linux.git/drivers/net/phy, branch v6.5-rc4 Linux kernel source tree net: phy: marvell10g: fix 88x3310 power up 2023-07-23T10:47:07+00:00 Jiawen Wu jiawenwu@trustnetic.com 2023-07-19T09:22:33+00:00 c7b75bea853daeb64fc831dbf39a6bbabcc402ac Clear MV_V2_PORT_CTRL_PWRDOWN bit to set power up for 88x3310 PHY, it sometimes does not take effect immediately. And a read of this register causes the bit not to clear. This will cause mv3310_reset() to time out, which will fail the config initialization. So add a delay before the next access. Fixes: c9cc1c815d36 ("net: phy: marvell10g: place in powersave mode at probe") Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> 
Clear MV_V2_PORT_CTRL_PWRDOWN bit to set power up for 88x3310 PHY,
it sometimes does not take effect immediately. And a read of this
register causes the bit not to clear. This will cause mv3310_reset()
to time out, which will fail the config initialization. So add a delay
before the next access.

Fixes: c9cc1c815d36 ("net: phy: marvell10g: place in powersave mode at probe")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
net: phy: prevent stale pointer dereference in phy_init() 2023-07-20T19:47:25+00:00 Vladimir Oltean vladimir.oltean@nxp.com 2023-07-20T00:02:31+00:00 1c613beaf877c0c0d755853dc62687e2013e55c4 mdio_bus_init() and phy_driver_register() both have error paths, and if those are ever hit, ethtool will have a stale pointer to the phy_ethtool_phy_ops stub structure, which references memory from a module that failed to load (phylib). It is probably hard to force an error in this code path even manually, but the error teardown path of phy_init() should be the same as phy_exit(), which is now simply not the case. Fixes: 55d8f053ce1b ("net: phy: Register ethtool PHY operations") Link: https://lore.kernel.org/netdev/ZLaiJ4G6TaJYGJyU@shell.armlinux.org.uk/ Suggested-by: Russell King (Oracle) <linux@armlinux.org.uk> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://lore.kernel.org/r/20230720000231.1939689-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> 
mdio_bus_init() and phy_driver_register() both have error paths, and if
those are ever hit, ethtool will have a stale pointer to the
phy_ethtool_phy_ops stub structure, which references memory from a
module that failed to load (phylib).

It is probably hard to force an error in this code path even manually,
but the error teardown path of phy_init() should be the same as
phy_exit(), which is now simply not the case.

Fixes: 55d8f053ce1b ("net: phy: Register ethtool PHY operations")
Link: https://lore.kernel.org/netdev/ZLaiJ4G6TaJYGJyU@shell.armlinux.org.uk/
Suggested-by: Russell King (Oracle) <linux@armlinux.org.uk>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20230720000231.1939689-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net 2023-06-27T16:45:22+00:00 Jakub Kicinski kuba@kernel.org 2023-06-27T16:45:22+00:00 3674fbf0451df0395f9fa18df3122927006a3829 Merge in late fixes to prepare for the 6.5 net-next PR. Signed-off-by: Jakub Kicinski <kuba@kernel.org> 
Merge in late fixes to prepare for the 6.5 net-next PR.

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net: phy: mscc: fix packet loss due to RGMII delays 2023-06-27T16:31:51+00:00 Vladimir Oltean vladimir.oltean@nxp.com 2023-06-27T13:42:35+00:00 528a08bcd820d07887edeae706df88ceb06db109 Two deadly typos break RX and TX traffic on the VSC8502 PHY using RGMII if phy-mode = "rgmii-id" or "rgmii-txid", and no "tx-internal-delay-ps" override exists. The negative error code from phy_get_internal_delay() does not get overridden with the delay deduced from the phy-mode, and later gets committed to hardware. Also, the rx_delay gets overridden by what should have been the tx_delay. Fixes: dbb050d2bfc8 ("phy: mscc: Add support for RGMII delay configuration") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Harini Katakam <harini.katakam@amd.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Link: https://lore.kernel.org/r/20230627134235.3453358-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> 
Two deadly typos break RX and TX traffic on the VSC8502 PHY using RGMII
if phy-mode = "rgmii-id" or "rgmii-txid", and no "tx-internal-delay-ps"
override exists. The negative error code from phy_get_internal_delay()
does not get overridden with the delay deduced from the phy-mode, and
later gets committed to hardware. Also, the rx_delay gets overridden by
what should have been the tx_delay.

Fixes: dbb050d2bfc8 ("phy: mscc: Add support for RGMII delay configuration")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Harini Katakam <harini.katakam@amd.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230627134235.3453358-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net: phy: broadcom: drop brcm_phy_setbits() and use phy_set_bits() instead 2023-06-24T22:05:40+00:00 Giulio Benetti giulio.benetti@benettiengineering.com 2023-06-22T18:47:21+00:00 28e219aea0b9ec374de27179c3d45b2d86bfe562 Linux provides phy_set_bits() helper so let's drop brcm_phy_setbits() and use phy_set_bits() in its place. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Link: https://lore.kernel.org/r/20230622184721.24368-1-giulio.benetti@benettiengineering.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> 
Linux provides phy_set_bits() helper so let's drop brcm_phy_setbits() and
use phy_set_bits() in its place.

Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230622184721.24368-1-giulio.benetti@benettiengineering.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net: phy: dp83td510: fix kernel stall during netboot in DP83TD510E PHY driver 2023-06-23T02:43:55+00:00 Oleksij Rempel o.rempel@pengutronix.de 2023-06-21T04:38:48+00:00 fc0649395dca81f2b3b02d9b248acb38cbcee55c Fix an issue where the kernel would stall during netboot, showing the "sched: RT throttling activated" message. This stall was triggered by the behavior of the mii_interrupt bit (Bit 7 - DP83TD510E_STS_MII_INT) in the DP83TD510E's PHY_STS Register (Address = 0x10). The DP83TD510E datasheet (2020) states that the bit clears on write, however, in practice, the bit clears on read. This discrepancy had significant implications on the driver's interrupt handling. The PHY_STS Register was used by handle_interrupt() to check for pending interrupts and by read_status() to get the current link status. The call to read_status() was unintentionally clearing the mii_interrupt status bit without deasserting the IRQ pin, causing handle_interrupt() to miss other pending interrupts. This issue was most apparent during netboot. The fix refrains from using the PHY_STS Register for interrupt handling. Instead, we now solely rely on the INTERRUPT_REG_1 Register (Address = 0x12) and INTERRUPT_REG_2 Register (Address = 0x13) for this purpose. These registers directly influence the IRQ pin state and are latched high until read. Note: The INTERRUPT_REG_2 Register (Address = 0x13) exists and can also be used for interrupt handling, specifically for "Aneg page received interrupt" and "Polarity change interrupt". However, these features are currently not supported by this driver. Fixes: 165cd04fe253 ("net: phy: dp83td510: Add support for the DP83TD510 Ethernet PHY") Cc: <stable@vger.kernel.org> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20230621043848.3806124-1-o.rempel@pengutronix.de Signed-off-by: Jakub Kicinski <kuba@kernel.org> 
Fix an issue where the kernel would stall during netboot, showing the
"sched: RT throttling activated" message. This stall was triggered by
the behavior of the mii_interrupt bit (Bit 7 - DP83TD510E_STS_MII_INT)
in the DP83TD510E's PHY_STS Register (Address = 0x10). The DP83TD510E
datasheet (2020) states that the bit clears on write, however, in
practice, the bit clears on read.

This discrepancy had significant implications on the driver's interrupt
handling. The PHY_STS Register was used by handle_interrupt() to check
for pending interrupts and by read_status() to get the current link
status. The call to read_status() was unintentionally clearing the
mii_interrupt status bit without deasserting the IRQ pin, causing
handle_interrupt() to miss other pending interrupts. This issue was most
apparent during netboot.

The fix refrains from using the PHY_STS Register for interrupt handling.
Instead, we now solely rely on the INTERRUPT_REG_1 Register (Address =
0x12) and INTERRUPT_REG_2 Register (Address = 0x13) for this purpose.
These registers directly influence the IRQ pin state and are latched
high until read.

Note: The INTERRUPT_REG_2 Register (Address = 0x13) exists and can also
be used for interrupt handling, specifically for "Aneg page received
interrupt" and "Polarity change interrupt". However, these features are
currently not supported by this driver.

Fixes: 165cd04fe253 ("net: phy: dp83td510: Add support for the DP83TD510 Ethernet PHY")
Cc: <stable@vger.kernel.org>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230621043848.3806124-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net: phylink: pass neg_mode into phylink_mii_c22_pcs_config() 2023-06-23T02:41:01+00:00 Russell King (Oracle) rmk+kernel@armlinux.org.uk 2023-06-16T12:06:32+00:00 febf2aaf05641f3258cc30e072aff65cffc7c82c Convert fman_dtsec, xilinx_axienet and pcs-lynx to pass the neg_mode into phylink_mii_c22_pcs_config(). Where appropriate, drivers are updated to have neg_mode passed into their pcs_config() and pcs_link_up() functions. For other drivers, we just hoist the call to phylink_pcs_neg_mode() to their pcs_config() method out of phylink_mii_c22_pcs_config(). Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://lore.kernel.org/r/E1qA8Do-00EaFM-Ra@rmk-PC.armlinux.org.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org> 
Convert fman_dtsec, xilinx_axienet and pcs-lynx to pass the neg_mode
into phylink_mii_c22_pcs_config(). Where appropriate, drivers are
updated to have neg_mode passed into their pcs_config() and
pcs_link_up() functions. For other drivers, we just hoist the call
to phylink_pcs_neg_mode() to their pcs_config() method out of
phylink_mii_c22_pcs_config().

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8Do-00EaFM-Ra@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net: phylink: convert phylink_mii_c22_pcs_config() to neg_mode 2023-06-23T02:41:01+00:00 Russell King (Oracle) rmk+kernel@armlinux.org.uk 2023-06-16T12:06:27+00:00 cdb08aa0473730315dbc088d5394e59622314034 Use phylink_pcs_neg_mode() for phylink_mii_c22_pcs_config(). This results in no functional change. Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://lore.kernel.org/r/E1qA8Dj-00EaFG-Mt@rmk-PC.armlinux.org.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org> 
Use phylink_pcs_neg_mode() for phylink_mii_c22_pcs_config(). This
results in no functional change.

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8Dj-00EaFG-Mt@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net: phylink: add PCS negotiation mode 2023-06-23T02:41:01+00:00 Russell King (Oracle) rmk+kernel@armlinux.org.uk 2023-06-16T12:06:22+00:00 f99d471afa03f770149f1cc60a288b9a08285903 PCS have to work out whether they should enable PCS negotiation by looking at the "mode" and "interface" arguments, and the Autoneg bit in the advertising mask. This leads to some complex logic, so lets pull that out into phylink and instead pass a "neg_mode" argument to the PCS configuration and link up methods, instead of the "mode" argument. In order to transition drivers, add a "neg_mode" flag to the phylink PCS structure to PCS can indicate whether they want to be passed the neg_mode or the old mode argument. Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://lore.kernel.org/r/E1qA8De-00EaFA-Ht@rmk-PC.armlinux.org.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org> 
PCS have to work out whether they should enable PCS negotiation by
looking at the "mode" and "interface" arguments, and the Autoneg bit
in the advertising mask.

This leads to some complex logic, so lets pull that out into phylink
and instead pass a "neg_mode" argument to the PCS configuration and
link up methods, instead of the "mode" argument.

In order to transition drivers, add a "neg_mode" flag to the phylink
PCS structure to PCS can indicate whether they want to be passed the
neg_mode or the old mode argument.

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8De-00EaFA-Ht@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net 2023-06-23T01:40:38+00:00 Jakub Kicinski kuba@kernel.org 2023-06-23T01:40:38+00:00 a7384f3918756c193e3fcd7e3111fc4bd3686013 Cross-merge networking fixes after downstream PR. Conflicts: tools/testing/selftests/net/fcnal-test.sh d7a2fc1437f7 ("selftests: net: fcnal-test: check if FIPS mode is enabled") dd017c72dde6 ("selftests: fcnal: Test SO_DONTROUTE on TCP sockets.") https://lore.kernel.org/all/5007b52c-dd16-dbf6-8d64-b9701bfa498b@tessares.net/ https://lore.kernel.org/all/20230619105427.4a0df9b3@canb.auug.org.au/ No adjacent changes. Signed-off-by: Jakub Kicinski <kuba@kernel.org> 
Cross-merge networking fixes after downstream PR.

Conflicts:

tools/testing/selftests/net/fcnal-test.sh
  d7a2fc1437f7 ("selftests: net: fcnal-test: check if FIPS mode is enabled")
  dd017c72dde6 ("selftests: fcnal: Test SO_DONTROUTE on TCP sockets.")
https://lore.kernel.org/all/5007b52c-dd16-dbf6-8d64-b9701bfa498b@tessares.net/
https://lore.kernel.org/all/20230619105427.4a0df9b3@canb.auug.org.au/

No adjacent changes.

Signed-off-by: Jakub Kicinski <kuba@kernel.org>