ipoib_transport_dev_init() calls ipoib_cm_dev_init(), so it needs to
call ipoib_cm_dev_cleanup() to unwind that on the error path.

Found by Dotan Barak of Mellanox.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

New Cisco IB SRP targets use the Cisco OUI 00-1b-0d but still need the
Topspin workarounds.  Add this OUI to srp_target_is_topspin().

Signed-off-by: Roland Dreier <rolandd@cisco.com>

Wrap the checking for Mellanox and Topspin OUIs to decide whether to
use a workaround into helper functions.  This will make it cleaner to
add a new OUI to check (as we need to do now that some targets with a
Cisco OUI still need the Topspin workarounds).

Signed-off-by: Roland Dreier <rolandd@cisco.com>

This prevents the iscsi modules from being unloaded while
there are active mounts from an iscsi target.

Signed-off-by: Olaf Kirch <olaf.kirch@oracle.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Slab destructors were no longer supported after Christoph's
c59def9f222d44bb7e2f0a559f2906191a0862d7 change. They've been
BUGs for both slab and slub, and slob never supported them
either.

This rips out support for the dtor pointer from kmem_cache_create()
completely and fixes up every single callsite in the kernel (there were
about 224, not including the slab allocator definitions themselves,
or the documentation references).

Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Make iser_conn_release() and iser_start_rdma_unaligned_sg() static,
since they are only used in the .c file where they are defined.  In
addition to being a cleanup, this even shrinks the generated code by
allowing the single call of iser_start_rdma_unaligned_sg() to be
inlined into its callsite.  On x86_64:

add/remove: 0/1 grow/shrink: 1/0 up/down: 466/-533 (-67)
function                                     old     new   delta
iser_reg_rdma_mem                           1518    1984    +466
iser_start_rdma_unaligned_sg                 533       -    -533

Signed-off-by: Roland Dreier <rolandd@cisco.com>

* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (166 commits)
  [SCSI] ibmvscsi: convert to use the data buffer accessors
  [SCSI] dc395x: convert to use the data buffer accessors
  [SCSI] ncr53c8xx: convert to use the data buffer accessors
  [SCSI] sym53c8xx: convert to use the data buffer accessors
  [SCSI] ppa: coding police and printk levels
  [SCSI] aic7xxx_old: remove redundant GFP_ATOMIC from kmalloc
  [SCSI] i2o: remove redundant GFP_ATOMIC from kmalloc from device.c
  [SCSI] remove the dead CYBERSTORMIII_SCSI option
  [SCSI] don't build scsi_dma_{map,unmap} for !HAS_DMA
  [SCSI] Clean up scsi_add_lun a bit
  [SCSI] 53c700: Remove printk, which triggers because of low scsi clock on SNI RMs
  [SCSI] sni_53c710: Cleanup
  [SCSI] qla4xxx: Fix underrun/overrun conditions
  [SCSI] megaraid_mbox: use mutex instead of semaphore
  [SCSI] aacraid: add 51245, 51645 and 52245 adapters to documentation.
  [SCSI] qla2xxx: update version to 8.02.00-k1.
  [SCSI] qla2xxx: add support for NPIV
  [SCSI] stex: use resid for xfer len information
  [SCSI] Add Brownie 1200U3P to blacklist
  [SCSI] scsi.c: convert to use the data buffer accessors
  ...

The IB CM should include the HCA ACK delay when calculating the local
ACK timeout value to use for RC QPs.  If the HCA ACK delay is large
enough relative to the packet life time, then if it is not taken into
account, the calculated timeout value ends up being too small, which
can result in "retry exceeded" errors.

Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

InfiniBand HCAs replicate multicast packets back to the QP that sent
them if that QP is attached to the destination multicast group.  This
means that IPoIB multicasts are often replicated back to the receive
queue of the interface that generated them.  To avoid confusing the
network stack, we drop these duplicates within the IPoIB driver.

However, there's no reason to free the skb that received the duplicate
and then immediately allocate a new skb to post to the receive queue.
We can be more efficient and just repost the same skb.

Signed-off-by: Roland Dreier <rolandd@cisco.com>

Fix

    drivers/infiniband/ulp/ipoib/ipoib_cm.c:1151: warning: unused variable 'dev'

by getting rid of the variable dev, which is only used if CONFIG_IPV6
is enabled, and replacing the one use of it with the value it is
assigned, namely priv->dev.

Signed-off-by: Roland Dreier <rolandd@cisco.com>