linux.git/drivers/net/e1000e, branch v2.6.32 Linux kernel source tree e1000e: do not initiate autonegotiation during OEM configuration 2009-11-20T21:53:32+00:00 Bruce Allan bruce.w.allan@intel.com 2009-11-19T14:17:30+00:00 818f33313caab9be2a10458500dbed4a88c1b334 When configuring the OEM bits in the PHY on 82577/82578, do not restart autonegotiation if the firmware is blocking it (e.g. when an IDE-R session is active) because the link must not go down. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> 
When configuring the OEM bits in the PHY on 82577/82578, do not restart
autonegotiation if the firmware is blocking it (e.g. when an IDE-R session
is active) because the link must not go down.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
e1000e: remove unnecessary 82577 workaround causing link issues 2009-11-20T21:53:29+00:00 Bruce Allan bruce.w.allan@intel.com 2009-11-19T12:36:04+00:00 189983d469c6d98e64ddfb9f9ce76725cb082ee5 A workaround for pre-release versions of 82577 is causing link issues on some switches. The workaround is no longer needed on production parts so remove it. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> 
A workaround for pre-release versions of 82577 is causing link issues on
some switches.  The workaround is no longer needed on production parts so
remove it.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
e1000e: flow control thresholds not correct when changing mtu 2009-11-20T21:53:27+00:00 Bruce Allan bruce.w.allan@intel.com 2009-11-19T12:35:45+00:00 610c992884c80566de31d71ec361a5a7b2a0ed5e When changing MTU, save it off prior to resetting otherwise the flow control thresholds may be miscalculated. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> 
When changing MTU, save it off prior to resetting otherwise the flow control
thresholds may be miscalculated.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
e1000e: add Tx timeout factor for 100Mbps 2009-11-20T21:53:26+00:00 Bruce Allan bruce.w.allan@intel.com 2009-11-19T12:35:26+00:00 4c86e0b9455c8fa8122fc2d10935e892838c8568 On some devices (e.g. 82578) not having a Tx timeout factor when linked at 100Mbps can cause false reports of hardware hangs on busy hubs. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> 
On some devices (e.g. 82578) not having a Tx timeout factor when linked at
100Mbps can cause false reports of hardware hangs on busy hubs.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
e1000e: set flow control thresholds properly after enabling/disabling pause 2009-11-20T21:53:24+00:00 Bruce Allan bruce.w.allan@intel.com 2009-11-19T12:35:08+00:00 29afd690636dab36fe437c54b3a9d5e093bdcd9b When flow control (pause) parameters were changed via ethtool (i.e. enabled or disabled), the newly calculated thresholds were not being written to the device for non-fiber media. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> 
When flow control (pause) parameters were changed via ethtool (i.e. enabled
or disabled), the newly calculated thresholds were not being written to the
device for non-fiber media.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
e1000e: read of PHY register may access wrong page on 82578 2009-11-20T21:53:22+00:00 Bruce Allan bruce.w.allan@intel.com 2009-11-19T12:34:40+00:00 842ec8b64ac34e9b245da31b4a5a49c3e744a714 Remove unnecessary workaround that mistakenly does not perform a page select operation for PHY registers 29 and 30 (assuming these are the PHY debug port address and data registers) on 82578 which can cause reads of the Transmit with No Carrier Sense statistics register on page 778 to be read from an incorrect page. Also error out if the page select operation fails. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> 
Remove unnecessary workaround that mistakenly does not perform a page
select operation for PHY registers 29 and 30 (assuming these are the PHY
debug port address and data registers) on 82578 which can cause reads
of the Transmit with No Carrier Sense statistics register on page 778 to be
read from an incorrect page.  Also error out if the page select operation
fails.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
e1000e: partial revert of 3ec2a2b8 plus FC workraround for 82577/8 2009-11-20T21:53:20+00:00 Bruce Allan bruce.w.allan@intel.com 2009-11-19T12:34:20+00:00 38eb394e33d65abb9d05411547d2058db53b4d23 Commit 3ec2a2b80f3eb53851fe4cef9e65b5d33376ef89 broke Tx/Rx when using jumbo frames on certain parts (i.e. only PAUSE frames could be exchanged once the high water mark was reached preventing normal packet traffic). This patch reverts the breakage and sets appropriate high and low water marks of the Rx FIFO for 82577/82578 which require a workaround due to a flow control issue in hardware. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> 
Commit 3ec2a2b80f3eb53851fe4cef9e65b5d33376ef89 broke Tx/Rx when using
jumbo frames on certain parts (i.e. only PAUSE frames could be exchanged
once the high water mark was reached preventing normal packet traffic).
This patch reverts the breakage and sets appropriate high and low water
marks of the Rx FIFO for 82577/82578 which require a workaround due to a
flow control issue in hardware.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
e1000e: rework disable K1 at 1000Mbps for 82577/82578 2009-10-30T05:48:39+00:00 Bruce Allan bruce.w.allan@intel.com 2009-10-29T13:46:05+00:00 1d5846b9216665d0ae743bf351d0b8fa90c40523 This patch reworks a previous workaround (commit 7d3cabbcc) for an issue in hardware where noise on the interconnect between the MAC and PHY could be generated by a lower power mode (K1) at 1000Mbps resulting in bad packets. Disable K1 while at 1000 Mbps but keep it enabled for 10/100Mbps and when the cable is disconnected. The original version of this workaround was found to be incomplete. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> 
This patch reworks a previous workaround (commit 7d3cabbcc) for an issue
in hardware where noise on the interconnect between the MAC and PHY could
be generated by a lower power mode (K1) at 1000Mbps resulting in bad
packets.  Disable K1 while at 1000 Mbps but keep it enabled for 10/100Mbps
and when the cable is disconnected.  The original version of this
workaround was found to be incomplete.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
e1000e: config PHY via software after resets 2009-10-30T05:48:37+00:00 Bruce Allan bruce.w.allan@intel.com 2009-10-29T13:45:45+00:00 f523d2114e93c559dbcf1b49d46b339fc0eda37a On PCH-based (82577/82578) and some ICH8-based parts (82566) there is an issue with the hardware automatically configuring the PHY with contents from the EEPROM after the PHY is reset, so do the configuration by the driver instead. This was already similarly done for some 82566 parts in e1000_phy_hw_reset_ich8lan() but needs to be done after other resets, so move the PHY configuration code to its own function and call after all PHY resets. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> 
On PCH-based (82577/82578) and some ICH8-based parts (82566) there is an
issue with the hardware automatically configuring the PHY with contents
from the EEPROM after the PHY is reset, so do the configuration by the
driver instead.  This was already similarly done for some 82566 parts in
e1000_phy_hw_reset_ich8lan() but needs to be done after other resets,
so move the PHY configuration code to its own function and call after
all PHY resets.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
e1000e: allow for swflag to be held over consecutive PHY accesses 2009-10-26T23:16:25+00:00 Bruce Allan bruce.w.allan@intel.com 2009-10-26T11:24:02+00:00 5ccdcecb72692d46d7a9264e62751241c7eca559 PCH-based parts (82577/82578) and some ICH8-based parts (82566) need to hold the swflag (sw/fw/hw hardware semaphore) over consecutive PHY accesses in order to perform sw-driven PHY configuration during initialization to workaround known hardware issues (see follow-on patch). This patch provides new PHY read/write functions (and function pointers) that will allow accessing the PHY registers assuming the swflag has already been acquired. The actual PHY register access code has moved into helper functions that are called with a flag indicating whether or not the swflag has already been acquired and acquires/releases it if not. The functions called from within the updated PHY access functions had to be updated to assume the swflag was already acquired, and other functions that called those functions were also updated to acquire/release the swflag. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> 
PCH-based parts (82577/82578) and some ICH8-based parts (82566) need to
hold the swflag (sw/fw/hw hardware semaphore) over consecutive PHY accesses
in order to perform sw-driven PHY configuration during initialization to
workaround known hardware issues (see follow-on patch).  This patch
provides new PHY read/write functions (and function pointers) that will
allow accessing the PHY registers assuming the swflag has already been
acquired.  The actual PHY register access code has moved into helper
functions that are called with a flag indicating whether or not the swflag
has already been acquired and acquires/releases it if not.

The functions called from within the updated PHY access functions had to be
updated to assume the swflag was already acquired, and other functions that
called those functions were also updated to acquire/release the swflag.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>