Pull pci updates from Bjorn Helgaas:
 "Enumeration:
   - Conserve IRQs by setting up portdrv IRQs only when there are users
     (Jan Kiszka)
   - Rework and simplify _OSC negotiation for control of PCIe features
     (Joerg Roedel)
   - Remove struct pci_dev.driver pointer since it's redundant with the
     struct device.driver pointer (Uwe Kleine-König)

  Resource management:
   - Coalesce contiguous host bridge apertures from _CRS to accommodate
     BARs that cover more than one aperture (Kai-Heng Feng)

  Sysfs:
   - Check CAP_SYS_ADMIN before parsing user input (Krzysztof
     Wilczyński)
   - Return -EINVAL consistently from "store" functions (Krzysztof
     Wilczyński)
   - Use sysfs_emit() in endpoint "show" functions to avoid buffer
     overruns (Kunihiko Hayashi)

  PCIe native device hotplug:
   - Ignore Link Down/Up caused by resets during error recovery so
     endpoint drivers can remain bound to the device (Lukas Wunner)

  Virtualization:
   - Avoid bus resets on Atheros QCA6174, where they hang the device
     (Ingmar Klein)
   - Work around Pericom PI7C9X2G switch packet drop erratum by using
     store and forward mode instead of cut-through (Nathan Rossi)
   - Avoid trying to enable AtomicOps on VFs; the PF setting applies to
     all VFs (Selvin Xavier)

  MSI:
   - Document that /sys/bus/pci/devices/.../irq contains the legacy INTx
     interrupt or the IRQ of the first MSI (not MSI-X) vector (Barry
     Song)

  VPD:
   - Add pci_read_vpd_any() and pci_write_vpd_any() to access anywhere
     in the possible VPD space; use these to simplify the cxgb3 driver
     (Heiner Kallweit)

  Peer-to-peer DMA:
   - Add (not subtract) the bus offset when calculating DMA address
     (Wang Lu)

  ASPM:
   - Re-enable LTR at Downstream Ports so they don't report Unsupported
     Requests when reset or hot-added devices send LTR messages
     (Mingchuang Qiao)

  Apple PCIe controller driver:
   - Add driver for Apple M1 PCIe controller (Alyssa Rosenzweig, Marc
     Zyngier)

  Cadence PCIe controller driver:
   - Return success when probe succeeds instead of falling into error
     path (Li Chen)

  HiSilicon Kirin PCIe controller driver:
   - Reorganize PHY logic and add support for external PHY drivers
     (Mauro Carvalho Chehab)
   - Support PERST# GPIOs for HiKey970 external PEX 8606 bridge (Mauro
     Carvalho Chehab)
   - Add Kirin 970 support (Mauro Carvalho Chehab)
   - Make driver removable (Mauro Carvalho Chehab)

  Intel VMD host bridge driver:
   - If IOMMU supports interrupt remapping, leave VMD MSI-X remapping
     enabled (Adrian Huang)
   - Number each controller so we can tell them apart in
     /proc/interrupts (Chunguang Xu)
   - Avoid building on UML because VMD depends on x86 bare metal APIs
     (Johannes Berg)

  Marvell Aardvark PCIe controller driver:
   - Define macros for PCI_EXP_DEVCTL_PAYLOAD_* (Pali Rohár)
   - Set Max Payload Size to 512 bytes per Marvell spec (Pali Rohár)
   - Downgrade PIO Response Status messages to debug level (Marek Behún)
   - Preserve CRS SV (Config Request Retry Software Visibility) bit in
     emulated Root Control register (Pali Rohár)
   - Fix issue in configuring reference clock (Pali Rohár)
   - Don't clear status bits for masked interrupts (Pali Rohár)
   - Don't mask unused interrupts (Pali Rohár)
   - Avoid code repetition in advk_pcie_rd_conf() (Marek Behún)
   - Retry config accesses on CRS response (Pali Rohár)
   - Simplify emulated Root Capabilities initialization (Pali Rohár)
   - Fix several link training issues (Pali Rohár)
   - Fix link-up checking via LTSSM (Pali Rohár)
   - Fix reporting of Data Link Layer Link Active (Pali Rohár)
   - Fix emulation of W1C bits (Marek Behún)
   - Fix MSI domain .alloc() method to return zero on success (Marek
     Behún)
   - Read entire 16-bit MSI vector in MSI handler, not just low 8 bits
     (Marek Behún)
   - Clear Root Port I/O Space, Memory Space, and Bus Master Enable bits
     at startup; PCI core will set those as necessary (Pali Rohár)
   - When operating as a Root Port, set class code to "PCI Bridge"
     instead of the default "Mass Storage Controller" (Pali Rohár)
   - Add emulation for PCI_BRIDGE_CTL_BUS_RESET since aardvark doesn't
     implement this per spec (Pali Rohár)
   - Add emulation of option ROM BAR since aardvark doesn't implement
     this per spec (Pali Rohár)

  MediaTek MT7621 PCIe controller driver:
   - Add MediaTek MT7621 PCIe host controller driver and DT binding
     (Sergio Paracuellos)

  Qualcomm PCIe controller driver:
   - Add SC8180x compatible string (Bjorn Andersson)
   - Add endpoint controller driver and DT binding (Manivannan
     Sadhasivam)
   - Restructure to use of_device_get_match_data() (Prasad Malisetty)
   - Add SC7280-specific pcie_1_pipe_clk_src handling (Prasad Malisetty)

  Renesas R-Car PCIe controller driver:
   - Remove unnecessary includes (Geert Uytterhoeven)

  Rockchip DesignWare PCIe controller driver:
   - Add DT binding (Simon Xue)

  Socionext UniPhier Pro5 controller driver:
   - Serialize INTx masking/unmasking (Kunihiko Hayashi)

  Synopsys DesignWare PCIe controller driver:
   - Run dwc .host_init() method before registering MSI interrupt
     handler so we can deal with pending interrupts left by bootloader
     (Bjorn Andersson)
   - Clean up Kconfig dependencies (Andy Shevchenko)
   - Export symbols to allow more modular drivers (Luca Ceresoli)

  TI DRA7xx PCIe controller driver:
   - Allow host and endpoint drivers to be modules (Luca Ceresoli)
   - Enable external clock if present (Luca Ceresoli)

  TI J721E PCIe driver:
   - Disable PHY when probe fails after initializing it (Christophe
     JAILLET)

  MicroSemi Switchtec management driver:
   - Return error to application when command execution fails because an
     out-of-band reset has cleared the device BARs, Memory Space Enable,
     etc (Kelvin Cao)
   - Fix MRPC error status handling issue (Kelvin Cao)
   - Mask out other bits when reading of management VEP instance ID
     (Kelvin Cao)
   - Return EOPNOTSUPP instead of ENOTSUPP from sysfs show functions
     (Kelvin Cao)
   - Add check of event support (Logan Gunthorpe)

  Miscellaneous:
   - Remove unused pci_pool wrappers, which have been replaced by
     dma_pool (Cai Huoqing)
   - Use 'unsigned int' instead of bare 'unsigned' (Krzysztof
     Wilczyński)
   - Use kstrtobool() directly, sans strtobool() wrapper (Krzysztof
     Wilczyński)
   - Fix some sscanf(), sprintf() format mismatches (Krzysztof
     Wilczyński)
   - Update PCI subsystem information in MAINTAINERS (Krzysztof
     Wilczyński)
   - Correct some misspellings (Krzysztof Wilczyński)"

* tag 'pci-v5.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (137 commits)
  PCI: Add ACS quirk for Pericom PI7C9X2G switches
  PCI: apple: Configure RID to SID mapper on device addition
  iommu/dart: Exclude MSI doorbell from PCIe device IOVA range
  PCI: apple: Implement MSI support
  PCI: apple: Add INTx and per-port interrupt support
  PCI: kirin: Allow removing the driver
  PCI: kirin: De-init the dwc driver
  PCI: kirin: Disable clkreq during poweroff sequence
  PCI: kirin: Move the power-off code to a common routine
  PCI: kirin: Add power_off support for Kirin 960 PHY
  PCI: kirin: Allow building it as a module
  PCI: kirin: Add MODULE_* macros
  PCI: kirin: Add Kirin 970 compatible
  PCI: kirin: Support PERST# GPIOs for HiKey970 external PEX 8606 bridge
  PCI: apple: Set up reference clocks when probing
  PCI: apple: Add initial hardware bring-up
  PCI: of: Allow matching of an interrupt-map local to a PCI device
  of/irq: Allow matching of an interrupt-map local to an interrupt controller
  irqdomain: Make of_phandle_args_to_fwspec() generally available
  PCI: Do not enable AtomicOps on VFs
  ...

Pull SCSI updates from James Bottomley:
 "This consists of the usual driver updates (ufs, smartpqi, lpfc,
  target, megaraid_sas, hisi_sas, qla2xxx) and minor updates and bug
  fixes.

  Notable core changes are the removal of scsi->tag which caused some
  churn in obsolete drivers and a sweep through all drivers to call
  scsi_done() directly instead of scsi->done() which removes a pointer
  indirection from the hot path and a move to register core sysfs files
  earlier, which means they're available to KOBJ_ADD processing, which
  necessitates switching all drivers to using attribute groups"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (279 commits)
  scsi: lpfc: Update lpfc version to 14.0.0.3
  scsi: lpfc: Allow fabric node recovery if recovery is in progress before devloss
  scsi: lpfc: Fix link down processing to address NULL pointer dereference
  scsi: lpfc: Allow PLOGI retry if previous PLOGI was aborted
  scsi: lpfc: Fix use-after-free in lpfc_unreg_rpi() routine
  scsi: lpfc: Correct sysfs reporting of loop support after SFP status change
  scsi: lpfc: Wait for successful restart of SLI3 adapter during host sg_reset
  scsi: lpfc: Revert LOG_TRACE_EVENT back to LOG_INIT prior to driver_resource_setup()
  scsi: ufs: ufshcd-pltfrm: Fix memory leak due to probe defer
  scsi: ufs: mediatek: Avoid sched_clock() misuse
  scsi: mpt3sas: Make mpt3sas_dev_attrs static
  scsi: scsi_transport_sas: Add 22.5 Gbps link rate definitions
  scsi: target: core: Stop using bdevname()
  scsi: aha1542: Use memcpy_{from,to}_bvec()
  scsi: sr: Add error handling support for add_disk()
  scsi: sd: Add error handling support for add_disk()
  scsi: target: Perform ALUA group changes in one step
  scsi: target: Replace lun_tg_pt_gp_lock with rcu in I/O path
  scsi: target: Fix alua_tg_pt_gps_count tracking
  scsi: target: Fix ordered tag handling
  ...

Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it go through appropriate helpers.

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

struct device supports attribute groups directly but does not support
struct device_attribute directly. Hence switch to attribute groups.

Link: https://lore.kernel.org/r/20211012233558.4066756-6-bvanassche@acm.org
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Conditional statements are faster than indirect calls. Hence call
scsi_done() directly.

Link: https://lore.kernel.org/r/20211007202923.2174984-7-bvanassche@acm.org
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

The only two drivers don't make use of the id parameter, so drop it.  This
is a step toward removing pci_dev->driver.

Link: https://lore.kernel.org/r/20211004125935.2300113-9-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>

The wrappers in include/linux/pci-dma-compat.h should go away.

The patch has been generated with the coccinelle script below and has been
hand modified to replace GFP_ with a correct flag.  It has been compile
tested.

When memory is allocated in 'mptfc_GetFcDevPage0()' GFP_KERNEL can be used
because it is already used in this function and no lock is acquired in the
between.

When memory is allocated in 'mptfc_GetFcPortPage0()' and
'mptfc_GetFcPortPage1()' GFP_KERNEL can be used because they already call
'mpt_config()' which has an explicit 'might_sleep()'.

While at it, also remove some useless casting.

@@ @@
-    PCI_DMA_BIDIRECTIONAL
+    DMA_BIDIRECTIONAL

@@ @@
-    PCI_DMA_TODEVICE
+    DMA_TO_DEVICE

@@ @@
-    PCI_DMA_FROMDEVICE
+    DMA_FROM_DEVICE

@@ @@
-    PCI_DMA_NONE
+    DMA_NONE

@@
expression e1, e2, e3;
@@
-    pci_alloc_consistent(e1, e2, e3)
+    dma_alloc_coherent(&e1->dev, e2, e3, GFP_)

@@
expression e1, e2, e3;
@@
-    pci_zalloc_consistent(e1, e2, e3)
+    dma_alloc_coherent(&e1->dev, e2, e3, GFP_)

@@
expression e1, e2, e3, e4;
@@
-    pci_free_consistent(e1, e2, e3, e4)
+    dma_free_coherent(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_map_single(e1, e2, e3, e4)
+    dma_map_single(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_unmap_single(e1, e2, e3, e4)
+    dma_unmap_single(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4, e5;
@@
-    pci_map_page(e1, e2, e3, e4, e5)
+    dma_map_page(&e1->dev, e2, e3, e4, e5)

@@
expression e1, e2, e3, e4;
@@
-    pci_unmap_page(e1, e2, e3, e4)
+    dma_unmap_page(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_map_sg(e1, e2, e3, e4)
+    dma_map_sg(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_unmap_sg(e1, e2, e3, e4)
+    dma_unmap_sg(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_dma_sync_single_for_cpu(e1, e2, e3, e4)
+    dma_sync_single_for_cpu(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_dma_sync_single_for_device(e1, e2, e3, e4)
+    dma_sync_single_for_device(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_dma_sync_sg_for_cpu(e1, e2, e3, e4)
+    dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_dma_sync_sg_for_device(e1, e2, e3, e4)
+    dma_sync_sg_for_device(&e1->dev, e2, e3, e4)

@@
expression e1, e2;
@@
-    pci_dma_mapping_error(e1, e2)
+    dma_mapping_error(&e1->dev, e2)

@@
expression e1, e2;
@@
-    pci_set_dma_mask(e1, e2)
+    dma_set_mask(&e1->dev, e2)

@@
expression e1, e2;
@@
-    pci_set_consistent_dma_mask(e1, e2)
+    dma_set_coherent_mask(&e1->dev, e2)

Link: https://lore.kernel.org/r/95afc589713ade2110e7812159ce3e9ab453ec18.1623568121.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Variable rc is set to '-1', but this value is never read as it is
overwritten later. Hence it is a redundant assignment and can be removed.

Clean up the following clang-analyzer warning:

drivers/message/fusion/mptbase.c:6996:2: warning: Value stored to 'rc'
is never read [clang-analyzer-deadcode.DeadStores].

Link: https://lore.kernel.org/r/1620814327-25427-1-git-send-email-jiapeng.chong@linux.alibaba.com
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Fix kernel-doc warnings, spellos, and typos.

../drivers/message/fusion/mptsas.c:432: warning: Function parameter or member 'sas_address' not described in 'mptsas_find_portinfo_by_sas_address'
../drivers/message/fusion/mptsas.c:432: warning: Excess function parameter 'handle' description in 'mptsas_find_portinfo_by_sas_address'
../drivers/message/fusion/mptsas.c:581: warning: Function parameter or member 'slot' not described in 'mptsas_add_device_component'
../drivers/message/fusion/mptsas.c:581: warning: Function parameter or member 'enclosure_logical_id' not described in 'mptsas_add_device_component'
../drivers/message/fusion/mptsas.c:678: warning: Function parameter or member 'starget' not described in 'mptsas_add_device_component_starget_ir'
../drivers/message/fusion/mptsas.c:678: warning: Excess function parameter 'channel' description in 'mptsas_add_device_component_starget_ir'
../drivers/message/fusion/mptsas.c:678: warning: Excess function parameter 'id' description in 'mptsas_add_device_component_starget_ir'
../drivers/message/fusion/mptsas.c:990: warning: Function parameter or member 'ioc' not described in 'mptsas_find_vtarget'
../drivers/message/fusion/mptsas.c:990: warning: Function parameter or member 'channel' not described in 'mptsas_find_vtarget'
../drivers/message/fusion/mptsas.c:990: warning: Function parameter or member 'id' not described in 'mptsas_find_vtarget'
../drivers/message/fusion/mptsas.c:990: warning: expecting prototype for csmisas_find_vtarget(). Prototype was for mptsas_find_vtarget() instead
../drivers/message/fusion/mptsas.c:1064: warning: Function parameter or member 'ioc' not described in 'mptsas_target_reset'
../drivers/message/fusion/mptsas.c:1064: warning: Function parameter or member 'channel' not described in 'mptsas_target_reset'
../drivers/message/fusion/mptsas.c:1064: warning: Function parameter or member 'id' not described in 'mptsas_target_reset'
../drivers/message/fusion/mptsas.c:1135: warning: Function parameter or member 'ioc' not described in 'mptsas_target_reset_queue'
../drivers/message/fusion/mptsas.c:1135: warning: Function parameter or member 'sas_event_data' not described in 'mptsas_target_reset_queue'
../drivers/message/fusion/mptsas.c:1217: warning: Function parameter or member 'mf' not described in 'mptsas_taskmgmt_complete'
../drivers/message/fusion/mptsas.c:1217: warning: Function parameter or member 'mr' not described in 'mptsas_taskmgmt_complete'
../drivers/message/fusion/mptsas.c:1311: warning: Function parameter or member 'ioc' not described in 'mptsas_ioc_reset'
../drivers/message/fusion/mptsas.c:1311: warning: Function parameter or member 'reset_phase' not described in 'mptsas_ioc_reset'
../drivers/message/fusion/mptsas.c:1311: warning: expecting prototype for mptscsih_ioc_reset(). Prototype was for mptsas_ioc_reset() instead
../drivers/message/fusion/mptsas.c:1951: warning: expecting prototype for mptsas_mptsas_eh_timed_out(). Prototype was for mptsas_eh_timed_out() instead
../drivers/message/fusion/mptsas.c:3623: warning: Function parameter or member 'fw_event' not described in 'mptsas_send_expander_event'
../drivers/message/fusion/mptsas.c:3623: warning: Excess function parameter 'ioc' description in 'mptsas_send_expander_event'
../drivers/message/fusion/mptsas.c:3623: warning: Excess function parameter 'expander_data' description in 'mptsas_send_expander_event'
../drivers/message/fusion/mptsas.c:4010: warning: Excess function parameter 'sas_address' description in 'mptsas_scan_sas_topology'
../drivers/message/fusion/mptsas.c:4783: warning: Function parameter or member 'issue_reset' not described in 'mptsas_issue_tm'
../drivers/message/fusion/mptsas.c:4856: warning: Function parameter or member 'fw_event' not described in 'mptsas_broadcast_primitive_work'
../drivers/message/fusion/mptsas.c:4856: warning: Excess function parameter 'work' description in 'mptsas_broadcast_primitive_work'

mptsas.c:984: warning: missing initial short description on line:
 * csmisas_find_vtarget
mptsas.c:993: warning: expecting prototype for csmisas_find_vtarget(). Prototype
 was for mptsas_find_vtarget() instead
mptsas.c:1053: warning: missing initial short description on line:
 * mptsas_target_reset
mptsas.c:1057: warning: contents before sections
mptsas.c:1125: warning: missing initial short description on line:
 * mptsas_target_reset_queue
mptsas.c:1131: warning: contents before sections
mptsas.c:1308: warning: missing initial short description on line:
 * mptsas_ioc_reset

Link: https://lore.kernel.org/r/20210418203259.835-1-rdunlap@infradead.org
Cc: Sathya Prakash <sathya.prakash@broadcom.com>
Cc: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Cc: MPT-FusionLinux.pdl@broadcom.com
Cc: linux-scsi@vger.kernel.org
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Fix the following gcc warning:

drivers/message/fusion/mptsas.c:783:14: warning: variable ‘vtarget’ set
but not used [-Wunused-but-set-variable].

Link: https://lore.kernel.org/r/1618207146-96542-1-git-send-email-jiapeng.chong@linux.alibaba.com
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>