The PCAP Asic as present on EZX phones is a multi function device with
voltage regulators, ADC, touch screen controller, RTC, USB transceiver,
leds controller, and audio codec.

It has two SPI ports, typically one is connected to the application
processor and another to the baseband, this driver provides read/write
functions to its registers, irq demultiplexer and ADC
queueing/abstraction.

This chip is used on a lot of Motorola phones, it was manufactured by TI
as a custom product with the name PTWL93017, later this design evolved
into the ATLAS PMIC from Freescale (MC13783).

Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This adds a core driver for the AB3100 mixed-signal circuit
found in the ST-Ericsson U300 series platforms. This driver
is a singleton proxy for all accesses to the AB3100
sub-drivers which will be merged on top of this one, RTC,
regulators, battery and system power control, vibrator,
LEDs, and an ALSA codec.

Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Reviewed-by: Mike Rapoport <mike@compulab.co.il>
Reviewed-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

What the PCF05633 calls as a 'GPIO' is much more than the GPIO in the linux
sense and there are only 4 of them - which means, the gpiolib is not used
here.

Signed-off-by: Balaji Rao <balajirrao@openmoko.org>
Cc: Andy Green <andy@openmoko.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>

This patch adds basic support for the PCF50633 ADC. The subtractive mode
is not supported yet.

Since we don't have adc subsystem, it currently lives in drivers/mfd.

Signed-off-by: Balaji Rao <balajirrao@openmoko.org>
Cc: Andy Green <andy@openmoko.com>
Acked-by: Jonathan Cameron <jonathan.cameron@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>

This patch implements the core of the PCF50633 driver. This core driver has
generic register read/write functions and does interrupt management for its
sub devices.

Signed-off-by: Balaji Rao <balajirrao@openmoko.org>
Cc: Andy Green <andy@openmoko.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>

ove the menelaus driver from drivers/i2c/chips to drivers/mfd
since it's more of a multi-function device than anything else,
and since Jean is trying to vanish drivers/i2c/chips ASAP.

One way to think of these chips are as the PMIC family most
used with OMAP2 generation chips.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>

Move the tps65010 driver from drivers/i2c/chips to drivers/mfd
since it's more of a multi-function device than anything else,
and since Jean is trying to vanish drivers/i2c/chips ASAP.

One way to think of these chips are as the PMIC family most
used with OMAP1 generation chips.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>

Basic MFD framework for the MSP430 microcontroller firmware used
on the dm355evm board:

 - Provides an interface for other drivers: register read/write
   utilities, and register declarations.

 - Directly exports:
     * Many signals through the GPIO framework
         + LEDs
         + SW6 through gpio sysfs
	 + NTSC/nPAL jumper through gpio sysfs
	 + ... more could be added later, e.g. MMC signals
     * Child devices:
	+ LEDs, via leds-gpio child (and default triggers)
	+ RTC, via rtc-dm355evm child device
	+ Buttons and IR control, via dm355evm_keys

 - Supports power-off system call.  Use the reset button to power
   the board back up; the power supply LED will be on, but the
   MSP430 waits to re-activate the regulators.

 - On probe() this:
     * Announces firmware revision
     * Turns off the banked LEDs
     * Exports the resources noted above
     * Hooks the power-off support
     * Muxes tvp5146 -or- imager for video input

Unless the new tvp514x driver (tracked for mainline) is configured,
this assumes that some custom imager driver handles video-in.

This completely ignores the registers reporting the output voltages
on the various power supplies.  Someone could add a hwmon interface
if that seems useful.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>

This one was accidentally left out during the rc1 mfd merge.

Signed-off-by: Samuel Ortiz <sameo@openedhand.com>

- Move it into a separate file; clean and streamline it
 - Restructure the init code for reuse during secondary dispatch
 - Support both levels (primary, secondary) of IRQ dispatch
 - Use a workqueue for irq mask/unmask and trigger configuration

Code for two subchips currently share that secondary handler code.
One is the power subchip; its IRQs are now handled by this core,
courtesy of this patch.  The other is the GPIO module, which will
be supported through a later patch.

There are also minor changes to the header file, mostly related
to GPIO support; nothing yet in mainline cares about those.  A
few references to OMAP-specific symbols are disabled; when they
can all be removed, the TWL4030 support ceases being OMAP-specific.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>