This drastically reduces the rate at which the MMC_SEND_STATUS cmd polls
for completion of the MMC Erase operation.  The patch does this by adding
a backoff sleep that starts by sleeping for short intervals (128-256us),
and ramps up to sleeping for 32-64ms.

Even on very quickly completing erase operations, the loop iterates a few
times, so not too much extra latency is added to these commands.

For long running discard operarations, like a full-device secure discard,
this change drops the interrupt rates on my single-core NXP I.MX6UL from
45000/s to about 20/s, and greatly improves system responsiveness.

Signed-off-by: Martin Hicks <mort@bork.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The hard-coded 10ms delay in mmc_power_up came from
commit 79bccc5aefb4 ("mmc: increase power up delay"), which said "The TI
controller on Toshiba Tecra M5 needs more time to power up or the cards
will init incorrectly or not at all." But it's too engineering solution
for a special board but force all platforms to wait for that long time,
especially painful for mmc_power_up for eMMC when booting.

However, it's added since 2009, and we can't tell if other platforms
benefit from it. But in practise, the modern hardware are most likely to
have a stable power supply with 1ms after setting it for no matter PMIC
or discrete power. And more importnatly, most regulators implement the
callback of ->set_voltage_time_sel() for regulator core to wait for
specific period of time for the power supply to be stable, which means
once regulator_set_voltage_* return, the power should reach the the
minimum voltage that works for initialization. Of course, if there
are some other ways for host to power the card, we should allow them
to argue a suitable delay as well.

With this patch, we could assign the delay from firmware, or we could
assigne it via ->set_ios() callback from host drivers.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

MMC_CORE_TIMEOUT_MS isn't being used no more, let's drop it.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Move the corresponding code for setting the initial signal voltage, from
mmc_power_up() into a new function, mmc_set_initial_signal_voltage().

Make the function internally available to the mmc core, as to allow the
following changes to make use of it.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>

It's rather common that a firmware is loaded into an SDIO func device
memory, by the corresponding SDIO func driver during ->probe() time.

However, to actually start running the new firmware, sometimes a soft reset
(no power cycle) and a re-initialization of the card is needed. This is for
example the case with the Espressif ESP8089 WiFi chips, when connected to
an SDIO interface.

To cope with this scenario, let's add a new exported function,
mmc_sw_reset(), which may be called when a soft reset and re-initialization
of the card are needed.

The mmc_sw_reset() is implemented on top of a new bus ops callback, similar
to how the mmc_hw_reset() has been implemented.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>

The bus ops ->reset() executes a full HW reset of the card, as the calling
function mmc_hw_reset() also indicates by its name. Let's convert to follow
the similar names, for both the bus ops callback and for the corresponding
bus ops functions, as to clarify the purpose of code.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>

Commit 03dbaa04a2e5 ("mmc: slot-gpio: Add support to enable irq wake on
cd_irq") enabled wakeup at initialization. However drivers may wish to
enable and disable based on different criteria. Add a helper function
mmc_gpio_set_cd_wake() to make it easy for drivers to do that.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

If the max_discard value is zero, the conditional branch that checks the
trim capabilities will never update this value with max_trim.

Change the condition statement to also check the max_discard value in order
to avoid an unnecessary call to mmc_do_calc_max_discard.

Signed-off-by: Sergio Valverde <vlvrdv@gmail.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chip.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The Weibu F3C MiniPC has an onboard AP6255 module, presenting
two SDIO functions on a single MMC host (Bluetooth/btsdio and
WiFi/brcmfmac), and the mmc layer correctly detects this as
non-removable.

After suspend/resume, the wifi and bluetooth interfaces disappear
and do not get probed again.

The conditions here are:

 1. During suspend, we reach mmc_pm_notify()

 2. mmc_pm_notify() calls mmc_sdio_pre_suspend() to see if we can
    suspend the SDIO host. However, mmc_sdio_pre_suspend() returns
    -ENOSYS because btsdio_driver does not have a suspend method.

 3. mmc_pm_notify() proceeds to remove the card

 4. Upon resume, mmc_rescan() does nothing with this host, because of
    the rescan_entered check which aims to only scan a non-removable
    device a single time (i.e. during boot).

Fix the loss of functionality by detecting that we are unable to
suspend a non-removable host, so avoid the forced removal in that
case. The comment above this function already indicates that this
code was only intended for removable devices.

Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Remove code no longer needed after the switch to blk-mq.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>