If you prepare_to_wait() after a previous prepare_to_wait(),
but before calling schedule(), you get warning:

  do not call blocking ops when !TASK_RUNNING; state=2

This is appropriate as it is often a bug.  The event that the
first prepare_to_wait() expects might wake up the schedule following
the second prepare_to_wait(), which could be confusing.

However if both prepare_to_wait()s are part of simple wait_event()
loops, and if the inner one is rarely called, then there is
no problem.  The inner loop is too simple to get confused by
a stray wakeup, and the outer loop won't spin unduly because the
inner doesnt affect it often.

This pattern occurs in both raid1.c and raid10.c in the use of
flush_pending_writes().

The warning can be silenced by setting current->state to TASK_RUNNING.

Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>

flush_pending_writes isn't always called with block plug, so add it, and plug
works in nested way.

Signed-off-by: Shaohua Li <shli@fb.com>

Suspending the entire device for resync could take
too long. Resync in small chunks.

cluster's resync window is maintained in r10conf as
cluster_sync_low and cluster_sync_high, and processed
in raid10's sync_request(). If the current resync is
outside the cluster resync window:

1. Set the cluster_sync_low to curr_resync_completed.
2. Set cluster_sync_high to cluster_sync_low + stripe
   size.
3. Send a message to all nodes so they may add it in
   their suspension list.

Note:
We only support "near" raid10 so far, resync a far or
offset raid10 array could have trouble. So raid10_run
checks the layout of clustered raid10, it will refuse
to run if the layout is not correct.

With the "near" layout we process one stripe at a time
progressing monotonically through the address space.
So we can have a sliding window of whole-stripes which
moves through the array suspending IO on other nodes,
and both resync which uses array addresses and recovery
which uses device addresses can stay within this window.

Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>

If there is a resync going on, all nodes must suspend
writes to the range. This is recorded in suspend_info
and suspend_list.

If there is an I/O within the ranges of any of the
suspend_info, area_resyncing will return 1.

Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>

Just like clustered raid1, it is impossible for cluster raid10
to choose the best device for read balance when the area of
array is resyncing. Because we cannot trust the data to be the
same on all devices at that time, so we choose just the first
one to use, so set do_balance to 0.

Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>

The '2' argument means "wake up anything that is waiting".
This is an inelegant part of the design and was added
to help support management of suspend_lo/suspend_hi setting.
Now that suspend_lo/hi is managed in mddev_suspend/resume,
that need is gone.
These is still a couple of places where we call 'quiesce'
with an argument of '2', but they can safely be changed to
call ->quiesce(.., 1); ->quiesce(.., 0) which
achieve the same result at the small cost of pausing IO
briefly.

This removes a small "optimization" from suspend_{hi,lo}_store,
but it isn't clear that optimization served a useful purpose.
The code now is a lot clearer.

Suggested-by: Shaohua Li <shli@kernel.org>
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>

Variables dev and bio_last_sector are assigned values that are never
read and hence these are redundant variables and can be removed.
Also remove the duplicated initialization of sectors, the latter
assignment is identical to the first and can be removed.

Cleans up 3 clang build warnings:
Value stored to 'dev' is never read
Value stored to 'bio_last_sector' is never read
Value stored to 'sectors' during its initialization is never read

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Shaohua Li <shli@fb.com>

Motivated by the desire to illiminate the imprecise nature of
DM-specific patches being unnecessarily sent to both the MD maintainer
and mailing-list.  Which is born out of the fact that DM files also
reside in drivers/md/

Now all MD-specific files in drivers/md/ start with either "raid" or
"md-" and the MAINTAINERS file has been updated accordingly.

Shaohua: don't change module name

Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Shaohua Li <shli@fb.com>

The raid10 driver can't be built with clang since it uses a variable
length array in a structure (VLAIS):

drivers/md/raid10.c:4583:17: error: fields must have a constant size:
  'variable length array in structure' extension will never be supported

Allocate the r10bio struct with kmalloc instead of using the VLAIS
construct.

Shaohua: set the MD_RECOVERY_INTR bit
Neil Brown: use GFP_NOIO

Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Shaohua Li <shli@fb.com>

Pull MD updates from Shaohua Li:
 "This update mainly fixes bugs:

   - Make raid5 ppl support several ppl from Pawel

   - Several raid5-cache bug fixes from Song

   - Bitmap fixes from Neil and Me

   - One raid1/10 regression fix since 4.12 from Me

   - Other small fixes and cleanup"

* tag 'md/4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
  md/bitmap: disable bitmap_resize for file-backed bitmaps.
  raid5-ppl: Recovery support for multiple partial parity logs
  md: Runtime support for multiple ppls
  md/raid0: attach correct cgroup info in bio
  lib/raid6: align AVX512 constants to 512 bits, not bytes
  raid5: remove raid5_build_block
  md/r5cache: call mddev_lock/unlock() in r5c_journal_mode_show
  md: replace seq_release_private with seq_release
  md: notify about new spare disk in the container
  md/raid1/10: reset bio allocated from mempool
  md/raid5: release/flush io in raid5_do_work()
  md/bitmap: copy correct data for bitmap super