Pull ubifs updates from Artem Bityutskiy:

 - Improve the NOR erasure quirk - now it tries to do as little writes
   as possible, because the eraseblock may be in an "unstable" state and
   write operation sometimes causes NOR chip lock-ups.

 - Both UBI and UBIFS changes are now maintainer in one single tree,
   because the amount of changes dropped significantly.

* tag 'upstream-3.14-rc1' of git://git.infradead.org/linux-ubifs:
  UBI: avoid program operation on NOR flash after erasure interrupted
  MAINTAINERS: keep UBI and UBIFS stuff in the same tree
  UBI: fix error return code

Pull more powerpc bits from Ben Herrenschmidt:
 "Here are a few more powerpc bits for this merge window.  The bulk is
  made of two pull requests from Scott and Anatolij that I had missed
  previously (they arrived while I was away).  Since both their branches
  are in -next independently, and the content has been around for a
  little while, they can still go in.

  The rest is mostly bug and regression fixes, a small series of
  cleanups to our pseries cpuidle code (including moving it to the right
  place), and one new cpuidle bakend for the powernv platform.  I also
  wired up the new sched_attr syscalls"

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (37 commits)
  powerpc: Wire up sched_setattr and sched_getattr syscalls
  powerpc/hugetlb: Replace __get_cpu_var with get_cpu_var
  powerpc: Make sure "cache" directory is removed when offlining cpu
  powerpc/mm: Fix mmap errno when MAP_FIXED is set and mapping exceeds the allowed address space
  powerpc/powernv/cpuidle: Back-end cpuidle driver for powernv platform.
  powerpc/pseries/cpuidle: smt-snooze-delay cleanup.
  powerpc/pseries/cpuidle: Remove MAX_IDLE_STATE macro.
  powerpc/pseries/cpuidle: Make cpuidle-pseries backend driver a non-module.
  powerpc/pseries/cpuidle: Use cpuidle_register() for initialisation.
  powerpc/pseries/cpuidle: Move processor_idle.c to drivers/cpuidle.
  powerpc: Fix 32-bit frames for signals delivered when transactional
  powerpc/iommu: Fix initialisation of DART iommu table
  powerpc/numa: Fix decimal permissions
  powerpc/mm: Fix compile error of pgtable-ppc64.h
  powerpc: Fix hw breakpoints on !HAVE_HW_BREAKPOINT configurations
  clk: corenet: Adds the clock binding
  powerpc/booke64: Guard e6500 tlb handler with CONFIG_PPC_FSL_BOOK3E
  powerpc/512x: dts: add MPC5125 clock specs
  powerpc/512x: clk: support MPC5121/5123/5125 SoC variants
  powerpc/512x: clk: enforce even SDHC divider values
  ...

<<
Switch mpc512x to the common clock framework and adapt mpc512x
drivers to use the new clock driver. Old PPC_CLOCK code is
removed entirely since there are no users any more.
>>

Pull MTD updates from Brian Norris:
 - Add me (Brian Norris) as an additional MTD maintainer (it'd be nice to get
   David's "ack" for this; I'm sure he approves, but he's been pretty silent
   lately)
 - Add Ezequiel Garcie as maintainer for the pxa3xx NAND driver
 - Last (?) round of pxa3xx improvements for supporting Armada 370/XP
 - Typical churn in driver boilerplate (OOM messages, printk()'s, devm_*, etc.)
 - Quad read mode support for SPI NOR driver (m25p80)
 - Update Davinci NAND driver to prepare for use on new platforms
 - Begin to kill off NAND_MAX_{PAGE,OOB}SIZE macros; more work is pending
 - Miscellaneous NAND device support (new IDs)
 - Add READ RETRY support for Micron MLC NAND
 - Support new GPMI NAND ECC layout device-tree binding
 - Avoid mapping stack/vmalloc() memory for GPMI NAND DMA

* tag 'for-linus-20140127' of git://git.infradead.org/linux-mtd: (151 commits)
  mtd: gpmi: add sanity check when mapping DMA for read_buf/write_buf
  mtd: gpmi: allocate a proper buffer for non ECC read/write
  mtd: m25p80: Set rx_nbits for Quad SPI transfers
  mtd: m25p80: Enable Quad SPI read transfers for s25fl512s
  mtd: s3c2410: Merge plat/regs-nand.h into s3c2410.c
  mtd: mtdram: add missing 'const'
  mtd: m25p80: assign default read command
  mtd: nuc900_nand: remove redundant return value check of platform_get_resource()
  mtd: plat_nand: remove redundant return value check of platform_get_resource()
  mtd: nand: add Intel manufacturer ID
  mtd: nand: add SanDisk manufacturer ID
  mtd: nand: add support for Samsung K9LCG08U0B
  mtd: nand: pxa3xx: Add support for 2048 bytes page size devices
  mtd: m25p80: Use OPCODE_QUAD_READ_4B for 4-byte addressing
  mtd: nand: don't use {read,write}_buf for 8-bit transfers
  mtd: nand: use __packed shorthand
  mtd: nand: support Micron READ RETRY
  mtd: nand: add generic READ RETRY support
  mtd: nand: add ONFI vendor block for Micron
  mtd: nand: localize ECC failures per page
  ...

The buffer pointer passed from the upper layer may points to
a buffer in the stack or a buffer allocated by vmalloc, and etc..

This patch adds more sanity check to this buffer.
After this patch, if we meet a buffer which is allocated by vmalloc or
a buffer in the stack, we will use our own DMA buffer @data_buffer_dma
to do the DMA operations. If the buffer is not the cases above, we will
map it for DMA operations directly.

Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

The @data_buffer_dma buffer is used for non ECC read/write.

Currently, the length of the buffer is PAGE_SIZE, but the NAND chip may
has 8K page or 16K page. So we have to extend it for the large page NAND
chips.

The gpmi_alloc_dma_buffer will be called twice. The first time is to
allocate a temporary buffer for scanning the NAND chip; The second time
is to allocate a buffer to store the real page content.

This patch allocates a buffer of PAGE_SIZE size for scanning the NAND
chip when gpmi_alloc_dma_buffer is called the first time, and allocates a
buffer of the real NAND page size for the second time gpmi_alloc_dma_buffer
is called.

Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

When using the Quad Read opcode, SPI masters still use Single SPI
transfers, as spi_transfer.rx_nbits defaults to SPI_NBITS_SINGLE.
Use SPI_NBITS_QUAD to fix this.

While an earlier version of commit 3487a63955c34ea508bcf4ca5131ddd953876e2d
("drivers: mtd: m25p80: add quad read support") did this correctly, it was
forgotten in the version that got merged.

Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Spansion s25fl512s supports Quad SPI transfers, hence set the
M25P80_QUAD_READ flag.

Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Pull trivial tree updates from Jiri Kosina:
 "Usual rocket science stuff from trivial.git"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
  neighbour.h: fix comment
  sched: Fix warning on make htmldocs caused by wait.h
  slab: struct kmem_cache is protected by slab_mutex
  doc: Fix typo in USB Gadget Documentation
  of/Kconfig: Spelling s/one/once/
  mkregtable: Fix sscanf handling
  lp5523, lp8501: comment improvements
  thermal: rcar: comment spelling
  treewide: fix comments and printk msgs
  IXP4xx: remove '1 &&' from a condition check in ixp4xx_restart()
  Documentation: update /proc/uptime field description
  Documentation: Fix size parameter for snprintf
  arm: fix comment header and macro name
  asm-generic: uaccess: Spelling s/a ny/any/
  mtd: onenand: fix comment header
  doc: driver-model/platform.txt: fix a typo
  drivers: fix typo in DEVTMPFS_MOUNT Kconfig help text
  doc: Fix typo (acces_process_vm -> access_process_vm)
  treewide: Fix typos in printk
  drivers/gpu/drm/qxl/Kconfig: reformat the help text
  ...

plat/regs-nand.h is used only by S3C2410 nand driver. Since there
are no other users, merge this file into the driver code to remove
platform dependency. While at it also remove unused macros.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>