linux.git/drivers/net/fec.h, branch master

freescale: Move the Freescale drivers

2011-08-12T07:22:12+00:00

Move the Freescale drivers into drivers/net/ethernet/freescale/ and
make the necessary Kconfig and Makefile changes.

CC: Sandeep Gopalpet 
CC: Andy Fleming 
CC: Shlomi Gridish 
CC: Li Yang 
CC: Pantelis Antoniou 
CC: Vitaly Bordug 
CC: Dan Malek 
CC: Sylvain Munaut 
Signed-off-by: Jeff Kirsher

Fix common misspellings

2011-03-31T14:26:23+00:00

Fixes generated by 'codespell' and manually reviewed.

Signed-off-by: Lucas De Marchi

net/fec: add dual fec support for mx28

2011-01-09T23:42:56+00:00

This patch is to add mx28 dual fec support. Here are some key notes
for mx28 fec controller.

 - The mx28 fec controller naming ENET-MAC is a different IP from FEC
   used on other i.mx variants.  But they are basically compatible
   on software interface, so it's possible to share the same driver.
 - ENET-MAC design on mx28 made an improper assumption that it runs
   on a big-endian system. As the result, driver has to swap every
   frame going to and coming from the controller.
 - The external phys can only be configured by fec0, which means fec1
   can not work independently and both phys need to be configured by
   mii_bus attached on fec0.
 - ENET-MAC reset will get mac address registers reset too.
 - ENET-MAC MII/RMII mode and 10M/100M speed are configured
   differently FEC.
 - ETHER_EN bit must be set to get ENET-MAC interrupt work.

Signed-off-by: Shawn Guo 
Signed-off-by: David S. Miller

fec: add support for PHY interface platform data

2010-05-24T07:36:13+00:00

The i.MX25 PDK uses RMII to communicate with its PHY. This patch adds
the ability to configure RMII, based on platform data.

Signed-off-by: Baruch Siach 
Acked-by:  Greg Ungerer 
Signed-off-by: David S. Miller

fec: fix definition of 5272 version of FEC_X_DES_ACTIVE register

2009-07-07T01:56:11+00:00

fec: fix definition of 5272 version of FEC_X_DES_ACTIVE register

The ColdFire 5272 FEC driver has a different register address map
than other users of the FEC driver. And its definition of the
FEC_X_DES_ACTIVE register is incorrect, it should be 0x14.
The fec interface cannot transmit data with the old value.

Signed-off-by: Greg Ungerer 
----
Signed-off-by: David S. Miller

fec: remove extra ";" from definition names

2009-07-07T01:55:07+00:00

Signed-off-by: Greg Ungerer 
Signed-off-by: David S. Miller

fec: do not typedef struct types

2009-04-16T09:34:48+00:00

Signed-off-by: Sascha Hauer 
Signed-off-by: David S. Miller

fec: switch to writel/readl

2009-04-16T09:34:47+00:00

Signed-off-by: Sascha Hauer 
Signed-off-by: David S. Miller

fec: Add support for Freescale MX27

2009-02-01T08:58:26+00:00

Signed-off-by: Sascha Hauer 
Acked-by: Greg Ungerer 
Signed-off-by: David S. Miller

m68knommu: fix ColdFire 5272 fec driver hash registers

2008-05-01T15:08:36+00:00

Renamed the 5272 hash_table registers to match the "grp" hash_table
registers of the other ColdFire parts. They are actually a group hash.
The makes for consistent setup across all ColdFire parts.

Signed-off-by: Greg Ungerer 
Signed-off-by: Linus Torvalds