linux.git/drivers/net/ethernet/freescale, branch v4.2

net: fec: use reinit_completion() in mdio accessor functions

2015-08-25T23:33:16+00:00

Rather than re-initialising the entire completion on every mdio access,
use reinit_completion() which only resets the completion count.  This
avoids possible reinitialisation of the contained spinlock and waitqueue
while they may be in use (eg, mid-completion.)

Such an event could occur if there's a long delay in interrupt handling
causing the mdio accessor to time out, then a second access comes in
while the interrupt handler on a different CPU has called complete().
Another scenario where this has been observed is while locking has
been missing at the phy layer, allowing concurrent attempts to access
the MDIO bus.

Signed-off-by: Russell King 
Signed-off-by: David S. Miller

gianfar: Restore link state settings after MAC reset

2015-08-14T04:26:23+00:00

There are some MAC registers that need to be kept in sync
with the link state parameters, see adjust_link().
However, after a MAC soft reset default values for
these registers are assumed.  In some cases (excepting
if down/ if up for example) adjust_link() does not see
that these values were reset to default because the
priv->old* link parameters were left unchanged.
So, reset the priv->old* link params as well during a
MAC reset to let adjust_link() restore the MAC link
settings to the actual link state values.

Fixes following case, for example:
Setting link to 100M, changing MTU (implies MAC reset),
link state remains unchanged to 100M but MAC registers
were reset to default (1G) breaking the connectivity w/
the PHY.  Closing and re-opening the interface would
restore the MAC link parameters to the correct values.

Signed-off-by: Claudiu Manoil 
Signed-off-by: David S. Miller

gianfar: remove faulty filer optimizer

2015-08-12T21:47:06+00:00

Current filer rule optimization is broken in several ways:
 (1) Can perform reads/writes beyond end of allocated tables.
     (gianfar_ethtool.c:1326).

(2) It breaks badly for rules with more than 2 specifiers
     (e.g. matching ip, port, tos).

Example:
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.1 dst-port 1 tos 1 action 1
Added rule with ID 254
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.2 dst-port 2 tos 2 action 9
Added rule with ID 253
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.3 dst-port 3 tos 3 action 17
Added rule with ID 252
# ./filer_decode /sys/kernel/debug/gfar1/filer_raw
00: MASK == 00000210 AND         Q:00           ctrl:00000080 prop:00000210
01: FPR  == 00000210 AND CLE     Q:00           ctrl:00000281 prop:00000210
02: MASK == ffffffff AND         Q:00           ctrl:00000080 prop:ffffffff
03: DPT  == 00000003 AND         Q:00           ctrl:0000008e prop:00000003
04: TOS  == 00000003 AND         Q:00           ctrl:0000008a prop:00000003
05: DIA  == 0a000003 AND         Q:11           ctrl:0000448c prop:0a000003
06: DPT  == 00000002 AND         Q:00           ctrl:0000008e prop:00000002
07: TOS  == 00000002 AND         Q:00           ctrl:0000008a prop:00000002
08: DIA  == 0a000002 AND         Q:09           ctrl:0000248c prop:0a000002
09: DIA  == 0a000001 AND         Q:00           ctrl:0000008c prop:0a000001
0a: DPT  == 00000001 AND         Q:00           ctrl:0000008e prop:00000001
0b: TOS  == 00000001     CLE     Q:01           ctrl:0000060a prop:00000001
ff: MASK >= 00000000             Q:00           ctrl:00000020 prop:00000000

(Entire cluster gets AND-ed together).

 (3) We observed that the masking rules it generates do not
     play well with clustering on P2020.  Only first rule
     of the cluster would ever fire.  Given that optimizer
     relies heavily on masking this is very hard to fix.

Example:
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.1 dst-port 1  action 1
Added rule with ID 254
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.2 dst-port 2  action 9
Added rule with ID 253
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.3 dst-port 3  action 17
Added rule with ID 252
# ./filer_decode /sys/kernel/debug/gfar1/filer_raw
00: MASK == 00000210 AND         Q:00           ctrl:00000080 prop:00000210
01: FPR  == 00000210 AND CLE     Q:00           ctrl:00000281 prop:00000210
02: MASK == ffffffff AND         Q:00           ctrl:00000080 prop:ffffffff
03: DPT  == 00000003 AND         Q:00           ctrl:0000008e prop:00000003
04: DIA  == 0a000003             Q:11           ctrl:0000440c prop:0a000003
05: DPT  == 00000002 AND         Q:00           ctrl:0000008e prop:00000002
06: DIA  == 0a000002             Q:09           ctrl:0000240c prop:0a000002
07: DIA  == 0a000001 AND         Q:00           ctrl:0000008c prop:0a000001
08: DPT  == 00000001     CLE     Q:01           ctrl:0000060e prop:00000001
ff: MASK >= 00000000             Q:00           ctrl:00000020 prop:00000000

Which looks correct according to the spec but only the first
(eth id 252)/last added rule for 10.0.0.3 will ever trigger.
As if filer did not treat the AND CLE as cluster start but
also kept AND-ing the rules.  We found no errata covering this.

The fact that nobody noticed (2) or (3) makes me think
that this feature is not very widely used and we should just
remove it.

Reported-by: Aleksander Dutkowski 
Signed-off-by: Jakub Kicinski 
Acked-by: Claudiu Manoil 
Signed-off-by: David S. Miller

gianfar: correct list membership accounting

2015-08-12T21:47:05+00:00

At a cost of one line let's make sure .count is correct
when calling gfar_process_filer_changes().

Signed-off-by: Jakub Kicinski 
Signed-off-by: David S. Miller

gianfar: correct filer table writing

2015-08-12T21:47:05+00:00

MAX_FILER_IDX is the last usable index.  Using less-than
will already guarantee that one entry for catch-all rule
will be left, no need to subtract 1 here.

Signed-off-by: Jakub Kicinski 
Signed-off-by: David S. Miller

net: fs_enet: mask interrupts for TX partial frames.

2015-08-11T19:05:34+00:00

We are not interested in interrupts for partially transmitted frames.
Unlike SCC and FCC, the FEC doesn't handle the I bit in buffer
descriptors, instead it defines two interrupt bits, TXB and TXF.

We have to mask TXB in order to only get interrupts once the
frame is fully transmitted.

Signed-off-by: Christophe Leroy 
Signed-off-by: David S. Miller

net: fs_enet: explicitly remove I flag on TX partial frames

2015-08-11T19:05:34+00:00

We are not interested in interrupts for partially transmitted frames,
we have to clear BD_ENET_TX_INTR explicitly otherwise it may remain
from a previously used descriptor.

Signed-off-by: Christophe Leroy 
Signed-off-by: David S. Miller

net: fec: fix initial runtime PM refcount

2015-08-07T01:53:25+00:00

The clocks are initially active and thus the device is marked active.
This still keeps the PM refcount at 0, the pm_runtime_put_autosuspend()
call at the end of probe then leaves us with an invalid refcount of -1,
which in turn leads to the device staying in suspended state even though
netdev open had been called.

Fix this by initializing the refcount to be coherent with the initial
device status.

Fixes:
8fff755e9f8 (net: fec: Ensure clocks are enabled while using mdio bus)

Signed-off-by: Lucas Stach 
Tested-by: Uwe Kleine-König 
Signed-off-by: David S. Miller

gianfar: Enable device wakeup when appropriate

2015-07-31T22:41:49+00:00

The wol_en flag is 0 by default anyway, and we have the
following inconsistency: a MAGIC packet wol capable eth
interface is registered as a wake-up source but unable
to wake-up the system as wol_en is 0 (wake-on flag set to 'd').
Calling set_wakeup_enable() at netdev open is just redundant
because wol_en is 0 by default.
Let only ethtool call set_wakeup_enable() for now.

The bflock is obviously obsoleted, its utility has been corroded
over time.  The bitfield flags used today in gianfar are accessed
only on the init/ config path, with no real possibility of
concurrency - nothing that would justify smth. like bflock.

Signed-off-by: Claudiu Manoil 
Signed-off-by: David S. Miller

gianfar: Fix suspend/resume for wol magic packet

2015-07-31T22:41:49+00:00

If we disable NAPI in the first place we can mask the device's
interrupts (and halt it) without fearing that imask may be
concurrently accessed from interrupt context, so there's
no need to do local_irq_save() around gfar_halt_nodisable().
lock_rx_qs()/unlock_tx_qs() are just obsoleted and potentially
buggy routines.  The txlock is currently used in the driver only
to manage TX congestion, it has nothing to do with halting the
device.  With these changes, the TX processing is stopped before
gfar_halt().

Compact gfar_halt() is used instead of gfar_halt_nodisable(),
as it disables Rx/TX DMA h/w blocks and the Rx/TX h/w queues.
gfar_start() re-enables all these blocks on resume.  Enabling
the magic-packet mode remains the same, note that the RX block
is re-enabled just before entering sleep mode.

Add IRQF_NO_SUSPEND flag for the error interrupt line, to signal
that the interrupt line must remain active during sleep in order
to wake the system by magic packet (MAG) reception interrupt.
(On some systems the MAG interrupt did trigger w/o this flag
as well, but on others it didn't.)

Without these fixes, when suspended during fair Tx traffic the
interface occasionally failed to be woken up by magic packet.

Signed-off-by: Claudiu Manoil 
Signed-off-by: David S. Miller