DHT11 isn't addressable and will trigger temperature measurement on any
data sent on the bus.

Signed-off-by: Kent Gustavsson <kent@minoris.se>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Jonathan writes:

First set of new device support, features and cleanups for IIO in the 5.6 cycle

New device support

* ad7091r5 ADC
  - New driver with follow up patch adding scale and vref support.
  - DT bindings
* ad7923
  - Support for ad7908, ad7918 and ad7928 added to driver.
* bma180
  - Support the BMA254 accelerometer. Required fairly substantial rework
    to allow for small differences between this an existing parts.
* bma400 accelerometer
  - New driver with follow up patch for regulator support.
  - DT bindings.
* asc dlhl60d
  - New driver support this range of pressure and temperature sensors.
  - DT bindings.
* ltc2496 ADC
  - New driver to support this ADC.
  - Split the existing LTC2497 driver generic component out and reuse.
  - DT bindings.
* parallax ping
  - New driver supporting ultrasonic and laser tof distance sensors.
  - Bindings for these sensors.

New features

* core
  - New char type for read_raw returns, used for thermocouple types.
  - Rename read_first_n callback to read.   The reasons behind the original
    naming are lost to the mists of time.
* ad799x
  - Allow pm_ops to disable device completely allowing regulator power down.
* bma180
  - Enable basic regulator support.
* dmaengine buffer
  - Report platform data alignment requirements via new ABI.
* max31856
  - Add option to set mains filter rejection frequency and document
    new in_temp_filter_notch_center_frequency ABI.
  - Add support for configuring HW averaging (oversampling ratio)
  - Add runtime configuration of thermocouple type and document new ABI.
* maxim-thermocouple
  - Add read only access to thermocouple type using new ABI, includes
    adding more specific compatibles to reflect which variant of the
    chip is being used.
* mpu6050
  - Provide option to support the PMU9150 in package magnetometer directly
    rather than via auxiliary bus.
* stm32_adc
  - Add overrun interrupt checks to detect if this happens.
* st_lsm6dsx
  - Enable the sensor-hub support for lsm6dsm. Includes various reworks to
    allow this.

Cleanups and minor fixes

* Subsystem wide
  - Tidy up indentation in Kconfig and fix alphabetical order of AD7091R5.
  - Drop linux/gpio.h and linux/of_gpio.h from drivers that don't use them.
* ad7266
  - Convert to GPIO descriptors.
* ad7303
  - Avoid a dance with checking if the regulator is supplied by just
    using the optional request interface.
* ad7887
  - Simplify channel specification assignment to enable adding more devices.
* ad7923
  - Drop some unused and largely pointless defines of BOB_N==N variety.
  - Tidy up checkpatch warnings.
  - Add missing of_device_id table.
* adf4350
  - Convert to GPIO descriptors.
* ak8975
  - Convert to GPIO descriptors.
* ADIS library and drivers
  - Expand scope of txrx_lock to cover all state and rename as state_lock
  - Add unlocked read / write to allow grouping of consecutive calls under
    single lock / unlock.
  - Add unlocked check_status, reset to allow grouping under single
    lock / unlock.
  - Remove remaining uses of core mlock for local state protection.
    mlock should never be used directly as it protects tightly defined
    core IIO device management state.
* adis16240
  - Enforce only supported SPI mode on driver load + add DT binding doc.
* atlas-ph-sensor
  - Rename to atlas-sensor given it now covers things beyond ph sensors.
* bma180
  - Use local dev variable to tidy up code.
  - Use c99 style explicity .member assignment to make driver more readable.
* bmp280
  - Drop ACPI support. No evidence this was used and appropriate ID is not
    registered.
  - Allow ACPI to bind device via PRP0001
* dmaengine buffer
  - Use dma_request_chan instead of dma_request_slave_channel_reason as that
    ABI is going away.
  - Add module info to avoid tainting the kernel.
* hts221
  - Avoid magic number defines when only used to fill structure elements
    that are self describing.
* lm3533
  - Drop a stray semicolon.
* max9611
  - Cleanup enum handling to be more resilient to future changes.
* mpu6050
  - Delete MPU9150 from supported SPI devices as doesn't provide SPI.
  - Select I2C_MUX again after kbuild issue fixed elsewhere.
* stm32-timer
  - Drop an unnecessary register update.
* ssp_sensors
  - Convert to GPIO descriptors.
* st_sensors
  - drop !CONFIG_ACPI defines as ACPI_PTR() will stop them being used
    anyway.
  - Make default platform data structures __maybe_unsued.
  - Fill in some missing kernel-doc function parameters.
* st_lsm6dsx
  - white space fixes.
  - Mark some constants that aren't always used as __maybe_unused.
  - Drop of ID table guards as they just pervent use under ACPI.
  - Switch to device properties to allow ACPI usage.
* st_uvis25
  - Drop acpi.h include as no ACPI APIs used.
* ti-ads1015
  - Drop legacy platform data as no one seems to be using it.
  - Use the device property API instead of OF specific.
* ti-ads7950
  - typo fix in error message.

* tag 'iio-for-5.6a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (99 commits)
  iio: accel: bma180: BMA254 support
  iio: pressure: bmp280: Allow device to be enumerated from ACPI
  iio: pressure: bmp280: Drop ACPI support
  dt-bindings: iio: adc: convert sd modulator to json-schema
  iio: buffer: rename 'read_first_n' callback to 'read'
  iio: buffer-dmaengine: Report buffer length requirements
  bindings: iio: pressure: Add documentation for dlh driver
  dt-bindings: Add asc vendor
  iio: pressure: Add driver for DLH pressure sensors
  iio: buffer-dmaengine: Add module information
  iio: accel: bma180: Use explicit member assignment
  iio: accel: bma180: Basic regulator support
  iio: accel: bma180: Add dev helper variable
  iio: imu: st_lsm6dsx: enable sensor-hub support for lsm6dsm
  iio: imu: st_lsm6dsx: rename st_lsm6dsx_shub_read_reg in st_lsm6dsx_shub_read_output
  iio: imu: st_lsm6dsx: check if shub_output reg is located in primary page
  iio: imu: st_lsm6dsx: check if pull_up is located in primary page
  iio: imu: st_lsm6dsx: check if master_enable is located in primary page
  iio: imu: st_lsm6dsx: export max num of slave devices in st_lsm6dsx_shub_settings
  iio: light: remove unneeded semicolon
  ...

Move some register definitions to hts221_avg_list, hts221_avg_list and
hts221_channels since they are used only there and simplify driver code

Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The IIO_HUMIDITYRELATIVE channel was being incorrectly reported back
as percent when it should have been milli percent. This is via an
incorrect scale value being returned to userspace.

Signed-off-by: Chris Lesiak <chris.lesiak@licor.com>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The iio_triggered_buffer_postenable() hook should be called first to
attach the poll function and the iio_triggered_buffer_predisable() hook
should be called last in the predisable hook.

This change updates the driver to attach/detach the poll func in the
correct order.

Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Use device-managed APIs to simplify the code.
The remove functions are redundant now and can
be deleted.

Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Pull staging and IIO driver updates from Greg KH:
 "Here is the big Staging and IIO driver update for 5.3-rc1.

  Lots of new IIO drivers are in here, along with loads of tiny staging
  driver cleanups and fixes. Overall we almost break even with the same
  lines added as removed.

  Full details are in the shortlog, they are too large to list here.

  All of these changes have been in linux-next for a while with no
  reported issues"

* tag 'staging-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (608 commits)
  staging: kpc2000: simplify comparison to NULL in fileops.c
  staging: kpc2000: simplify comparison to NULL in dma.c
  staging: kpc2000: simplify comparison to NULL in kpc2000_spi.c
  staging: rtl8723bs: hal: remove redundant assignment to packetType
  staging: rtl8723bs: Change return type of hal_btcoex_IsBtDisabled()
  staging: rtl8723bs: Remove rtw_btcoex_DisplayBtCoexInfo()
  staging: rtl8723bs: Remove function rtw_btcoex_GetDBG()
  staging: rtl8723bs: Remove function rtw_btcoex_SetDBG()
  staging: rtl8723bs: Remove rtw_btcoex_IsBTCoexCtrlAMPDUSize()
  staging: rtl8723bs: Remove rtw_btcoex_BtInfoNotify()
  staging: rtl8723bs: Remove rtw_btcoex_ScanNotify()
  staging: rtl8723bs: Remove rtw_btcoex_SetSingleAntPath()
  staging: rtl8723bs: Remove rtw_btcoex_SetPGAntNum()
  staging: rtl8192e: remove redundant initialization of rtstatus
  staging: rtl8723bs: Remove rtw_btcoex_GetRaMask()
  staging: rtl8723bs: Remove rtw_btcoex_SetChipType()
  staging: rtl8723bs: Remove rtw_btcoex_ConnectNotify()
  staging: rtl8723bs: Remove rtw_btcoex_SetBTCoexist()
  staging: rtl8723bs: Remove rtw_btcoex_IsBtDisabled()
  staging: rtl8723bs: Remove rtw_btcoex_IsBtControlLps()
  ...

so the hyper-v clocksource update can be applied.

Jonathan writes:

Second set of IIO device support, features, cleanups and minor fixes for 5.3.

A few bits for the counters subsystem mixed in here as well.
There are some late breaking fixes as well, which aren't so urgent
they can't wait for the merge window.

New Device Support
* adf4371
  - New driver + bindings.
  - Support the adf4372 PLL. Mostly ID and bindings.
* ad8366 (note includes rework of driver needed to allow support for these).
  - Support the ADL5240 variable gain amplifier (VGA).
  - Support the ADA4961 digital gain amplifier (DGA).
* dps310
  - New driver, in several parts from different authors for this temp
    and pressure sensor.
  - Includes errata workaround for a temperature reading issue.
* stk3310
  - Support the stk3335, mostly ID.

Features and cleanups
* core
  - drop error handling on debugfs registration.
  - harden by making sure we don't overrun iio_chan_info_postfix.
* docs
  - convert remaining docs to rst. At somepoint we'll fit these few
    into the main IIO docs.
  - improve sampling_frequency_available docs but explaining the
    range form.
* ad_sigma_delta
  - Drop a pointless goto.
* ad2s1210
  - Drop pointless platform data null check seeing as we don't actually
    use platform data anymore.
* ad7124
  - Relax limitation on channel numbers to allow pseudo different channels.
  - Support control of whether the input is buffered via DT.
  - Use dynamic allocation for channel configuration to make it easier
    to support new devices.
  - YAML binding conversion.
* ad7150
  - Comment tidy up.
  - Consistent and simple if (ret) handling of i2c errors.
  - FIELD_GET and GENMASK.
  - Ternary rather than !!(condition) for readability.
  - Use macros to avoid repetition of channel definitions.
* ad7606
  - Add software channel config (rather that pin controlled)
  - Refactor to simplify addition of new part in future.
* ad7746
  - of_deivce_id table.
* ad7780
  - MAINTAINERS entry
  - YAML DT bindings.
* ad8366
  - Stop using core mlock in favour of well scoped local lock.
  - SPDX + copyright date update.
* ad9834
  - of_device_id table
* adf4371
  - Add support for output stage muting before lock on has occured.
* adis library
  - MAINTAINERS entry to reflect that this now Alexandru's problem ;)
* adis162xx:
  - Fix a slightly incorrect set of comments and print statements on
    minimum supported voltage.
* adis16203
  - of_device_id table.
* adis16240
  - Add of_device_id table (in two parts as first patch only used it for
    MODULE_DEVICE_TABLE.)
* adt7316-spi
  - of_device_id table
* adxl372
  - YAML DT binding conversion.
  - Cleanup use of buffer callback functions (precursor to core rework).
* bh1710
  - Simplify getting the i2c adapter from the client.
* dht11
  - Mote to newer GPIO consumer interface.
* kxcjk-1013.c
  - Add binding for sensor in display of some ultrabooks after userspace
    tools updated for it not be a problem to report two similar sensors.
* imx7d
  - drop unused variables.
  - white space
  - define instead of variable for clock frequency that is fixed.
  - drop pointless error message.
* messon_saradc
  - SPDX
* sps30
  - MAINTAINERS entry
  - YAML binding conversion.
* st_accel
  - Tidy up ordering in various buffer related callbacks. This is
    part of a long running effort to simplify the core code.
* stm32-dfsdm:
  - Manage the resolution cleanly in triggerd modes.
  - Add fast mode support which allows more flexible filter choices.
  - Add a comment on the reason for a 16 bit record when technically
    not 'required'.
* st_lsm6dsx
  - Embed device name in the sensor_settings struct as i3c doesn't
    have a convenient name field to use for this.
* xilinx-adc
  - Relax constraints on supported platforms to reflect that this
    can used with FPGAs on PCIe cards and hence many architectures.
* counters/ftm-quaddec
  - Fix some formatting io MODULE_AUTHOR
  - MAINTAINERS entry

Fixes
* tools
  - fix incorrect handling of 32 bit channels.
* sca3000
  - Potential endian bug that is unlikely to bite anyone (be64 host
    seems unlikely for this old part).
* stm32-adc
  - Add vdda-supply. On some boards it needs to be turned on to supply
    the ADC.  DT bindings included.
* stm32-dfsdm
  - Fix output resolution to work with filter orders other than 3.
  - Fix output datatype as it's signed and previously claimed not to be.

* tag 'iio-for-5.3b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (68 commits)
  iio: iio-utils: Fix possible incorrect mask calculation
  iio: frequency: adf4371: Add support for output stage mute
  dt-bindings: iio: frequency: Add ADF4372 PLL documentation
  iio: frequency: adf4371: Add support for ADF4372 PLL
  dt-bindings: iio: adc: Add buffered input property
  Convert AD7124 bindings documentation to YAML format.
  iio: adc: ad7124: Shift to dynamic allocation for channel configuration
  iio: adc: ad7124: Add buffered input support
  iio: adc: ad7124: Remove input number limitation
  MAINTAINERS: add ADIS IMU driver library entry
  iio: adis162xx: fix low-power docs & reports
  counter/ftm-quaddec: Add missing '>' in MODULE_AUTHOR
  iio: core: no need to check return value of debugfs_create functions
  docs: iio: convert to ReST
  iio: adc: stm32-adc: add missing vdda-supply
  dt-bindings: iio: adc: stm32: add missing vdda supply
  iio: adc: stm32-dfsdm: add comment for 16 bits record
  iio: adc: stm32-dfsdm: add fast mode support
  iio: adc: stm32-dfsdm: manage data resolution in trigger mode
  iio: adc: stm32-dfsdm: fix data type
  ...

This makes boot uniformly boottime and tai uniformly clocktai, to
address the remaining oversights.

Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lkml.kernel.org/r/20190621203249.3909-2-Jason@zx2c4.com