linux.git/drivers/input/joystick, branch v3.5-rc2

i2c: Split I2C_M_NOSTART support out of I2C_FUNC_PROTOCOL_MANGLING

2012-05-30T08:55:34+00:00

Since there are uses for I2C_M_NOSTART which are much more sensible and
standard than most of the protocol mangling functionality (the main one
being gather writes to devices where something like a register address
needs to be inserted before a block of data) create a new I2C_FUNC_NOSTART
for this feature and update all the users to use it.

Also strengthen the disrecommendation of the protocol mangling while we're
at it.

In the case of regmap-i2c we remove the requirement for mangling as
I2C_M_NOSTART is the only mangling feature which is being used.

Signed-off-by: Mark Brown 
Acked-by: Wolfram Sang 
Signed-off-by: Jean Delvare

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input

2012-05-24T17:34:29+00:00

Pull input layer updates from Dmitry Torokhov:
 - a bunch of new drivers (DA9052/53 touchscreenn controller, Synaptics
   Navpoint, LM8333 keypads, Wacom I2C touhscreen);
 - updates to existing touchpad drivers (ALPS, Sntelic);
 - Wacom driver now supports Intuos5;
 - device-tree bindings in numerous drivers;
 - other cleanups and fixes.

Fix annoying conflict in drivers/input/tablet/wacom_wac.c that I think
implies that the input layer device naming is broken, but let's see.  I
brough it up with Dmitry.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (57 commits)
  Input: matrix-keymap - fix building keymaps
  Input: spear-keyboard - document DT bindings
  Input: spear-keyboard - add device tree bindings
  Input: matrix-keymap - wire up device tree support
  Input: matrix-keymap - uninline and prepare for device tree support
  Input: adp5588 - add support for gpio names
  Input: omap-keypad - dynamically handle register offsets
  Input: synaptics - fix compile warning
  MAINTAINERS: adjust input-related patterns
  Input: ALPS - switch to using input_mt_report_finger_count
  Input: ALPS - add semi-MT support for v4 protocol
  Input: Add Synaptics NavPoint (PXA27x SSP/SPI) driver
  Input: atmel_mxt_ts - dump each message on just 1 line
  Input: atmel_mxt_ts - do not read extra (checksum) byte
  Input: atmel_mxt_ts - verify object size in mxt_write_object
  Input: atmel_mxt_ts - only allow root to update firmware
  Input: atmel_mxt_ts - use CONFIG_PM_SLEEP
  Input: sentelic - report device's production serial number
  Input: tl6040-vibra - Device Tree support
  Input: evdev - properly handle read/write with count 0
  ...

USB: input: xpad.c: fix up dev_* messages

2012-05-04T22:32:53+00:00

Previously I had made the struct device point to the input device, but
after talking with Dmitry, he said that the USB device would make more
sense for this driver to point to.  So converted it to use that instead.

CC: Dmitry Torokhov 
CC: "Magnus Hörlin" 
CC: Rusty Russell 
CC: Mauro Carvalho Chehab 
Signed-off-by: Greg Kroah-Hartman

USB: input: iforce: fix up dev_* messages

2012-05-04T22:23:04+00:00

Previously I had made the struct device point to the input device, but
after talking with Dmitry, he said that the USB device would make more
sense for this driver to point to.  So converted it to use that instead.

Cc: Dmitry Torokhov 
Signed-off-by: Greg Kroah-Hartman

USB: xpad.c: remove dbg() usage

2012-05-02T04:32:59+00:00

dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.

CC: Dmitry Torokhov 
CC: "Magnus Hörlin" 
CC: Rusty Russell 
CC: Mauro Carvalho Chehab 
Signed-off-by: Greg Kroah-Hartman

USB: iforce: remove dbg() usage

2012-05-02T04:31:55+00:00

dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.

Cc: Dmitry Torokhov 
Signed-off-by: Greg Kroah-Hartman

USB: input: xpad.c: fix up dev_err() usage

2012-05-02T00:56:34+00:00

We should always reference the input device for dev_err(), not the USB
device.  Fix up the places where I got this wrong.

Reported-by: Dmitry Torokhov 
CC: "Magnus Hörlin" 
CC: Rusty Russell 
CC: Mauro Carvalho Chehab 
Signed-off-by: Greg Kroah-Hartman

USB: input: joystick: iforce: fix up dev_err() usages

2012-05-01T22:40:57+00:00

We should always reference the input device for dev_err(), not the USB
device.  Fix up the places where I got this wrong.

Reported-by: Dmitry Torokhov 
Signed-off-by: Greg Kroah-Hartman

USB: xpad.c: remove err() usage

2012-04-25T21:48:23+00:00

err() was a very old USB-specific macro that I thought had
gone away.  This patch removes it from being used in the
driver and uses dev_err() instead.

CC: Dmitry Torokhov 
CC: "Magnus Hörlin" 
CC: Rusty Russell 
CC: Mauro Carvalho Chehab 
CC: Chris Moeller 
Signed-off-by: Greg Kroah-Hartman

USB: iforce: remove err() usage

2012-04-25T21:34:49+00:00

err() was a very old USB-specific macro that I thought had gone away.
This patch removes it from being used in the driver and uses dev_err()
instead.

Cc: Dmitry Torokhov 
Signed-off-by: Greg Kroah-Hartman