This MIPS driver does not support COMPILE_TEST yet and failed to build
under my radar.

Replace 'mtd' chich is not defined in the scope of xway_nand_remove()
by nand_to_mtd(chip). The mistake has been added in the long series
dropping nand_release().

Tested with a 7.3.0 MIPS GCC toolchain built with Buildroot.

Fixes: 9fdd78f7bcda ("mtd: rawnand: xway: Stop using nand_release()")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200626065511.16424-1-miquel.raynal@bootlin.com

ns_find_operation() returns 0 on success.

Fixes: 052a7a5374bc ("mtd: rawnand: nandsim: Clean error handling")
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200615113404.25447-1-richard@nod.at

Raw NAND core changes:
* Stop using nand_release(), patched all drivers.
* Give more information about the ECC weakness when not matching the
  chip's requirement.
* MAINTAINERS updates.
* Support emulated SLC mode on MLC NANDs.
* Support "constrained" controllers, adapt the core and ONFI/JEDEC
  table parsing and Micron's code.
* Take check_only into account.
* Add an invalid ECC mode to discriminate with valid ones.
* Return an enum from of_get_nand_ecc_algo().
* Drop OOB_FIRST placement scheme.
* Introduce nand_extract_bits().
* Ensure a consistent bitflips numbering.
* BCH lib:
  - Allow easy bit swapping.
  - Rework a little bit the exported function names.
* Fix nand_gpio_waitrdy().
* Propage CS selection to sub operations.
* Add a NAND_NO_BBM_QUIRK flag.
* Give the possibility to verify a read operation is supported.
* Add a helper to check supported operations.
* Avoid indirect access to ->data_buf().
* Rename the use_bufpoi variables.
* Fix comments about the use of bufpoi.
* Rename a NAND chip option.
* Reorder the nand_chip->options flags.
* Translate obscure bitfields into readable macros.
* Timings:
  - Fix default values.
  - Add mode information to the timings structure.

Raw NAND controller driver changes:
* Fixed many error paths.
* Arasan
  - New driver
* Au1550nd:
  - Various cleanups
  - Migration to ->exec_op()
* brcmnand:
  - Misc cleanup.
  - Support v2.1-v2.2 controllers.
  - Remove unused including <linux/version.h>.
  - Correctly verify erased pages.
  - Fix Hamming OOB layout.
* Cadence
  - Make cadence_nand_attach_chip static.
* Cafe:
  - Set the NAND_NO_BBM_QUIRK flag
* cmx270:
  - Remove this controller driver.
* cs553x:
  - Misc cleanup
  - Migration to ->exec_op()
* Davinci:
  - Misc cleanup.
  - Migration to ->exec_op()
* Denali:
  - Add more delays before latching incoming data
* Diskonchip:
   - Misc cleanup
   - Migration to ->exec_op()
* Fsmc:
  - Change to non-atomic bit operations.
* GPMI:
  - Use nand_extract_bits()
  - Fix runtime PM imbalance.
* Ingenic:
  - Migration to exec_op()
  - Fix the RB gpio active-high property on qi, lb60
  - Make qi_lb60_ooblayout_ops static.
* Marvell:
   - Misc cleanup and small fixes
* Nandsim:
  - Fix the error paths, driver wide.
* Omap_elm:
  - Fix runtime PM imbalance.
* STM32_FMC2:
  - Misc cleanups (error cases, comments, timeout valus, cosmetic
    changes).

NAND ECC modes (or providers) have their own enumeration but, unlike
their algorithms counterpart, there is no invalid or uninitialized
value to discriminate between an error and having chosen a no-ECC
situation. Add an "invalid" entry for this purpose.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200526195633.11543-7-miquel.raynal@bootlin.com

There is an enumeration to list ECC algorithm, let's use it instead of
returning an int.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200526195633.11543-6-miquel.raynal@bootlin.com

This scheme has been introduced for the Davinci controller and means
that the OOB area must be read *before* the rest of the data. This has
nothing to do with the ECC in OOB placement as it could be understood
and most importantly, there is no point in having this function out of
the Davinci NAND controller driver. A DT property for this scheme has
been added but never used, even by the Davinci driver which only uses
this scheme to change the default nand_read_page().

Move the main read_page() helper into the Davinci driver and remove
the remaining boilerplate.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200526195633.11543-4-miquel.raynal@bootlin.com

In new code, the use of typedef is discouraged. Turn this one in the
raw NAND core into a regular enumeration.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200526195633.11543-3-miquel.raynal@bootlin.com

This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().

Now that all drivers have been converted to do not use nand_release()
anymore, let's remove this helper.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-63-miquel.raynal@bootlin.com

Reorganize ns_cleanup_module() to fit the reworked exit path of
ns_init_module().

There is no need for a ns_free_lists() function anymore, so drop it.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200525085851.17682-18-miquel.raynal@bootlin.com

Rename the "error" label to gave it a meaning.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200525085851.17682-17-miquel.raynal@bootlin.com