priv->mdio->irq used to be allocated and required freeing, but it
is now a fixed sized array and should no longer be free'd.

Issue detected using static analysis with CoverityScan

Fixes: e7f4dc3536a400 ("mdio: Move allocation of interrupts into core")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Not all devices attached to an MDIO bus are phys. So add an
mdio_device structure to represent the generic parts of an mdio
device, and place this structure into the phy_device.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Have mdio_alloc() create the array of interrupt numbers, and
initialize it to POLLING. This is what most MDIO drivers want, so
allowing code to be removed from the drivers.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Call netif_carrier_off() prior to register_netdev(), otherwise
userspace can see incorrect link state.

Signed-off-by: Atsushi Nemoto <nemoto@toshiba-tops.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

tse_poll() calls __napi_complete() with irq enabled.  This leads napi
poll_list corruption and may stop all napi drivers working.
Use napi_complete() instead of __napi_complete().

Signed-off-by: Atsushi Nemoto <nemoto@toshiba-tops.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

altera_tse_private->sgdmadesclen is always assigned assigned the same
value and never changes during runtime.  Remove the struct member and
use a new define for sizeof(struct sgdma_descrip) instead.

Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Altera TSE MAC rx DMA transfer starts with the 2 additional bytes for IP
payload alignment. This patch fixes tse_rx() function loop which reads DMA
rx status and extracts packet length from it. Status signalises a whole DMA
transfer length, which is 2 bytes longer than the packet itself.

Signed-off-by: Vlastimil Setka <setka@vsis.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for fixed-links in configurations without PHY.
(e.g. connection to a switch, SGMII point to point, SFPs)

Check: Documentation/devicetree/bindings/net/fixed-link.txt.
Signed-off-by: Andreas Oetken <ennoerlangen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch resolves false errors from MSGDMA in TX mSGDMA MM to ST
mode, and is a continuation of the patch recently submitted by Andrea
Oetken. The MSGDMA had a logic bug that masked detection of this issue
prior to Quartus 14.1/Build 164. When the MSGDMA logic bug was addressed
in Quartus 14.1/Build 164, the driver problem was exposed.

The problem is corrected by making sure MSGDMA_DESC_CTL_TR_ERR_IRQ is not
set for any of the transmit DMA descriptors, and only used for receive
descriptors.

Fixes: 71cd26e altera tse: Error-Bit on tx-avalon-stream always set.

Signed-off-by: Chee Nouk Phoon <cnphoon@altera.com>
Signed-off-by: Vince Bridgers <vbridger@opensource.altera.com>a
Cc: Andreas Oetken <ennoerlangen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Error-Bit on the avalon streaming interface of the
tx-dma-channel was always set. In SGMII configurations
this leads to error-symbols on the PCS and packet-rejection
on the receiver side (e.g. SGMII/1000Base-X connected switch).

This only applies to the tse-configuration with MSGDMA.

This issue was detected and fixed on a custom board with
a direct connection to a Marvell switch in SGMII-PHY-Mode.
(incl. custom patches for SGMII-PCS).

According to the datasheet if ff_tx_err (avalon-streaming)
is set it is forwarded to gm_tx_err. As a result the PCS
is forwarding the error by sending a "/V/"-caracter.

Signed-off-by: Andreas Oetken <ennoerlangen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>