Merge in late fixes to prepare for the 6.5 net-next PR.

Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Two deadly typos break RX and TX traffic on the VSC8502 PHY using RGMII
if phy-mode = "rgmii-id" or "rgmii-txid", and no "tx-internal-delay-ps"
override exists. The negative error code from phy_get_internal_delay()
does not get overridden with the delay deduced from the phy-mode, and
later gets committed to hardware. Also, the rx_delay gets overridden by
what should have been the tx_delay.

Fixes: dbb050d2bfc8 ("phy: mscc: Add support for RGMII delay configuration")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Harini Katakam <harini.katakam@amd.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230627134235.3453358-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Linux provides phy_set_bits() helper so let's drop brcm_phy_setbits() and
use phy_set_bits() in its place.

Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230622184721.24368-1-giulio.benetti@benettiengineering.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Fix an issue where the kernel would stall during netboot, showing the
"sched: RT throttling activated" message. This stall was triggered by
the behavior of the mii_interrupt bit (Bit 7 - DP83TD510E_STS_MII_INT)
in the DP83TD510E's PHY_STS Register (Address = 0x10). The DP83TD510E
datasheet (2020) states that the bit clears on write, however, in
practice, the bit clears on read.

This discrepancy had significant implications on the driver's interrupt
handling. The PHY_STS Register was used by handle_interrupt() to check
for pending interrupts and by read_status() to get the current link
status. The call to read_status() was unintentionally clearing the
mii_interrupt status bit without deasserting the IRQ pin, causing
handle_interrupt() to miss other pending interrupts. This issue was most
apparent during netboot.

The fix refrains from using the PHY_STS Register for interrupt handling.
Instead, we now solely rely on the INTERRUPT_REG_1 Register (Address =
0x12) and INTERRUPT_REG_2 Register (Address = 0x13) for this purpose.
These registers directly influence the IRQ pin state and are latched
high until read.

Note: The INTERRUPT_REG_2 Register (Address = 0x13) exists and can also
be used for interrupt handling, specifically for "Aneg page received
interrupt" and "Polarity change interrupt". However, these features are
currently not supported by this driver.

Fixes: 165cd04fe253 ("net: phy: dp83td510: Add support for the DP83TD510 Ethernet PHY")
Cc: <stable@vger.kernel.org>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230621043848.3806124-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Convert fman_dtsec, xilinx_axienet and pcs-lynx to pass the neg_mode
into phylink_mii_c22_pcs_config(). Where appropriate, drivers are
updated to have neg_mode passed into their pcs_config() and
pcs_link_up() functions. For other drivers, we just hoist the call
to phylink_pcs_neg_mode() to their pcs_config() method out of
phylink_mii_c22_pcs_config().

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8Do-00EaFM-Ra@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Use phylink_pcs_neg_mode() for phylink_mii_c22_pcs_config(). This
results in no functional change.

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8Dj-00EaFG-Mt@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

PCS have to work out whether they should enable PCS negotiation by
looking at the "mode" and "interface" arguments, and the Autoneg bit
in the advertising mask.

This leads to some complex logic, so lets pull that out into phylink
and instead pass a "neg_mode" argument to the PCS configuration and
link up methods, instead of the "mode" argument.

In order to transition drivers, add a "neg_mode" flag to the phylink
PCS structure to PCS can indicate whether they want to be passed the
neg_mode or the old mode argument.

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8De-00EaFA-Ht@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Cross-merge networking fixes after downstream PR.

Conflicts:

tools/testing/selftests/net/fcnal-test.sh
  d7a2fc1437f7 ("selftests: net: fcnal-test: check if FIPS mode is enabled")
  dd017c72dde6 ("selftests: fcnal: Test SO_DONTROUTE on TCP sockets.")
https://lore.kernel.org/all/5007b52c-dd16-dbf6-8d64-b9701bfa498b@tessares.net/
https://lore.kernel.org/all/20230619105427.4a0df9b3@canb.auug.org.au/

No adjacent changes.

Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Currently for each timestamp frame, the SW needs to go and read the
received timestamp over the MDIO bus. But the HW has the capability
to store the received nanoseconds part and the least significant two
bits of the seconds in the reserved field of the PTP header. In this
way we could save few MDIO transactions (actually a little more
transactions because the access to the PTP registers are indirect)
for each received frame.

Instead of reading the rest of seconds part of the timestamp of the
frame using MDIO transactions schedule PTP worker thread to read the
seconds part every 500ms and then for each of the received frames use
this information. Because if for example running with 512 frames per
second, there is no point to read 512 times the second part.

Doing all these changes will give a great CPU usage performance.
Running ptp4l with logSyncInterval of -9 will give a ~60% CPU
improvement.

Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The text has been cut/paste from genphy_c45_ethtool_get_eee but not
changed to reflect it performs set.

Additionally, extend the comment. This function implements the logic
that eee_enabled has global control over EEE. When eee_enabled is
false, no link modes will be advertised, and as a result, the MAC
should not transmit LPI.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230619220332.4038924-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>