Pull device-mapper fixes from Mike Snitzer:
 "Quite a few fixes for DM's blk-mq support thanks to extra DM multipath
  testing from Junichi Nomura and Bart Van Assche.

  Also fix a casting bug in dm_merge_bvec() that could cause only a
  single page to be added to a bio (Joe identified this while testing
  dm-cache writeback)"

* tag 'dm-4.1-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
  dm: fix casting bug in dm_merge_bvec()
  dm: fix reload failure of 0 path multipath mapping on blk-mq devices
  dm: fix false warning in free_rq_clone() for unmapped requests
  dm: requeue from blk-mq dm_mq_queue_rq() using BLK_MQ_RQ_QUEUE_BUSY
  dm mpath: fix leak of dm_mpath_io structure in blk-mq .queue_rq error path
  dm: fix NULL pointer when clone_and_map_rq returns !DM_MAPIO_REMAPPED
  dm: run queue on re-queue

dm_merge_bvec() was originally added in f6fccb ("dm: introduce
merge_bvec_fn").  In that commit a value in sectors is converted to
bytes using << 9, and then assigned to an int.  This code made
assumptions about the value of BIO_MAX_SECTORS.

A later commit 148e51 ("dm: improve documentation and code clarity in
dm_merge_bvec") was meant to have no functional change but it removed
the use of BIO_MAX_SECTORS in favor of using queue_max_sectors().  At
this point the cast from sector_t to int resulted in a zero value.  The
fallout being dm_merge_bvec() would only allow a single page to be added
to a bio.

This interim fix is minimal for the benefit of stable@ because the more
comprehensive cleanup of passing a sector_t to all DM targets' merge
function will impact quite a few DM targets.

Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 3.19+

dm-multipath accepts 0 path mapping.

  # echo '0 2097152 multipath 0 0 0 0' | dmsetup create newdev

Such a mapping can be used to release underlying devices while still
holding requests in its queue until working paths come back.

However, once the multipath device is created over blk-mq devices,
it rejects reloading of 0 path mapping:

  # echo '0 2097152 multipath 0 0 1 1 queue-length 0 1 1 /dev/sda 1' \
      | dmsetup create mpath1
  # echo '0 2097152 multipath 0 0 0 0' | dmsetup load mpath1
  device-mapper: reload ioctl on mpath1 failed: Invalid argument
  Command failed

With following kernel message:
  device-mapper: ioctl: can't change device type after initial table load.

DM tries to inherit the current table type using dm_table_set_type()
but it doesn't work as expected because of unnecessary check about
whether the target type is hybrid or not.

Hybrid type is for targets that work as either request-based or bio-based
and not required for blk-mq or non blk-mq checking.

Fixes: 65803c205983 ("dm table: train hybrid target type detection to select blk-mq if appropriate")
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>

Pull m,ore md bugfixes gfrom Neil Brown:
 "Assorted fixes for new RAID5 stripe-batching functionality.

  Unfortunately this functionality was merged a little prematurely.  The
  necessary testing and code review is now complete (or as complete as
  it can be) and to code passes a variety of tests and looks quite
  sensible.

  Also a fix for some recent locking changes - a race was introduced
  which causes a reshape request to sometimes fail.  No data safety
  issues"

* tag 'md/4.1-rc5-fixes' of git://neil.brown.name/md:
  md: fix race when unfreezing sync_action
  md/raid5: break stripe-batches when the array has failed.
  md/raid5: call break_stripe_batch_list from handle_stripe_clean_event
  md/raid5: be more selective about distributing flags across batch.
  md/raid5: add handle_flags arg to break_stripe_batch_list.
  md/raid5: duplicate some more handle_stripe_clean_event code in break_stripe_batch_list
  md/raid5: remove condition test from check_break_stripe_batch_list.
  md/raid5: Ensure a batch member is not handled prematurely.
  md/raid5: close race between STRIPE_BIT_DELAY and batching.
  md/raid5: ensure whole batch is delayed for all required bitmap updates.

When stacking request-based dm device on non blk-mq device and
device-mapper target could not map the request (error target is used,
multipath target with all paths down, etc), the WARN_ON_ONCE() in
free_rq_clone() will trigger when it shouldn't.

The warning was added by commit aa6df8d ("dm: fix free_rq_clone() NULL
pointer when requeueing unmapped request").  But free_rq_clone() with
clone->q == NULL is valid usage for the case where
dm_kill_unmapped_request() initiates request cleanup.

Fix this false warning by just removing the WARN_ON -- it only generated
false positives and was never useful in catching the intended case
(completing clone request not being mapped e.g. clone->q being NULL).

Fixes: aa6df8d ("dm: fix free_rq_clone() NULL pointer when requeueing unmapped request")
Reported-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reported-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>

A recent change removed the need for locking around writing
to "sync_action" (and various other places), but introduced a
subtle race.
When e.g. setting 'reshape' on a 'frozen' array, the 'frozen'
flag is cleared before 'reshape' is set, so the md thread can
get in and start trying recovery - which isn't wanted.

So instead of clearing MD_RECOVERY_FROZEN for any command
except 'frozen', only clear it when each specific command
is parsed.  This allows the handling of 'reshape' to clear
the bit while a lock is held.

Also remove some places where we set MD_RECOVERY_NEEDED,
as it is always set on non-error exit of the function.


Signed-off-by: NeilBrown <neilb@suse.de>
Fixes: 6791875e2e53 ("md: make reconfig_mutex optional for writes to md sysfs files.")

Once the array has too much failure, we need to break
stripe-batches up so they can all be dealt with.

Signed-off-by: NeilBrown <neilb@suse.de>

Now that the code in break_stripe_batch_list() is nearly identical
to the end of handle_stripe_clean_event, replace the later
with a function call.

The only remaining difference of any interest is the masking that is
applieds to dev[i].flags copied from head_sh.
R5_WriteError certainly isn't wanted as it is set per-stripe, not
per-patch.  R5_Overlap isn't wanted as it is explicitly handled.

Signed-off-by: NeilBrown <neilb@suse.de>

When a batch of stripes is broken up, we keep some of the flags
that were per-stripe, and copy other flags from the head to all
others.

This only happens while a stripe is being handled, so many of the
flags are irrelevant.

The "SYNC_FLAGS" (which I've renamed to make it clear there are
several) and STRIPE_DEGRADED are set per-stripe and so need to be
preserved.  STRIPE_INSYNC is the only flag that is set on the head
that needs to be propagated to all others.

For safety, add a WARN_ON if others are set, except:
 STRIPE_HANDLE - this is safe and per-stripe and we are going to set
      in several cases anyway
 STRIPE_INSYNC
 STRIPE_IO_STARTED - this is just a hint and doesn't hurt.
 STRIPE_ON_PLUG_LIST
 STRIPE_ON_RELEASE_LIST - It is a point pointless for a batched
           stripe to be on one of these lists, but it can happen
           as can be safely ignored.

Signed-off-by: NeilBrown <neilb@suse.de>

When we break a stripe_batch_list we sometimes want to set
STRIPE_HANDLE on the individual stripes, and sometimes not.

So pass a 'handle_flags' arg.  If it is zero, always set STRIPE_HANDLE
(on non-head stripes).  If not zero, only set it if any of the given
flags are present.

Signed-off-by: NeilBrown <neilb@suse.de>