Do not reconfigure the PLL in case it has been configured already
with the requested parameters.
In case of different PLL configuration do only the needed changes.
This can save considerable amount of time since we can avoid the
defined protocol (with delays) for the PLL configuration.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Store the last used mclk configuration for the PLL.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

If the ucb1x00 touchscreen is resumed while the touchscreen is being
touched, the main thread stops responding.  This occurs because two
things happen:

1. When we suspended, we were woken up, and executed the loop.
   Finding that the touchscreen was not pressed, we prepare to
   schedule for a maximum timeout, before being stopped in
   try_to_freeze().

2. an irq occurs, we disable the irq, and mark it as disabled,
   and wake the thread.  This wake occurs while the thread is
   still within __refrigerator()

3. The thread is unfrozen, and __refrigerator() sets the threads
   state back to INTERRUPTIBLE.

We then drop into schedule_timeout() with an infinite timeout and the
IRQ disabled.  This prevents any further screen touches activating
the thread.

Fix this by using kthread_freezable_should_stop() which handles the
freezing issues for us outside of the hotspot where the task state
matters.  Include a flag to ignore the touchscreen until it is
released to avoid sending unintended data to the application.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

gpiolib drivers should first set the output data before setting the
direction to avoid putting glitches on an output signal.  As an
additional bonus, we tweak the code to avoid unnecessary register
writes to the output and direction registers if they have no need
to be updated.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

We were not restoring the UCB1x00 gpio output data on resume, resulting
in incorrect GPIO output data after a resume.  Add the missing register
write.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The genirq layer complains if an interrupt handler returns with
interrupts enabled.  The UCB1x00 handler does just this, because
ucb1x00_enable() calls mcp_enable(), which uses spin_lock_irq()
rather than spin_lock_irqsave().  Convert this, and the divisor
setting functions to use spin_lock_irqsave().

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

This reverts commit 5dd7bf59e0e8563265b3e5b33276099ef628fcc7.

Conflicts:

	scripts/mod/file2alias.c

This change is wrong on many levels.  First and foremost, it causes a
regression.  On boot on Assabet, which this patch gives a codec id of
'ucb1x00', it gives:

	ucb1x00 ID not found: 1005

0x1005 is a valid ID for the UCB1300 device.

Secondly, this patch is way over the top in terms of complexity.  The
only device which has been seen to be connected with this MCP code is
the UCB1x00 (UCB1200, UCB1300 etc) devices, and they all use the same
driver.  Adding a match table, requiring the codec string to match the
hardware ID read out of the ID register, etc is completely over the top
when we can just read the hardware ID register.

This reverts commit af9081ae64b941d32239b947882cd59ba855c5db.

This revert is necessary to revert 5dd7bf59e0e8563265b3e5b33276099ef628fcc7.

Autogenerated GPG tag for Rusty D1ADB8F1: 15EE 8D6C AB0E 7F0C F999  BFCB D920 0E6C D1AD B8F1

* tag 'for-linus' of git://github.com/rustyrussell/linux:
  module_param: check that bool parameters really are bool.
  intelfbdrv.c: bailearly is an int module_param
  paride/pcd: fix bool verbose module parameter.
  module_param: make bool parameters really bool (drivers & misc)
  module_param: make bool parameters really bool (arch)
  module_param: make bool parameters really bool (core code)
  kernel/async: remove redundant declaration.
  printk: fix unnecessary module_param_name.
  lirc_parallel: fix module parameter description.
  module_param: avoid bool abuse, add bint for special cases.
  module_param: check type correctness for module_param_array
  modpost: use linker section to generate table.
  modpost: use a table rather than a giant if/else statement.
  modules: sysfs - export: taint, coresize, initsize
  kernel/params: replace DEBUGP with pr_debug
  module: replace DEBUGP with pr_debug
  module: struct module_ref should contains long fields
  module: Fix performance regression on modules with large symbol tables
  module: Add comments describing how the "strmap" logic works

Fix up conflicts in scripts/mod/file2alias.c due to the new linker-
generated table approach to adding __mod_*_device_table entries.  The
ARM sa11x0 mcp bus needed to be converted to that too.

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (59 commits)
  rtc: max8925: Add function to work as wakeup source
  mfd: Add pm ops to max8925
  mfd: Convert aat2870 to dev_pm_ops
  mfd: Still check other interrupts if we get a wm831x touchscreen IRQ
  mfd: Introduce missing kfree in 88pm860x probe routine
  mfd: Add S5M series configuration
  mfd: Add s5m series irq driver
  mfd: Add S5M core driver
  mfd: Improve mc13xxx dt binding document
  mfd: Fix stmpe section mismatch
  mfd: Fix stmpe build warning
  mfd: Fix STMPE I2c build failure
  mfd: Constify aat2870-core i2c_device_id table
  gpio: Add support for stmpe variant 801
  mfd: Add support for stmpe variant 801
  mfd: Add support for stmpe variant 610
  mfd: Add support for STMPE SPI interface
  mfd: Separate out STMPE controller and interface specific code
  misc: Remove max8997-muic sysfs attributes
  mfd: Remove unused wm831x_irq_data_to_mask_reg()
  ...

Fix up trivial conflict in drivers/leds/Kconfig due to addition of
LEDS_MAX8997 and LEDS_TCA6507 next to each other.