This prevents the iscsi modules from being unloaded while
there are active mounts from an iscsi target.

Signed-off-by: Olaf Kirch <olaf.kirch@oracle.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Slab destructors were no longer supported after Christoph's
c59def9f222d44bb7e2f0a559f2906191a0862d7 change. They've been
BUGs for both slab and slub, and slob never supported them
either.

This rips out support for the dtor pointer from kmem_cache_create()
completely and fixes up every single callsite in the kernel (there were
about 224, not including the slab allocator definitions themselves,
or the documentation references).

Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Make iser_conn_release() and iser_start_rdma_unaligned_sg() static,
since they are only used in the .c file where they are defined.  In
addition to being a cleanup, this even shrinks the generated code by
allowing the single call of iser_start_rdma_unaligned_sg() to be
inlined into its callsite.  On x86_64:

add/remove: 0/1 grow/shrink: 1/0 up/down: 466/-533 (-67)
function                                     old     new   delta
iser_reg_rdma_mem                           1518    1984    +466
iser_start_rdma_unaligned_sg                 533       -    -533

Signed-off-by: Roland Dreier <rolandd@cisco.com>

* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (166 commits)
  [SCSI] ibmvscsi: convert to use the data buffer accessors
  [SCSI] dc395x: convert to use the data buffer accessors
  [SCSI] ncr53c8xx: convert to use the data buffer accessors
  [SCSI] sym53c8xx: convert to use the data buffer accessors
  [SCSI] ppa: coding police and printk levels
  [SCSI] aic7xxx_old: remove redundant GFP_ATOMIC from kmalloc
  [SCSI] i2o: remove redundant GFP_ATOMIC from kmalloc from device.c
  [SCSI] remove the dead CYBERSTORMIII_SCSI option
  [SCSI] don't build scsi_dma_{map,unmap} for !HAS_DMA
  [SCSI] Clean up scsi_add_lun a bit
  [SCSI] 53c700: Remove printk, which triggers because of low scsi clock on SNI RMs
  [SCSI] sni_53c710: Cleanup
  [SCSI] qla4xxx: Fix underrun/overrun conditions
  [SCSI] megaraid_mbox: use mutex instead of semaphore
  [SCSI] aacraid: add 51245, 51645 and 52245 adapters to documentation.
  [SCSI] qla2xxx: update version to 8.02.00-k1.
  [SCSI] qla2xxx: add support for NPIV
  [SCSI] stex: use resid for xfer len information
  [SCSI] Add Brownie 1200U3P to blacklist
  [SCSI] scsi.c: convert to use the data buffer accessors
  ...

Change Kconfig objects from "menu, config" into "menuconfig" so
that the user can disable the whole feature without having to
enter the menu first.

Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

iscsi_iser: convert to use the data buffer accessors

- remove the unnecessary map_single path.

- convert to use the new accessors for the sg lists and the
parameters.

TODO: use scsi_for_each_sg().

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

iSCSI must support software iscsi (iscsi_tcp, iser), hardware iscsi (qla4xxx),
and partial offload (broadcom). To be able to allow each stack or driver
or port (virtual or physical) to be able to log into the same target portal
we use the initiator tuple [[HWADDRESS | NETDEVNAME], INITIATOR_NAME] and
the target tuple [TARGETNAME, CONN_ADDRESS, CONN_PORT] to id a session.
This patch adds the netdev name, which is used by software iscsi when
it binds a session to a netdevice using the SO_BINDTODEVICE sock opt.
It cannot use HWADDRESS because if someone did vlans then the same netdevice
will have the same mac and the initiator,target id will not be unique.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Cc: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

This patch allows us to set can_queue and cmds_per_lun from userspace
when we create the session/host. From there we can set it on a per
target basis. The patch fully converts iscsi_tcp, but only hooks
up ib_iser for cmd_per_lun since it currently has a lots of preallocations
based on can_queue.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

The cmdsn allocation and pdu transmit code can race, and we can end
up sending a pdu with cmdsn 10 before a pdu with 5. The target will
then fail the connection/session. This patch fixes the problem by
delaying the cmdsn allocation until we are about to send the pdu.

This also removes the xmitmutex. We were using the connection xmitmutex
during error handling to handle races with mtask and ctask cleanup and
completion. For ctasks we now have nice refcounting and for the mtask,
if we hit the case where the mtask timesout and it is floating
around somewhere in the driver, we end up dropping the session.
And to handle session level cleanup, we use the xmit suspend bit
along with scsi_flush_queue and the session lock to make sure
that the xmit thread is not possibly transmitting a task while
we are trying to kill it.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

The attached patches add sysfs files for the chap settings
to the iscsi transport class, iscsi_tcp and ib_iser. This is
needed for software iscsi because there are times when iscsid
can die and it will need to reread the values it was using.
And it is needed by qla4xxx for basic management opertaions.
This patch does not hook in qla4xxx yet, because I am not sure
the mbx command to use.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>