All drivers that select MII also need to select NET_CORE because MII
depends on it.  This is a bit ridiculous because NET_CORE is just a
menu option that doesn't enable any code by itself.

There is also no need for it to be a visible option, since its users
all select it.

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/wireless/ath/ath9k/Kconfig
	drivers/net/xen-netback/netback.c
	net/batman-adv/bat_iv_ogm.c
	net/wireless/nl80211.c

The ath9k Kconfig conflict was a change of a Kconfig option name right
next to the deletion of another option.

The xen-netback conflict was overlapping changes involving the
handling of the notify list in xen_netbk_rx_action().

Batman conflict resolution provided by Antonio Quartulli, basically
keep everything in both conflict hunks.

The nl80211 conflict is a little more involved.  In 'net' we added a
dynamic memory allocation to nl80211_dump_wiphy() to fix a race that
Linus reported.  Meanwhile in 'net-next' the handlers were converted
to use pre and post doit handlers which use a flag to determine
whether to hold the RTNL mutex around the operation.

However, the dump handlers to not use this logic.  Instead they have
to explicitly do the locking.  There were apparent bugs in the
conversion of nl80211_dump_wiphy() in that we were not dropping the
RTNL mutex in all the return paths, and it seems we very much should
be doing so.  So I fixed that whilst handling the overlapping changes.

To simplify the initial returns, I take the RTNL mutex after we try
to allocate 'tb'.

Signed-off-by: David S. Miller <davem@davemloft.net>

Tulip throws an error when dma debugging is enabled, as it doesn't properly
check dma mapping results with dma_mapping_error() durring tx ring refills.

Easy fix, just add it in, and drop the frame if the mapping is bad

Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Grant Grundler <grundler@parisc-linux.org>
CC: "David S. Miller" <davem@davemloft.net>
Reviewed-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

pci_enable_device() will set device power state to D0,
so it's no need to do it again in tulip_init_one().

Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Removing some boilerplate by using module_pci_driver instead of calling
register and unregister in the otherwise empty init/exit functions.

Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Reviewed-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull in the 'net' tree to get Daniel Borkmann's flow dissector
infrastructure change.

Signed-off-by: David S. Miller <davem@davemloft.net>

The automated ARM build tests have shown that the tulip de4x5 driver
uses the old-style virt_to_bus() interface on some architectures.

Alpha, Sparc and PowerPC did not hit this problem, because they
use a different code path, and most other architectures actually
do provide VIRT_TO_BUS.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

I believe these error messages are already logged
on allocation failure by warn_alloc_failed and so
get a dump_stack on OOM.

Remove the unnecessary additional error logging.

Around these deletions:

o Alignment neatening.
o Remove unnecessary casts of dma_alloc_coherent.
o Hoist assigns from ifs.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull driver core patches from Greg Kroah-Hartman:
 "Here is the big driver core merge for 3.9-rc1

  There are two major series here, both of which touch lots of drivers
  all over the kernel, and will cause you some merge conflicts:

   - add a new function called devm_ioremap_resource() to properly be
     able to check return values.

   - remove CONFIG_EXPERIMENTAL

  Other than those patches, there's not much here, some minor fixes and
  updates"

Fix up trivial conflicts

* tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (221 commits)
  base: memory: fix soft/hard_offline_page permissions
  drivercore: Fix ordering between deferred_probe and exiting initcalls
  backlight: fix class_find_device() arguments
  TTY: mark tty_get_device call with the proper const values
  driver-core: constify data for class_find_device()
  firmware: Ignore abort check when no user-helper is used
  firmware: Reduce ifdef CONFIG_FW_LOADER_USER_HELPER
  firmware: Make user-mode helper optional
  firmware: Refactoring for splitting user-mode helper code
  Driver core: treat unregistered bus_types as having no devices
  watchdog: Convert to devm_ioremap_resource()
  thermal: Convert to devm_ioremap_resource()
  spi: Convert to devm_ioremap_resource()
  power: Convert to devm_ioremap_resource()
  mtd: Convert to devm_ioremap_resource()
  mmc: Convert to devm_ioremap_resource()
  mfd: Convert to devm_ioremap_resource()
  media: Convert to devm_ioremap_resource()
  iommu: Convert to devm_ioremap_resource()
  drm: Convert to devm_ioremap_resource()
  ...

This is another one that makes sense to target for obsolescence, since
it (a)appeared pre-1995, and (b)was rather rare, and (c)did not
really have any statistically significant active linux user base.

Removing this ISA 10Mbit driver support is unlikely to be even noticed
by the user base of 3.9+ linux kernels, especially when the documentation
clearly indicates the vintage with this text:

	 "...designed to  work with all kernels > 1.1.33"

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>