In VLAN-unaware mode, the Egress Tag (EG_TAG) field in Port VLAN
Control register must be set to Consistent to let tagged frames pass
through as is, otherwise their tags will be stripped.

Fixes: 83163f7dca56 ("net: dsa: mediatek: add VLAN support for MT7530")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: René van Dorst <opensource@vdorst.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To rehash a previous explanation given in commit 1c44ce560b4d ("net:
mscc: ocelot: fix vlan_filtering when enslaving to bridge before link is
up"), the switch driver operates the in a mode where a single VLAN can
be transmitted as untagged on a particular egress port. That is the
"native VLAN on trunk port" use case.

The configuration for this native VLAN is driven in 2 ways:
 - Set the egress port rewriter to strip the VLAN tag for the native
   VID (as it is egress-untagged, after all).
 - Configure the ingress port to drop untagged and priority-tagged
   traffic, if there is no native VLAN. The intention of this setting is
   that a trunk port with no native VLAN should not accept untagged
   traffic.

Since both of the above configurations for the native VLAN should only
be done if VLAN awareness is requested, they are actually done from the
ocelot_port_vlan_filtering function, after the basic procedure of
toggling the VLAN awareness flag of the port.

But there's a problem with that simplistic approach: we are trying to
juggle with 2 independent variables from a single function:
 - Native VLAN of the port - its value is held in port->vid.
 - VLAN awareness state of the port - currently there are some issues
   here, more on that later*.
The actual problem can be seen when enslaving the switch ports to a VLAN
filtering bridge:
 0. The driver configures a pvid of zero for each port, when in
    standalone mode. While the bridge configures a default_pvid of 1 for
    each port that gets added as a slave to it.
 1. The bridge calls ocelot_port_vlan_filtering with vlan_aware=true.
    The VLAN-filtering-dependent portion of the native VLAN
    configuration is done, considering that the native VLAN is 0.
 2. The bridge calls ocelot_vlan_add with vid=1, pvid=true,
    untagged=true. The native VLAN changes to 1 (change which gets
    propagated to hardware).
 3. ??? - nobody calls ocelot_port_vlan_filtering again, to reapply the
    VLAN-filtering-dependent portion of the native VLAN configuration,
    for the new native VLAN of 1. One can notice that after toggling "ip
    link set dev br0 type bridge vlan_filtering 0 && ip link set dev br0
    type bridge vlan_filtering 1", the new native VLAN finally makes it
    through and untagged traffic finally starts flowing again. But
    obviously that shouldn't be needed.

So it is clear that 2 independent variables need to both re-trigger the
native VLAN configuration. So we introduce the second variable as
ocelot_port->vlan_aware.

*Actually both the DSA Felix driver and the Ocelot driver already had
each its own variable:
 - Ocelot: ocelot_port_private->vlan_aware
 - Felix: dsa_port->vlan_filtering
but the common Ocelot library needs to work with a single, common,
variable, so there is some refactoring done to move the vlan_aware
property from the private structure into the common ocelot_port
structure.

Fixes: 97bb69e1e36e ("net: mscc: ocelot: break apart ocelot_vlan_port_apply")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The 88e6185 is reporting it has detected a PHY, when a port is
connected to an SFP. As a result, the fixed-phy configuration is not
being applied. That then breaks packet transfer, since the port is
reported as being down.

Add additional conditions to check the interface mode, and if it is
fixed always configure the port on link up/down, independent of the
PPU status.

Fixes: 30c4a5b0aad8 ("net: mv88e6xxx: use resolved link config in mac_link_up()")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Moving mt7623 logic out off mt7530, is required to make hardware setting
consistent after we introduce phylink to mtk driver.

Fixes: ca366d6c889b ("net: dsa: mt7530: Convert to PHYLINK API")
Reviewed-by: Sean Wang <sean.wang@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: René van Dorst <opensource@vdorst.com>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the bcm_sf2 was converted into a proper platform device driver and
used the new dsa_register_switch() interface, we would still be parsing
the legacy DSA node that contained all the port information since the
platform firmware has intentionally maintained backward and forward
compatibility to client programs. Ensure that we do parse the correct
node, which is "ports" per the revised DSA binding.

Fixes: d9338023fb8e ("net: dsa: bcm_sf2: Make it a real platform device driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We were registering our slave MDIO bus with OF and doing so with
assigning the newly created slave_mii_bus of_node to the master MDIO bus
controller node. This is a bad thing to do for a number of reasons:

- we are completely lying about the slave MII bus is arranged and yet we
  still want to control which MDIO devices it probes. It was attempted
  before to play tricks with the bus_mask to perform that:
  https://www.spinics.net/lists/netdev/msg429420.html but the approach
  was rightfully rejected

- the device_node reference counting is messed up and we are effectively
  doing a double probe on the devices we already probed using the
  master, this messes up all resources reference counts (such as clocks)

The proper fix for this as indicated by David in his reply to the
thread above is to use a platform data style registration so as to
control exactly which devices we probe:
https://www.spinics.net/lists/netdev/msg430083.html

By using mdiobus_register(), our slave_mii_bus->phy_mask value is used
as intended, and all the PHY addresses that must be redirected towards
our slave MDIO bus is happening while other addresses get redirected
towards the master MDIO bus.

Fixes: 461cd1b03e32 ("net: dsa: bcm_sf2: Register our slave MDIO bus")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The 2nd gmac of mediatek soc ethernet may not be connected to a PHY
and a phy-handle isn't always available.
Unfortunately, mt7530 dsa driver assumes that the 2nd gmac is always
connected to switch port 5 and setup mt7530 according to phy address
of 2nd gmac node, causing null pointer dereferencing when phy-handle
isn't defined in dts.
This commit fix this setup code by checking return value of
of_parse_phandle before using it.

Fixes: 38f790a80560 ("net: dsa: mt7530: Add support for port 5")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: René van Dorst <opensource@vdorst.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

KSZ protocol tag is needed by the KSZ DSA drivers.

Fixes: 0b9f9dfbfab4 ("dsa: Allow tag drivers to be built as modules")
Tested-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The port to which the ASP is connected on 7278 is not capable of
processing VLAN tags as part of the Ethernet frame, so allow an user to
configure the egress VLAN policy they want to see applied by purposing
the h_ext.data[1] field. Bit 0 is used to indicate that 0=tagged,
1=untagged.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update relevant code paths to support the programming and matching of
VLAN TCI, this is the only member of the ethtool_flow_ext that we can
match, the switch does not permit matching the VLAN Ethernet Type field.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>