linux.git/drivers/net/phy, branch v5.0-rc8

net: phy: realtek: Dummy IRQ calls for RTL8366RB

2019-02-24T02:45:28+00:00

This fixes a regression introduced by
commit 0d2e778e38e0ddffab4bb2b0e9ed2ad5165c4bf7
"net: phy: replace PHY_HAS_INTERRUPT with a check for
config_intr and ack_interrupt".

This assumes that a PHY cannot trigger interrupt unless
it has .config_intr() or .ack_interrupt() implemented.
A later patch makes the code assume both need to be
implemented for interrupts to be present.

But this PHY (which is inside a DSA) will happily
fire interrupts without either callback.

Implement dummy callbacks for .config_intr() and
.ack_interrupt() in the phy header to fix this.

Tested on the RTL8366RB on D-Link DIR-685.

Fixes: 0d2e778e38e0 ("net: phy: replace PHY_HAS_INTERRUPT with a check for config_intr and ack_interrupt")
Cc: Heiner Kallweit 
Signed-off-by: Linus Walleij 
Reviewed-by: Andrew Lunn 
Signed-off-by: David S. Miller

net: phy: marvell10g: Fix Multi-G advertisement to only advertise 10G

2019-02-23T21:27:51+00:00

Some Marvell Alaska PHYs support 2.5G, 5G and 10G BaseT links. Their
default behaviour is to advertise all of these modes, but at the moment,
only 10GBaseT is supported. To prevent link partners from establishing
link at that speed, clear these modes upon configuring aneg parameters.

Fixes: 20b2af32ff3f ("net: phy: add Marvell Alaska X 88X3310 10Gigabit PHY support")
Signed-off-by: Maxime Chevallier 
Reported-by: Russell King 
Signed-off-by: David S. Miller

mdio_bus: Fix use-after-free on device_register fails

2019-02-22T23:34:07+00:00

KASAN has found use-after-free in fixed_mdio_bus_init,
commit 0c692d07842a ("drivers/net/phy/mdio_bus.c: call
put_device on device_register() failure") call put_device()
while device_register() fails,give up the last reference
to the device and allow mdiobus_release to be executed
,kfreeing the bus. However in most drives, mdiobus_free
be called to free the bus while mdiobus_register fails.
use-after-free occurs when access bus again, this patch
revert it to let mdiobus_free free the bus.

KASAN report details as below:

BUG: KASAN: use-after-free in mdiobus_free+0x85/0x90 drivers/net/phy/mdio_bus.c:482
Read of size 4 at addr ffff8881dc824d78 by task syz-executor.0/3524

CPU: 1 PID: 3524 Comm: syz-executor.0 Not tainted 5.0.0-rc7+ #45
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
Call Trace:
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0xfa/0x1ce lib/dump_stack.c:113
 print_address_description+0x65/0x270 mm/kasan/report.c:187
 kasan_report+0x149/0x18d mm/kasan/report.c:317
 mdiobus_free+0x85/0x90 drivers/net/phy/mdio_bus.c:482
 fixed_mdio_bus_init+0x283/0x1000 [fixed_phy]
 ? 0xffffffffc0e40000
 ? 0xffffffffc0e40000
 ? 0xffffffffc0e40000
 do_one_initcall+0xfa/0x5ca init/main.c:887
 do_init_module+0x204/0x5f6 kernel/module.c:3460
 load_module+0x66b2/0x8570 kernel/module.c:3808
 __do_sys_finit_module+0x238/0x2a0 kernel/module.c:3902
 do_syscall_64+0x147/0x600 arch/x86/entry/common.c:290
 entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x462e99
Code: f7 d8 64 89 02 b8 ff ff ff ff c3 66 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 bc ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007f6215c19c58 EFLAGS: 00000246 ORIG_RAX: 0000000000000139
RAX: ffffffffffffffda RBX: 000000000073bf00 RCX: 0000000000462e99
RDX: 0000000000000000 RSI: 0000000020000080 RDI: 0000000000000003
RBP: 00007f6215c19c70 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007f6215c1a6bc
R13: 00000000004bcefb R14: 00000000006f7030 R15: 0000000000000004

Allocated by task 3524:
 set_track mm/kasan/common.c:85 [inline]
 __kasan_kmalloc.constprop.3+0xa0/0xd0 mm/kasan/common.c:496
 kmalloc include/linux/slab.h:545 [inline]
 kzalloc include/linux/slab.h:740 [inline]
 mdiobus_alloc_size+0x54/0x1b0 drivers/net/phy/mdio_bus.c:143
 fixed_mdio_bus_init+0x163/0x1000 [fixed_phy]
 do_one_initcall+0xfa/0x5ca init/main.c:887
 do_init_module+0x204/0x5f6 kernel/module.c:3460
 load_module+0x66b2/0x8570 kernel/module.c:3808
 __do_sys_finit_module+0x238/0x2a0 kernel/module.c:3902
 do_syscall_64+0x147/0x600 arch/x86/entry/common.c:290
 entry_SYSCALL_64_after_hwframe+0x49/0xbe

Freed by task 3524:
 set_track mm/kasan/common.c:85 [inline]
 __kasan_slab_free+0x130/0x180 mm/kasan/common.c:458
 slab_free_hook mm/slub.c:1409 [inline]
 slab_free_freelist_hook mm/slub.c:1436 [inline]
 slab_free mm/slub.c:2986 [inline]
 kfree+0xe1/0x270 mm/slub.c:3938
 device_release+0x78/0x200 drivers/base/core.c:919
 kobject_cleanup lib/kobject.c:662 [inline]
 kobject_release lib/kobject.c:691 [inline]
 kref_put include/linux/kref.h:67 [inline]
 kobject_put+0x146/0x240 lib/kobject.c:708
 put_device+0x1c/0x30 drivers/base/core.c:2060
 __mdiobus_register+0x483/0x560 drivers/net/phy/mdio_bus.c:382
 fixed_mdio_bus_init+0x26b/0x1000 [fixed_phy]
 do_one_initcall+0xfa/0x5ca init/main.c:887
 do_init_module+0x204/0x5f6 kernel/module.c:3460
 load_module+0x66b2/0x8570 kernel/module.c:3808
 __do_sys_finit_module+0x238/0x2a0 kernel/module.c:3902
 do_syscall_64+0x147/0x600 arch/x86/entry/common.c:290
 entry_SYSCALL_64_after_hwframe+0x49/0xbe

The buggy address belongs to the object at ffff8881dc824c80
 which belongs to the cache kmalloc-2k of size 2048
The buggy address is located 248 bytes inside of
 2048-byte region [ffff8881dc824c80, ffff8881dc825480)
The buggy address belongs to the page:
page:ffffea0007720800 count:1 mapcount:0 mapping:ffff8881f6c02800 index:0x0 compound_mapcount: 0
flags: 0x2fffc0000010200(slab|head)
raw: 02fffc0000010200 0000000000000000 0000000500000001 ffff8881f6c02800
raw: 0000000000000000 00000000800f000f 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected

Memory state around the buggy address:
 ffff8881dc824c00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
 ffff8881dc824c80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff8881dc824d00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
                                                                ^
 ffff8881dc824d80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
 ffff8881dc824e00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb

Fixes: 0c692d07842a ("drivers/net/phy/mdio_bus.c: call put_device on device_register() failure")
Signed-off-by: YueHaibing 
Reviewed-by: Andrew Lunn 
Signed-off-by: David S. Miller

net: phy: xgmiitorgmii: Support generic PHY status read

2019-02-16T04:20:10+00:00

Some PHY drivers like the generic one do not provide a read_status
callback on their own but rely on genphy_read_status being called
directly.

With the current code, this results in a NULL function pointer call.
Call genphy_read_status instead when there is no specific callback.

Signed-off-by: Paul Kocialkowski 
Signed-off-by: David S. Miller

net: phy: fix potential race in the phylib state machine

2019-02-14T17:04:55+00:00

Russell reported the following race in the phylib state machine
(quoting from his mail):

if (phy_polling_mode(phydev) && phy_is_started(phydev))
	phy_queue_state_machine(phydev, PHY_STATE_TIME);

state = PHY_UP
thread 0			thread 1
				phy_disconnect()
				+-phy_is_started()
phy_is_started()                |
				`-phy_stop()
				  +-phydev->state = PHY_HALTED
				  `-phy_stop_machine()
				    `-cancel_delayed_work_sync()
phy_queue_state_machine()
`-mod_delayed_work()

At this point, the phydev->state_queue() has been added back onto the
system workqueue despite phy_stop_machine() having been called and
cancel_delayed_work_sync() called on it.

Fix this by protecting the complete operation in thread 0.

Fixes: 2b3e88ea6528 ("net: phy: improve phy state checking")
Reported-by: Russell King - ARM Linux admin 
Signed-off-by: Heiner Kallweit 
Reviewed-by: Florian Fainelli 
Signed-off-by: David S. Miller

net: phy: don't use locking in phy_is_started

2019-02-14T17:04:55+00:00

Russell suggested to remove the locking from phy_is_started() because
the read is atomic anyway and actually the locking may be more
misleading.

Fixes: 2b3e88ea6528 ("net: phy: improve phy state checking")
Suggested-by: Russell King - ARM Linux admin 
Signed-off-by: Heiner Kallweit 
Reviewed-by: Florian Fainelli 
Signed-off-by: David S. Miller

net: phy: fix interrupt handling in non-started states

2019-02-14T04:44:12+00:00

phylib enables interrupts before phy_start() has been called, and if
we receive an interrupt in a non-started state, the interrupt handler
returns IRQ_NONE. This causes problems with at least one Marvell chip
as reported by Andrew.
Fix this by handling interrupts the same as in phy_mac_interrupt(),
basically always running the phylib state machine. It knows when it
has to do something and when not.
This change allows to handle interrupts gracefully even if they
occur in a non-started state.

Fixes: 2b3e88ea6528 ("net: phy: improve phy state checking")
Reported-by: Andrew Lunn 
Signed-off-by: Heiner Kallweit 
Reviewed-by: Andrew Lunn 
Reviewed-by: Florian Fainelli 
Signed-off-by: David S. Miller

net: phylink: avoid resolving link state too early

2019-02-12T17:25:18+00:00

During testing on Armada 388 platforms, it was found with a certain
module configuration that it was possible to trigger a kernel oops
during the module load process, caused by the phylink resolver being
triggered for a currently disabled interface.

This problem was introduced by changing the way the SFP registration
works, which now can result in the sfp link down notification being
called during phylink_create().

Fixes: b5bfc21af5cb ("net: sfp: do not probe SFP module before we're attached")
Signed-off-by: Russell King 
Signed-off-by: David S. Miller

net: sfp: do not probe SFP module before we're attached

2019-02-08T23:11:25+00:00

When we probe a SFP module, we expect to be able to call the upstream
device's module_insert() function so that the upstream link can be
configured.  However, when the upstream device is delayed, we currently
may end up probing the module before the upstream device is available,
and lose the module_insert() call.

Avoid this by holding off probing the module until the SFP bus is
properly connected to both the SFP socket driver and the upstream
driver.

Signed-off-by: Russell King 
Signed-off-by: David S. Miller

net: dp83640: expire old TX-skb

2019-02-04T16:54:52+00:00

During sendmsg() a cloned skb is saved via dp83640_txtstamp() in
->tx_queue. After the NIC sends this packet, the PHY will reply with a
timestamp for that TX packet. If the cable is pulled at the right time I
don't see that packet. It might gets flushed as part of queue shutdown
on NIC's side.
Once the link is up again then after the next sendmsg() we enqueue
another skb in dp83640_txtstamp() and have two on the list. Then the PHY
will send a reply and decode_txts() attaches it to the first skb on the
list.
No crash occurs since refcounting works but we are one packet behind.
linuxptp/ptp4l usually closes the socket and opens a new one (in such a
timeout case) so those "stale" replies never get there. However it does
not resume normal operation anymore.

Purge old skbs in decode_txts().

Fixes: cb646e2b02b2 ("ptp: Added a clock driver for the National Semiconductor PHYTER.")
Signed-off-by: Sebastian Andrzej Siewior 
Reviewed-by: Kurt Kanzenbach 
Acked-by: Richard Cochran 
Signed-off-by: David S. Miller