Pull trivial tree updates from Jiri Kosina:
 "Usual rocket science stuff from trivial.git"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
  neighbour.h: fix comment
  sched: Fix warning on make htmldocs caused by wait.h
  slab: struct kmem_cache is protected by slab_mutex
  doc: Fix typo in USB Gadget Documentation
  of/Kconfig: Spelling s/one/once/
  mkregtable: Fix sscanf handling
  lp5523, lp8501: comment improvements
  thermal: rcar: comment spelling
  treewide: fix comments and printk msgs
  IXP4xx: remove '1 &&' from a condition check in ixp4xx_restart()
  Documentation: update /proc/uptime field description
  Documentation: Fix size parameter for snprintf
  arm: fix comment header and macro name
  asm-generic: uaccess: Spelling s/a ny/any/
  mtd: onenand: fix comment header
  doc: driver-model/platform.txt: fix a typo
  drivers: fix typo in DEVTMPFS_MOUNT Kconfig help text
  doc: Fix typo (acces_process_vm -> access_process_vm)
  treewide: Fix typos in printk
  drivers/gpu/drm/qxl/Kconfig: reformat the help text
  ...

Pull MFD changes from Lee Jones:
 "New drivers
   - Samsung Maxim 14577; Micro USB, Regulator, IRQ Controller and
     Battery Charger
   - TI/National Semiconductor LP3943 I2C GPIO Expander and PWM
     Generator

  Existing driver adaptions
   - Expansion of Wolfson Arizona DSP and High-Pass filter controls
   - TI TWL6040 default Regmap support and Regcache addition/bypass
   - Some nice Smatch catch fixes
   - Conversion of TI OMAP-USB and TI TWL6030 to endian neutralness
   - ChromeOS EC timing (delay) adaptions and added dependency on OF
   - Many constifications of 'struct {mfd_cell,regmap_irq,et.al}'
   - Watchdog support added for NVIDIA AS3722
   - Convert functions to static in TI AM335x
   - Realigned previously defeated functionality in TI AM335x
   - IIO ADC-TSC concurrency dead-lock/timeout resolution
   - Addition of Power Management and Clock support for Samsung core
   - DEFINE_PCI_DEVICE_TABLE macro removal from MFD Subsystem
   - Greater use of irqdomain functionality in ST-E AB8500
   - Removal of 'include/linux/mfd/abx500/ab8500-gpio.h'
   - Wolfson WM831x PMIC Power Management changes s/poweroff/shutdown/
   - Device Tree documentation added for TI/Nat Semi LP3943
   - Version detection and voltage tables for TI TPS6586x PMIC devices
   - Simplification of Freescale MC13XXX (de-)initialisation routines
   - Clean-up and simplification of the Realtek parent driver
   - Added support for RTL8402 Realtek PCI-Express card reader
   - Resource leak fix for Maxim 77686
   - Possible suspend BUG() fix in OMAP USB TLL
   - Support for new Wolfson WM5110 Revision (D)
   - Testing of automatic assignment of of_node in mfd_add_device()
   - Reversion of the above when it started to cause issues
   - Remove legacy Platform Data from;
              TI TWL Core, Qualcomm SSBI and ST-E ABx500 Pinctrl
   - Clean-ups; tabbing issues, function name changes, 'drvdata = NULL'
              removal, unused uninitialised warning mitigation, error
              message clarity, removal of redundant/duplicate checks,
              licensing (GPL -> GPL2), coding consistency, duplicate
              function declaration, ret checks, commit corrections,
              redundant of_match_ptr() helper removal, spelling,
              #if-deffery removal and header guards name changes"

* tag 'mfd-3.14-1' of git://git.linaro.org/people/ljones/mfd: (78 commits)
  mfd: wm5110: Add register patch for rev D chip
  mfd: omap-usb-tll: Don't hold lock during pm_runtime_get/put_sync()
  gpio: lp3943: Remove redundant of_match_ptr helper
  mfd: sta2x11-mfd: Use named constants for pci_power_t values
  Documentation: mfd: Fix LDO index in s2mps11.txt
  mfd: Cleanup mfd-mcp-sa11x0.h header
  mfd: max8997: Use "IS_ENABLED(CONFIG_OF)" for DT code.
  mfd: twl6030: Fix endianness problem in IRQ handler
  mfd: sec-core: Add cells for S5M8767-clocks
  mfd: max14577: Remove redundant of_match_ptr helper
  mfd: twl6040: Fix sparse non static symbol warning
  mfd: Revert "mfd: Always assign of_node in mfd_add_device()"
  mfd: rtsx: Fix sparse non static symbol warning
  mfd: max77693: Set proper maximum register for MUIC regmap
  mfd: max77686: Fix regmap resource leak on driver remove
  mfd: Represent correct filenames in file headers
  mfd: rtsx: Add support for card reader rtl8402
  mfd: rtsx: Add set pull control macro and simplify rtl8411
  mfd: max8997: Enforce mfd_add_devices() return value check
  mfd: mc13xxx: Simplify probe() & remove()
  ...

Immutable branch for IIO and Input

The ADC driver always programs all possible ADC values and discards
them except for the value IIO asked for. On the am335x-evm the driver
programs four values and it takes 500us to gather them. Reducing the number
of conversations down to the (required) one also reduces the busy loop down
to 125us.

This leads to another error, namely the FIFOCOUNT register is sometimes
(like one out of 10 attempts) not updated in time leading to EBUSY.
The next read has the FIFOCOUNT register updated.
Checking for the ADCSTAT register for being idle isn't a good choice either.
The problem is that if TSC is used at the same time, the HW completes the
conversation for ADC *and* before the driver noticed it, the HW begins to
perform a TSC conversation and so the driver never seen the HW idle. The
next time we would have two values in the FIFO but since the driver reads
everything we always see the current one.
So instead of polling for the IDLE bit in ADCStatus register, we should
check the FIFOCOUNT register. It should be one instead of zero because we
request one value.

This change in turn leads to another error. Sometimes if TSC & ADC are
used together the TSC starts generating interrupts even if nobody
actually touched the touchscreen. The interrupts seem valid because TSC's
FIFO is filled with values for each channel of the TSC. This condition stops
after a few ADC reads but will occur again. Not good.

On top of this (even without the changes I just mentioned) there is a ADC
& TSC lockup condition which was reported to me by Jeff Lance including the
following test case:
A busy loop of "cat /sys/bus/iio/devices/iio\:device0/in_voltage4_raw"
and a mug on touch screen. With this setup, the hardware will lockup after
something between 20 minutes and it could take up to a couple of hours.
During that lockup, the ADCSTAT register says 0x30 (or 0x70) which means
STEP_ID = IDLE and FSM_BUSY = yes. That means the hardware says that it is
idle and busy at the same time which is an invalid condition.

For all this reasons I decided to rework this TSC/ADC part and add a
handshake / synchronization here:
First the ADC signals that it needs the HW and writes a 0 mask into the
SE register. The HW (if active) will complete the current conversation
and become idle. The TSC driver will gather the values from the FIFO
(woken up by an interrupt) and won't "enable" another conversation.
Instead it will wake up the ADC driver which is already waiting. The ADC
driver will start "its" conversation and once it is done, it will
enable the TSC steps so the TSC will work again.

After this rework I haven't observed the lockup so far. Plus the busy
loop has been reduced from 500us to 125us.

The continues-read mode remains unchanged.

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The update of the SE register in MFD doesn't look right as it has
nothing to do with it. The better place to do it is in TSC driver (which
is already doing it) and in the ADC driver which needs this only in the
continues mode.

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The purpose of reg_se_cache has been defeated. It should avoid the
read-back of the register to avoid the latency and the fact that the
bits are reset to 0 after the individual conversation took place.

The reason why this is required like this to work, is that read-back of
the register removes the bits of the ADC so they do not start another
conversation after the register is re-written from the TSC side for the
update.
To avoid the not required read-back I introduce a "set once" variant which
does not update the cache mask. After the conversation completes, the
bit is removed from the SE register anyway and we don't plan a new
conversation "any time soon". The current set function is renamed to
set_cache to distinguish the two operations.
This is a small preparation for a larger sync-rework.

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

It somehow looks like the ending bracket belongs to the if statement but
it does belong to the while loop. This patch moves the bracket where it
belongs.

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add Capella Microsystem CM32181 Ambient Light Sensor IIO driver.
This driver will convert raw data to lux value under open-air
condition. Change the calibscale based on the cover material.

Signed-off-by: Kevin Tsai <ktsai@capellamicro.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Jonathan writes:

2nd round of new IIO drivers, features and cleanups for the 3.14 cycle.

New drivers

* HID inclinometer driver.

* DHT11 humidity driver.  Note that previous humidity drivers have been in
  hwmon, but no one was ever entirely happy with that, and they should find
  a more comfortable home in IIO (their original placement in hwmon was my
  fault - oops).  As this is our first humidity driver, core support is also
  added.

New features

* Two of mxs-lradc channels are internally wired to a temperature sensor,
  make this explicit in the driver by providing the relevant temperature
  channel.

* Add support for blocking IO on buffers.

* Add a data_available call back to the interface between buffer implementations
  and the core.  This is much cleaner than the old, 'stufftoread' flag.
  Implemented in the kfifo buffer.

Cleanups

* Last user of the old event configuration interface is converted and the
  old interface dropped.  Nice to be rid of this thanks to Lars-Peter's hard
  work!

* Replace all remaining instances of the IIO_ST macro with explicit filling
  of the scan_type structure within struct iio_chan_spec.  This macro was a
  bad idea, that rapidly ceased to cover all elements of the structure.
  Miss reading of the macro arguements has led to a number of bugs so lets
  just get rid of it. The final removal patch is awaiting for some fixes
  to make their way into mainline.
  In a couple of drivers, no elements of scan_type were even being used so
  in those case, it has been dropped entirely.

* Drop a couple of of_match_ptr helper uses in drivers where devicetree is
  not optional and hence the structures being protected by this always exist.

* Fix up some cases where data was read from a device in a particular
  byte order, but he code placed it into a s16 or similar.  These were
  highlighted by Sparse.

* Use the new ATTRIBUTE_GROUPS macro to drop some boiler plate in the triggers
  core code.

* ad7746 and ad7280a - stop storing buffers on the stack, giving cleaner code
  and possibly avoiding issues with i2c bus drivers that assume they can dma
  directly into the buffer.  Note that this cannot currently happen as the the
  i2c_smbus_read_i2c_block_data function has a memcpy from the buffer actually
  passed to the bus driver.  I missed this element of the commit message
  and don't think it is major enough to rebase the iio tree.

* ad5791 and ad5504 stop storing buffers on the stack for an SPI driver.
  Unlike the i2c drivers, this is a real issue for SPI drivers which can dma
  directly into the buffer supplied.

This resolves a merge issue with drivers/staging/imx-drm/imx-drm-core.c

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>