These files were using moduleparam infrastructure, but were not
including anything for it -- which is fine when module.h is being
implicitly included in all files, but that is going away.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>

* 'next-rebase' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci:
  PCI: Clean-up MPS debug output
  pci: Clamp pcie_set_readrq() when using "performance" settings
  PCI: enable MPS "performance" setting to properly handle bridge MPS
  PCI: Workaround for Intel MPS errata
  PCI: Add support for PASID capability
  PCI: Add implementation for PRI capability
  PCI: Export ATS functions to modules
  PCI: Move ATS implementation into own file
  PCI / PM: Remove unnecessary error variable from acpi_dev_run_wake()
  PCI hotplug: acpiphp: Prevent deadlock on PCI-to-PCI bridge remove
  PCI / PM: Extend PME polling to all PCI devices
  PCI quirk: mmc: Always check for lower base frequency quirk for Ricoh 1180:e823
  PCI: Make pci_setup_bridge() non-static for use by arch code
  x86: constify PCI raw ops structures
  PCI: Add quirk for known incorrect MPSS
  PCI: Add Solarflare vendor ID and SFC4000 device IDs

To ease skb->truesize sanitization, its better to be able to localize
all references to skb frags size.

Define accessors : skb_frag_size() to fetch frag size, and
skb_frag_size_{set|add|sub}() to manipulate it.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Per comments from Ben Hutchings on a previous patch, sweep the floors
a little removing unnecessary assignments of zero to fields of struct
ethtool_ringparam in driver code supporting ethtool -g.

Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When I converted some drivers from pci_map_page to skb_frag_dma_map I
neglected to convert PCI_DMA_xDEVICE into DMA_x_DEVICE and
pci_dma_mapping_error into dma_mapping_error.

Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Solarflare linux maintainers <linux-net-drivers@solarflare.com>
Cc: Steve Hodgson <shodgson@solarflare.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	MAINTAINERS
	drivers/net/Kconfig
	drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c
	drivers/net/ethernet/broadcom/tg3.c
	drivers/net/wireless/iwlwifi/iwl-pci.c
	drivers/net/wireless/iwlwifi/iwl-trans-tx-pcie.c
	drivers/net/wireless/rt2x00/rt2800usb.c
	drivers/net/wireless/wl12xx/main.c

Correct the description of ethtool_rxnfc::rule_locs; it is an array
of currently used locations, not all possible valid locations.

Add note that drivers must not use ethtool_rxnfc::rule_locs.

The rule_locs argument to ethtool_ops::get_rxnfc is either NULL or a
pointer to an array of u32, so change the parameter type accordingly.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

An earlier developer misunderstood the meaning of the 'irq' fields and
the driver did not support the standard fields.  To avoid invalidating
existing user documentation, we report and accept changes through
either the standard or 'irq' fields.  If both are changed at the same
time, we prefer the standard field.

Also explain why we don't currently use the 'max_frames' fields.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a range check, and move the check that RX and TX are consistent
from efx_ethtool_set_coalesce().

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>