commit 65b97cf6b8de introduced in v3.7 caused a regression
by using a reversed CS_MASK thus causing omap_calculate_ecc to
always fail. As the NAND base driver never checks for .calculate()'s
return value, the zeroed ECC values are used as is without showing
any error to the user. However, this won't work and the NAND device
won't be guarded by any error code.

Fix the issue by using the correct mask.

Code was tested on omap3beagle using the following procedure
- flash the primary bootloader (MLO) from the kernel to the first
NAND partition using nandwrite.
- boot the board from NAND. This utilizes OMAP ROM loader that
relies on 1-bit Hamming code ECC.

Fixes: 65b97cf6b8de (mtd: nand: omap2: handle nand on gpmc)

Cc: <stable@vger.kernel.org>	[3.7+]
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

For v3.12 and prior, 1-bit Hamming code ECC via software was the
default choice. Commit c66d039197e4 in v3.13 changed the behaviour
to use 1-bit Hamming code via Hardware using a different ECC layout
i.e. (ROM code layout) than what is used by software ECC.

This ECC layout change causes NAND filesystems created in v3.12
and prior to be unusable in v3.13 and later. So revert back to
using software ECC by default if an ECC scheme is not explicitely
specified.

This defect can be observed on the following boards during legacy boot

-omap3beagle
-omap3touchbook
-overo
-am3517crane
-devkit8000
-ldp
-3430sdp

Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Pull MTD updates from Brian Norris:
 "AMD-compatible CFI driver:
   - Support OTP programming for Micron M29EW family
   - Increase buffer write timeout, according to detected flash
     parameter info

  NAND
   - Add helpers for retrieving ONFI timing modes
   - GPMI: provide option to disable bad block marker swapping (required
     for Ka-On electronics platforms)

  SPI NOR
   - EON EN25QH128 support
   - Support new Flag Status Register (FSR) on a few Micron flash

  Common
   - New sysfs entries for bad block and ECC stats

  And a few miscellaneous refactorings, cleanups, and driver
  improvements"

* tag 'for-linus-20140808' of git://git.infradead.org/linux-mtd: (31 commits)
  mtd: gpmi: make blockmark swapping optional
  mtd: gpmi: remove line breaks from error messages and improve wording
  mtd: gpmi: remove useless (void *) type casts and spaces between type casts and variables
  mtd: atmel_nand: NFC: support multiple interrupt handling
  mtd: atmel_nand: implement the nfc_device_ready() by checking the R/B bit
  mtd: atmel_nand: add NFC status error check
  mtd: atmel_nand: make ecc parameters same as definition
  mtd: nand: add ONFI timing mode to nand_timings converter
  mtd: nand: define struct nand_timings
  mtd: cfi_cmdset_0002: fix do_write_buffer() timeout error
  mtd: denali: use 8 bytes for READID command
  mtd/ftl: fix the double free of the buffers allocated in build_maps()
  mtd: phram: Fix whitespace issues
  mtd: spi-nor: add support for EON EN25QH128
  mtd: cfi_cmdset_0002: Add support for locking OTP memory
  mtd: cfi_cmdset_0002: Add support for writing OTP memory
  mtd: cfi_cmdset_0002: Invalidate cache after entering/exiting OTP memory
  mtd: cfi_cmdset_0002: Add support for reading OTP
  mtd: spi-nor: add support for flag status register on Micron chips
  mtd: Account for BBT blocks when a partition is being allocated
  ...

Pull MIPS updates from Ralf Baechle:
 "This is the main pull request for 3.17.  It contains:

   - misc Cavium Octeon, BCM47xx, BCM63xx and Alchemy  updates
   - MIPS ptrace updates and cleanups
   - various fixes that will also go to -stable
   - a number of cleanups and small non-critical fixes.
   - NUMA support for the Loongson 3.
   - more support for MSA
   - support for MAAR
   - various FP enhancements and fixes"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (139 commits)
  MIPS: jz4740: remove unnecessary null test before debugfs_remove
  MIPS: Octeon: remove unnecessary null test before debugfs_remove_recursive
  MIPS: ZBOOT: implement stack protector in compressed boot phase
  MIPS: mipsreg: remove duplicate MIPS_CONF4_FTLBSETS_SHIFT
  MIPS: Bonito64: remove a duplicate define
  MIPS: Malta: initialise MAARs
  MIPS: Initialise MAARs
  MIPS: detect presence of MAARs
  MIPS: define MAAR register accessors & bits
  MIPS: mark MSA experimental
  MIPS: Don't build MSA support unless it can be used
  MIPS: consistently clear MSA flags when starting & copying threads
  MIPS: 16 byte align MSA vector context
  MIPS: disable preemption whilst initialising MSA
  MIPS: ensure MSA gets disabled during boot
  MIPS: fix read_msa_* & write_msa_* functions on non-MSA toolchains
  MIPS: fix MSA context for tasks which don't use FP first
  MIPS: init upper 64b of vector registers when MSA is first used
  MIPS: save/disable MSA in lose_fpu
  MIPS: preserve scalar FP CSR when switching vector context
  ...

replace au_read/write/sync with __raw_read/write and wmb.

Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7465/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This patch changes the static memory controller registers to offsets
from base, prefixes them with AU1000_ to avoid silent failures due to
changed addresses and introduces helpers to access them.

No functional changes, comparing assembly of a few select functions shows
no differences.

Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7463/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

With a flash-based BBT there is no reason to move the Factory Bad
Block Marker from the data area buffer (to where it is mapped by the
GPMI NAND controller) to the OOB buffer. Thus, make this feature
configurable via DT. This is required for the Ka-Ro electronics
platforms.

In the original code 'this->swap_block_mark' was synonymous with
'!GPMI_IS_MX23()', so use the latter at the relevant places.

Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Acked-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Fix the following error, which sometimes happens during the NFC data
transfer:

  atmel_nand 80000000.nand: Time out to wait for interrupt: 0x00010000
  atmel_nand 80000000.nand: something wrong, No XFR_DONE interrupt comes.

The root cause is that in the interrupt handler, we read the ISR but
only handle one interrupt. If more than one interrupt arrive at the same
time, then the second one will be lost.

During the NFC data transfer. Two NFC interrupts (NFC_CMD_DONE and
NFC_XFR_DONE) may come at the same time.

NFC_CMD_DONE means NFC command is sent, and NFC_XFR_DONE means NFC data
is transferred.

This patch can handle multiple NFC interrupts at the same time. During
the NFC data transfer, we need to wait for two NFC interrupts:
NFC_CMD_DONE and NFC_XFR_DONE.

Also we separate the completion initialization code to a
nfc_prepare_interrupt(), which is paired with nfc_wait_interrupt().

We call nfc_prepare_interrupt() before sending out nfc commands, to make
sure no interrupt lost.

Reported-by: Matthieu CRAPET <Matthieu.CRAPET@ingenico.com>
Tested-by: Matthieu Crapet <Matthieu.Crapet@ingenico.com>
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>