Currently when the device secure discard implementation is
blacklisted (MMC_QUIRK_SEC_ERASE_TRIM_BROKEN quirk is set)
instead of secure discard we're going to do normal discard,
which is wrong.

When the secure discard is known to be broken we should just
disallow it entirely and not advertise this functionality to
the user. Fix it.

Also move mmc_fixup_device() in from of mmc_blk_alloc() so we
can get quirks set before we attempt to set queue information.

Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Pull MMC updates from Chris Ball:
 "MMC highlights for 3.15:

  Core:
   - CONFIG_MMC_UNSAFE_RESUME=y is now default behavior
   - DT bindings for SDHCI UHS, eMMC HS200, high-speed DDR, at 1.8/1.2V
   - Add GPIO descriptor based slot-gpio card detect API

  Drivers:
   - dw_mmc: Refactor SOCFPGA support as a variant inside dw_mmc-pltfm.c
   - mmci: Support HW busy detection on ux500
   - omap: Support MMC_ERASE
   - omap_hsmmc: Support MMC_PM_KEEP_POWER, MMC_PM_WAKE_SDIO_IRQ, (a)cmd23
   - rtsx: Support pre-req/post-req async
   - sdhci: Add support for Realtek RTS5250 controllers
   - sdhci-acpi: Add support for 80860F16, fix 80860F14/SDIO card detect
   - sdhci-msm: Add new driver for Qualcomm SDHCI chipset support
   - sdhci-pxav3: Add support for Marvell Armada 380 and 385 SoCs"

* tag 'mmc-updates-for-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (102 commits)
  mmc: sdhci-acpi: Intel SDIO has broken card detect
  mmc: sdhci-pxav3: add support for the Armada 38x SDHCI controller
  mmc: sdhci-msm: Add platform_execute_tuning implementation
  mmc: sdhci-msm: Initial support for Qualcomm chipsets
  mmc: sdhci-msm: Qualcomm SDHCI binding documentation
  sdhci: only reprogram retuning timer when flag is set
  mmc: rename ARCH_BCM to ARCH_BCM_MOBILE
  mmc: sdhci: Allow for irq being shared
  mmc: sdhci-acpi: Add device id 80860F16
  mmc: sdhci-acpi: Fix broken card detect for ACPI HID 80860F14
  mmc: slot-gpio: Add GPIO descriptor based CD GPIO API
  mmc: slot-gpio: Split out CD IRQ request into a separate function
  mmc: slot-gpio: Record GPIO descriptors instead of GPIO numbers
  Revert "dts: socfpga: Add support for SD/MMC on the SOCFPGA platform"
  mmc: sdhci-spear: use generic card detection gpio support
  mmc: sdhci-spear: remove support for power gpio
  mmc: sdhci-spear: simplify resource handling
  mmc: sdhci-spear: fix platform_data usage
  mmc: sdhci-spear: fix error handling paths for DT
  mmc: sdhci-bcm-kona: fix build errors when built-in
  ...

When sending a stop command at the recovery path, use a R1B response
when the failing data request are a WRITE. Thus we also care about the
busy detection completion in this case.

For a failing READ request, we use a R1 response for the stop command,
since we don't need to care about busy detection in this case.

To align behavior between hosts supporting MMC_CAP_WAIT_WHILE_BUSY and
those who are not, we add a CMD13 polling method for the card's status.

We also respect whether the host has specified the max_busy_timeout,
which means we may fallback to CMD13 polling if the timeout is greater
than what the host are able to support.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>

Currently for write request we don't trust the hw busy detection to be
fully handled by host, thus we also poll the card's status until we see
it's gets out of the busy state.

Still there are scenarios where it will a benefit to trust the hw busy
detection done by the host, since no additional polling is needed.
Let's prepare card_busy_detect() to be able to handle this.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>

To complete a data write request we poll for the card's status register
by sending CMD13. The are other scenarios when this polling method are
needed, which is why we here moves this code to it's own function. No
functional change.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>

While using open ended transmission and thus ending the transfer by
sending a stop command, we shall use R1B only for writes and R1 shall
be used for reads. Previously R1B were used in both cases.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>

We must use a 64-bit for this, otherwise overflowed bits get lost, and
that can result in a lower than intended value set.

Fixes: 8e0cb8a1f6ac ("ARM: 7797/1: mmc: Use dma_max_pfn(dev) helper for bounce_limit calculations")
Fixes: 7d35496dd982 ("ARM: 7796/1: scsi: Use dma_max_pfn(dev) helper for bounce_limit calculations")
Tested-Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

There is no need for keeping a host cap for MMC_CAP2_SANITIZE, instead
we just make the feature default available.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>

Under function mmc_blk_issue_rq, after an MMC discard operation,
the MMC request data structure may be freed in memory. Later in
the same function, the check of req->cmd_flags & MMC_REQ_SPECIAL_MASK
is dangerous and invalid. It causes the MMC host not to be released
when it should.

This patch fixes the issue by marking the special request down before
the discard/flush operation.

Reported by: Harold (SoonYeal) Yang <haroldsy@broadcom.com>
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>

Pull MMC updates from Chris Ball:
 "MMC highlights for 3.13:

  Core:
   - Improve runtime PM support, remove mmc_{suspend,resume}_host().
   - Add MMC_CAP_RUNTIME_RESUME, for delaying MMC resume until we're
     outside of the resume sequence (in runtime_resume) to decrease
     system resume time.

  Drivers:
   - dw_mmc: Support HS200 mode.
   - sdhci-eshdc-imx: Support SD3.0 SDR clock tuning, DDR on IMX6.
   - sdhci-pci: Add support for Intel Clovertrail and Merrifield"

* tag 'mmc-updates-for-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (108 commits)
  mmc: wbsd: Silence compiler warning
  mmc: core: Silence compiler warning in __mmc_switch
  mmc: sh_mmcif: Convert to clk_prepare|unprepare
  mmc: sh_mmcif: Convert to PM macros when defining dev_pm_ops
  mmc: dw_mmc: exynos: Revert the sdr_timing assignment
  mmc: sdhci: Avoid needless loop while handling SDIO interrupts in sdhci_irq
  mmc: core: Add MMC_CAP_RUNTIME_RESUME to resume at runtime_resume
  mmc: core: Improve runtime PM support during suspend/resume for sd/mmc
  mmc: core: Remove redundant mmc_power_up|off at runtime callbacks
  mmc: Don't force card to active state when entering suspend/shutdown
  MIPS: db1235: Don't use MMC_CLKGATE
  mmc: core: Remove deprecated mmc_suspend|resume_host APIs
  mmc: mmci: Move away from using deprecated APIs
  mmc: via-sdmmc: Move away from using deprecated APIs
  mmc: tmio: Move away from using deprecated APIs
  mmc: sh_mmcif: Move away from using deprecated APIs
  mmc: sdricoh_cs: Move away from using deprecated APIs
  mmc: rtsx: Remove redundant suspend and resume callbacks
  mmc: wbsd: Move away from using deprecated APIs
  mmc: pxamci: Remove redundant suspend and resume callbacks
  ...