The meaning of CONFIG_EMBEDDED has long since been obsoleted; the option
is used to configure any non-standard kernel with a much larger scope than
only small devices.

This patch renames the option to CONFIG_EXPERT in init/Kconfig and fixes
references to the option throughout the kernel.  A new CONFIG_EMBEDDED
option is added that automatically selects CONFIG_EXPERT when enabled and
can be used in the future to isolate options that should only be
considered for embedded systems (RISC architectures, SLOB, etc).

Calling the option "EXPERT" more accurately represents its intention: only
expert users who understand the impact of the configuration changes they
are making should enable it.

Reviewed-by: Ingo Molnar <mingo@elte.hu>
Acked-by: David Woodhouse <david.woodhouse@intel.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Greg KH <gregkh@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Robin Holt <holt@sgi.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This patch fixes the following kconfig error after changing
CONFIGFS_FS -> select SYSFS:

fs/sysfs/Kconfig:1:error: recursive dependency detected!
fs/sysfs/Kconfig:1:	symbol SYSFS is selected by CONFIGFS_FS
fs/configfs/Kconfig:1:	symbol CONFIGFS_FS is selected by NETCONSOLE_DYNAMIC
drivers/net/Kconfig:3390:	symbol NETCONSOLE_DYNAMIC depends on SYSFS

Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: James Bottomley <James.Bottomley@suse.de>

* 'stable/xenbus' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
  xen/xenbus: making backend support modular is too complex
  xen/pci: Make xen-pcifront be dependent on XEN_XENBUS_FRONTEND
  xen/xenbus: fixup checkpatch issues in xenbus_probe*
  xen/netfront: select XEN_XENBUS_FRONTEND
  xen/xenbus: clean up noise in xenbus_probe_frontend.c
  xen/xenbus: clean up noise in xenbus_probe_backend.c
  xen/xenbus: clean up noise in xenbus_probe.c
  xen/xenbus: cleanup debug noise in xenbus_comms.c
  xen/xenbus: clean up error handling
  xen/xenbus: make frontend bus GPL
  xen/xenbus: make sure backend bus is registered earlier
  xenbus/frontend: register bus earlier
  xen: remove xen/evtchn.h
  xen: add backend driver support
  xen: separate out frontend xenbus

Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to add mx28 dual fec support. Here are some key notes
for mx28 fec controller.

 - The mx28 fec controller naming ENET-MAC is a different IP from FEC
   used on other i.mx variants.  But they are basically compatible
   on software interface, so it's possible to share the same driver.
 - ENET-MAC design on mx28 made an improper assumption that it runs
   on a big-endian system. As the result, driver has to swap every
   frame going to and coming from the controller.
 - The external phys can only be configured by fec0, which means fec1
   can not work independently and both phys need to be configured by
   mii_bus attached on fec0.
 - ENET-MAC reset will get mac address registers reset too.
 - ENET-MAC MII/RMII mode and 10M/100M speed are configured
   differently FEC.
 - ETHER_EN bit must be set to get ENET-MAC interrupt work.

Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure the Xen frontend xenbus is enabled.

Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
[corresponds to c40912891c3b in git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen.git]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>

The binary file of the firmware is moved to linux-firmware repository.
The firmwares are rtl_nic/rtl8168d-1.fw and rtl_nic/rtl8168d-2.fw.
The driver goes along if the firmware couldn't be found. However, it
is suggested to be done with the suitable firmware.

Some wrong PHY parameters are directly corrected in the driver.

Simple firmware checking added per Ben Hutchings suggestion.

Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Ben Hutchings <benh@debian.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	net/ipv4/fib_frontend.c

Conflicts:
	drivers/net/wireless/ath/ath9k/ar9003_eeprom.c
	net/llc/af_llc.c

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (27 commits)
  af_unix: limit recursion level
  pch_gbe driver: The wrong of initializer entry
  pch_gbe dreiver: chang author
  ucc_geth: fix ucc halt problem in half duplex mode
  inet: Fix __inet_inherit_port() to correctly increment bsockets and num_owners
  ehea: Add some info messages and fix an issue
  hso: fix disable_net
  NET: wan/x25_asy, move lapb_unregister to x25_asy_close_tty
  cxgb4vf: fix setting unicast/multicast addresses ...
  net, ppp: Report correct error code if unit allocation failed
  DECnet: don't leak uninitialized stack byte
  au1000_eth: fix invalid address accessing the MAC enable register
  dccp: fix error in updating the GAR
  tcp: restrict net.ipv4.tcp_adv_win_scale (#20312)
  netns: Don't leak others' openreq-s in proc
  Net: ceph: Makefile: Remove unnessary code
  vhost/net: fix rcu check usage
  econet: fix CVE-2010-3848
  econet: fix CVE-2010-3850
  econet: disallow NULL remote addr for sendmsg(), fixes CVE-2010-3849
  ...