Since commit 0166dc11be91 ("of: make CONFIG_OF user selectable"), it
is possible to test-build any driver which depends on OF on any
architecture by explicitly selecting OF. Therefore depending on
COMPILE_TEST as an alternative is no longer needed.

Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20241022124745.5d8d3778@endymion.delvare
Signed-off-by: Lee Jones <lee@kernel.org>

Add core MFD driver for the Board Controller found on some Congatec SMARC
module. This Board Controller provides functions like watchdog, GPIO, and
I2C busses.

This commit adds support only for the conga-SA7 module.

Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://lore.kernel.org/r/20241001-congatec-board-controller-v3-1-39ceceed5c47@bootlin.com
Signed-off-by: Lee Jones <lee@kernel.org>

The ADP5585 is a 10/11 input/output port expander with a built in keypad
matrix decoder, programmable logic, reset generator, and PWM generator.
This driver supports the chip by modelling it as an MFD device, with two
child devices for the GPIO and PWM functions.

The driver is derived from an initial implementation from NXP, available
in commit 8059835bee19 ("MLK-25917-1 mfd: adp5585: add ADI adp5585 core
support") in their BSP kernel tree. It has been extensively rewritten.

Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240722121100.2855-3-laurent.pinchart@ideasonboard.com
Signed-off-by: Lee Jones <lee@kernel.org>

Marvell 88PM886 is a PMIC which provides various functions such as
onkey, battery, charger and regulators. It is found for instance in the
samsung,coreprimevelte smartphone with which this was tested. Implement
basic support to allow for the use of regulators and onkey.

Signed-off-by: Karel Balej <balejk@matfyz.cz>
Link: https://lore.kernel.org/r/20240531175109.15599-3-balejk@matfyz.cz
Signed-off-by: Lee Jones <lee@kernel.org>

Introduce support for Cirrus Logic Device CS40L50: a
haptic driver with waveform memory, integrated DSP,
and closed-loop algorithms.

The MFD component registers and initializes the device.

Signed-off-by: James Ogletree <jogletre@opensource.cirrus.com>
Reviewed-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/20240620161745.2312359-4-jogletre@opensource.cirrus.com
Signed-off-by: Lee Jones <lee@kernel.org>

The ROHM BD96801 PMIC is highly customizable automotive grade PMIC
which integrates regulator and watchdog funtionalities.

Provide INTB IRQ and register accesses for regulator/watchdog drivers.

Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/c5260e2dd222e3c64cdf410802bba195637ccb93.1719473802.git.mazziesaccount@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>

Rework the pm8008 driver to match the new devicetree binding which no
longer describes internal details like interrupts and register offsets
(including which of the two consecutive I2C addresses the registers
belong to).

Instead make the interrupt controller implementation internal and pass
interrupts to the subdrivers using MFD cell resources.

Note that subdrivers may either get their resources, like register block
offsets, from the parent MFD or this can be included in the subdrivers
directly.

In the current implementation, the temperature alarm driver is generic
enough to just get its base address and alarm interrupt from the parent
driver, which already uses this information to implement the interrupt
controller.

The regulator driver, however, needs additional information like parent
supplies and regulator characteristics so in that case it is easier to
just augment its table with the regulator register base addresses.

Similarly, the current GPIO driver already holds the number of pins and
that lookup table can therefore also be extended with register offsets.

Note that subdrivers can now access the two regmaps by name, even if the
primary regmap is registered last so that it is returned by default when
no name is provided in lookups.

Finally, note that the temperature alarm and GPIO subdrivers need some
minor rework before they can be used with non-SPMI devices like the
PM8008. The temperature alarm MFD cell name specifically uses a "qpnp"
rather than "spmi" prefix to prevent binding until the driver has been
updated.

Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240608155526.12996-11-johan+linaro@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>