command helpers")
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20220628093517.7469-1-oneukum@suse.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We should respect link partner capabilities and not force flow control
support on every link. Even more, in current state the MAC driver do not
advertises pause support so we should not keep flow control enabled at
all.
Fixes: e532a096be0e ("net: usb: asix: ax88772: add phylib support")
Reported-by: Anton Lundin <glance@acc.umu.se>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Tested-by: Anton Lundin <glance@acc.umu.se>
Link: https://lore.kernel.org/r/20220624075139.3139300-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If cable is attached after probe sequence, the usbnet framework would
not automatically start processing RX packets except at least one
packet was transmitted.
On systems with any kind of address auto configuration this issue was
not detected, because some packets are send immediately after link state
is changed to "running".
With this patch we will notify usbnet about link status change provided by the
PHYlib.
Fixes: e532a096be0e ("net: usb: asix: ax88772: add phylib support")
Reported-by: Anton Lundin <glance@acc.umu.se>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Tested-by: Anton Lundin <glance@acc.umu.se>
Link: https://lore.kernel.org/r/20220624075139.3139300-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The extra byte inserted by usbnet.c when
(length % dev->maxpacket == 0) is causing problems to device.
This patch sets FLAG_SEND_ZLP to avoid this.
Tested with: 0b95:1790 ASIX Electronics Corp. AX88179 Gigabit Ethernet
Problems observed:
======================================================================
1) Using ssh/sshfs. The remote sshd daemon can abort with the message:
"message authentication code incorrect"
This happens because the tcp message sent is corrupted during the
USB "Bulk out". The device calculate the tcp checksum and send a
valid tcp message to the remote sshd. Then the encryption detects
the error and aborts.
2) NETDEV WATCHDOG: ... (ax88179_178a): transmit queue 0 timed out
3) Stop normal work without any log message.
The "Bulk in" continue receiving packets normally.
The host sends "Bulk out" and the device responds with -ECONNRESET.
(The netusb.c code tx_complete ignore -ECONNRESET)
Under normal conditions these errors take days to happen and in
intense usage take hours.
A test with ping gives packet loss, showing that something is wrong:
ping -4 -s 462 {destination} # 462 = 512 - 42 - 8
Not all packets fail.
My guess is that the device tries to find another packet starting
at the extra byte and will fail or not depending on the next
bytes (old buffer content).
======================================================================
Signed-off-by: Jose Alonso <joalonsof@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull USB / Thunderbolt updates from Greg KH:
"Here is the "big" set of USB and Thunderbolt driver changes for
5.18-rc1. For the most part it's been a quiet development cycle for
the USB core, but there are the usual "hot spots" of development
activity.
Included in here are:
- Thunderbolt driver updates:
- fixes for devices without displayport adapters
- lane bonding support and improvements
- other minor changes based on device testing
- dwc3 gadget driver changes.
It seems this driver will never be finished given that the IP core
is showing up in zillions of new devices and each implementation
decides to do something different with it...
- uvc gadget driver updates as more devices start to use and rely on
this hardware as well
- usb_maxpacket() api changes to remove an unneeded and unused
parameter.
- usb-serial driver device id updates and small cleanups
- typec cleanups and fixes based on device testing
- device tree updates for usb properties
- lots of other small fixes and driver updates.
All of these have been in linux-next for weeks with no reported
problems"
* tag 'usb-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (154 commits)
USB: new quirk for Dell Gen 2 devices
usb: dwc3: core: Add error log when core soft reset failed
usb: dwc3: gadget: Move null pinter check to proper place
usb: hub: Simplify error and success path in port_over_current_notify
usb: cdns3: allocate TX FIFO size according to composite EP number
usb: dwc3: Fix ep0 handling when getting reset while doing control transfer
usb: Probe EHCI, OHCI controllers asynchronously
usb: isp1760: Fix out-of-bounds array access
xhci: Don't defer primary roothub registration if there is only one roothub
USB: serial: option: add Quectel BG95 modem
USB: serial: pl2303: fix type detection for odd device
xhci: Allow host runtime PM as default for Intel Alder Lake N xHCI
xhci: Remove quirk for over 10 year old evaluation hardware
xhci: prevent U2 link power state if Intel tier policy prevented U1
xhci: use generic command timer for stop endpoint commands.
usb: host: xhci-plat: omit shared hcd if either root hub has no ports
usb: host: xhci-plat: prepare operation w/o shared hcd
usb: host: xhci-plat: create shared hcd after having added main hcd
xhci: prepare for operation w/o shared hcd
xhci: factor out parts of xhci_gen_setup()
...