linux.git/drivers/net/phy/phy_device.c, branch v5.3-rc2

net: phy: make exported variables non-static

2019-07-12T22:26:29+00:00

The variables phy_basic_ports_array, phy_fibre_port_array and
phy_all_ports_features_array are declared static and marked
EXPORT_SYMBOL_GPL(), which is at best an odd combination.
Because the variables were decided to be a part of API, this commit
removes the static attributes and adds the declarations to the header.

Fixes: 3c1bcc8614db ("net: ethernet: Convert phydev advertize and supported from u32 to link mode")
Signed-off-by: Denis Efremov 
Signed-off-by: David S. Miller

net: phy: Add more 1000BaseX support detection

2019-06-15T01:46:45+00:00

Commit "net: phy: Add detection of 1000BaseX link mode support" added
support for not filtering out 1000BaseX mode from the PHY's supported
modes in genphy_config_init, but we have to make a similar change in
genphy_read_abilities in order to actually detect it as a supported mode
in the first place. Add this in.

Signed-off-by: Robert Hancock 
Reviewed-by: Florian Fainelli 
Signed-off-by: David S. Miller

net: phy: Add detection of 1000BaseX link mode support

2019-06-06T20:48:51+00:00

Add 1000BaseX to the link modes which are detected based on the
MII_ESTATUS register as per 802.3 Clause 22. This allows PHYs which
support 1000BaseX to work properly with drivers using phylink.

Previously 1000BaseX support was not detected, and if that was the only
mode the PHY indicated support for, phylink would refuse to attach it
due to the list of supported modes being empty.

Signed-off-by: Robert Hancock 
Signed-off-by: David S. Miller

net: phy: enable interrupts when PHY is attached already

2019-05-30T22:02:33+00:00

This patch is a step towards allowing PHY drivers to handle more
interrupt sources than just link change. E.g. several PHY's have
built-in temperature monitoring and can raise an interrupt if a
temperature threshold is exceeded. We may be interested in such
interrupts also if the phylib state machine isn't started.
Therefore move enabling interrupts to phy_request_interrupt().

v2:
- patch added to series

Signed-off-by: Heiner Kallweit 
Reviewed-by: Andrew Lunn 
Signed-off-by: David S. Miller

net: phy: Add phy_standalone sysfs entry

2019-05-30T04:48:53+00:00

Export a phy_standalone device attribute that is meant to give the
indication that this PHY lacks an attached_dev and its corresponding
sysfs link. The attribute will be created only when the
phy_attach_direct() function will be called with a NULL net_device.

Signed-off-by: Ioana Ciornei 
Reviewed-by: Florian Fainelli 
Signed-off-by: David S. Miller

net: phy: Check against net_device being NULL

2019-05-30T04:48:53+00:00

In general, we don't want MAC drivers calling phy_attach_direct with the
net_device being NULL. Add checks against this in all the functions
calling it: phy_attach() and phy_connect_direct().

Signed-off-by: Ioana Ciornei 
Suggested-by: Andrew Lunn 
Reviewed-by: Andrew Lunn 
Reviewed-by: Florian Fainelli 
Signed-off-by: David S. Miller

net: phy: Guard against the presence of a netdev

2019-05-30T04:48:53+00:00

A prerequisite for PHYLIB to work in the absence of a struct net_device
is to not access pointers to it.

Changes are needed in the following areas:

 - Printing: In some places netdev_err was replaced with phydev_err.

 - Incrementing reference count to the parent MDIO bus driver: If there
   is no net device, then the reference count should definitely be
   incremented since there is no chance that it was an Ethernet driver
   who registered the MDIO bus.

 - Sysfs links are not created in case there is no attached_dev.

 - No netif_carrier_off is done if there is no attached_dev.

Signed-off-by: Ioana Ciornei 
Signed-off-by: Vladimir Oltean 
Reviewed-by: Florian Fainelli 
Signed-off-by: David S. Miller

net: phy: Add phy_sysfs_create_links helper function

2019-05-30T04:48:53+00:00

This is a cosmetic patch that wraps the operation of creating sysfs
links between the netdev->phydev and the phydev->attached_dev.

This is needed to keep the indentation level in check in a follow-up
patch where this function will be guarded against the existence of a
phydev->attached_dev.

Signed-off-by: Vladimir Oltean 
Signed-off-by: Ioana Ciornei 
Reviewed-by: Florian Fainelli 
Signed-off-by: David S. Miller

net: phy: Make phy_basic_t1_features use base100t1.

2019-05-23T00:46:28+00:00

Now that there is a link mode for 100BaseT1, use it in
phy_basic_t1_features so T1 PHY drivers will indicate this mode via
the Ethtool API.

Signed-off-by: Andrew Lunn 
Signed-off-by: David S. Miller

Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net

2019-05-08T00:22:09+00:00

Minor conflict with the DSA legacy code removal.

Signed-off-by: David S. Miller