leds-lp55xx-common.c:(.text+0x9d): undefined reference to `i2c_smbus_read_byte_data'
leds-lp55xx-common.c:(.text+0x8fc): undefined reference to `i2c_smbus_write_byte_data'

These errors happened when I2C=m and LEDS_LP55XX_COMMON=y, so
prevent that from being possible.

Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: linux-leds@vger.kernel.org
Cc: Milo Kim <milo.kim@ti.com>
Cc: Mathias Nyman <mathias.nyman@nokia.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>

This adds basic support for LEDs on the front side of CZ.NIC's Turris
Omnia router.

There are 12 RGB LEDs. The controller supports HW triggering mode for
the LEDs, but this driver does not support it yet, and sets all the LEDs
defined in device-tree into SW mode upon probe.

This driver uses the multicolor LED framework.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>

Add multicolor framework support for the lp55xx family.

Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>

Introduce a multicolor class that groups colored LEDs
within a LED node.

The multicolor class groups monochrome LEDs and allows controlling two
aspects of the final combined color: hue and lightness. The former is
controlled via the intensity file and the latter is controlled
via brightness file.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
[squashed leds: multicolor: Fix camel case in documentation in]

This commit adds support for AWINIC AW2013 3-channel LED driver.
The chip supports 3 PWM channels and is controlled with I2C.

Signed-off-by: Nikita Travkin <nikitos.tr@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>

Add a driver for the SGMICRO SGM3140 Buck/Boost Charge Pump LED driver.

This device is controlled by two GPIO pins, one for enabling and the
second one for switching between torch and flash mode.

Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Pavel Machek <pavel@ucw.cz>

This adds support for controlling the LEDs attached to the Embedded
Controller on a Dell Wyse 3020 "Ariel" board.

Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Pavel Machek <pavel@ucw.cz>

This patch implemenets a driver to support the front panel LEDs of
SGI Octane (IP30) workstations.

Reviewed-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>

This driver adds support for the LED operational mode of the
tps6105x MFD device.

Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>

Update the Kconfig to be consistent in the case of using
"LED" in the Kconfig.  LED is an acronym and should be
capitalized.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>