This is IDE host driver for AT91 (SAM9, CAP9, AT572D940HF) Static Memory
Controller with Compact Flash True IDE Mode logic.

Driver have to switch 8/16 bit bus width when accessing Task Tile or Data
Register. Moreover some extra things need to be done when setting PIO mode.
Only PIO mode is used, hardware have no DMA support. If interrupt line is
connected through GPIO extra quirk is needed to cope with fake interrupts.

Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Cc: Andrew Victor <avictor.za@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Documentation/kernel-parameters.txt
- ide=nodma is no longer valid.

drivers/ide/Kconfig
- The module is ide-core.ko not ide.

drivers/ide/ide.c
- It took me a while to figure out what the arguments %d.%d:%d to nodma
  module parameter ment, so I added a comment to each.
- Added a comment to each of the sscanf lines.
- There is a bug, if j is 0 it would previously clear all the other bits
  except the current device, changed in three different places.
  mask &= (1 << i) should be mask &= ~(1 << i).

Signed-off-by: David Fries <david@fries.net>
[bart: s/disk/device/ in ide.c, beautify patch description]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

This is a port of libata's pata_cs5536.c (written by Martin K. Petersen)
to IDE subsystem.

Changes done while at it:

* Reprogram PIO/MWDMA timings if needed before and after DMA transfer
  (chipset uses shared PIO/MWDMA timings).

* Fix cable detection to report 80-wires cable if BIOS set it for any
  device on a port (IDE core will do drive-side cable detection later).

* Don't disable UDMA while programming PIO timings.

* Simplify PCI/MSR support.

Pros of having IDE host driver in addition to libata's one:

* IDE is much lighter than SCSI+libata, the host driver itself is also
  a bit smaller:

   text    data     bss     dec     hex filename
   1261     496       4    1761     6e1 drivers/ata/pata_cs5536.o
   1242     128       4    1374     55e drivers/ide/cs5536.o

* This allows use of IDE features which are unavailable under libata.

v2:
* Fixes per review from Sergei:
  - simplify dependency check in Kconfig
  - use IDE_DRV_MASK also for ->drive_data
  - disable UDMA when programming MWDMA
  - program new DTC timings only when necessary
  - fix printk() level in cs5536_init_one()

* Fix patch description according to comments from Alan and Sergei.

v3:
* Smarter masking of UDMA bits per Sergei's suggestion.

Cc: Martin K. Petersen <mkp@mkp.net>
Cc: Karl Auerbach <karl@iwl.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Support for the IT8172 IDE controller was removed from the kernel
sometime after 2.6.18.  Support for the only boards that used the IT8172
was removed from the kernel after 2.6.18, as they had never compiled
since 2.6.0.  However, there are a couple of platforms that use this
chip: the PMC-Sierra Xiao Hu thin-client computer, which is no longer
in production, and the Linksys NSS4000 Network Attached Storage box,
which is based on the Xiao Hu board.  I am attempting to add support
for the Xiao Hu to the kernel, and this IT8172 IDE controller is the
first bit of code in this effort.

This patch resurrects the IT8172 IDE controller code.  I began with
the 2.6.18 version of the it8172.c file, and have moved it forward so
that it works with the latest version of the kernel.  I have run this
driver on a PMC-Sierra Xiao Hu board with the 2.6.28 kernel, and
I have had no problems with it in my configuration.  The attached patch
applies cleanly against 2.6.28.

Signed-off-by: Shane McDonald <mcdonald.shane@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: alan@lxorguk.ukuu.org.uk
[bart: s/HWIF(drive)/drive->hwif/]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

... by factoring it out of ide_cd_do_request() into a helper, as suggested by
Bart.

There should be no functionality change resulting from this patch.

Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
[bart: BLK_DEV_IDECD needs to select IDE_ATAPI now]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

As planed, this removes ide-scsi.

The 2.6 kernel supports direct writing to ide CD drives, which
eliminates the need for ide-scsi. ide-scsi has been unmaintained and
marked as deprecated.

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James.Bottomley@HansenPartnership.com
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (407 commits)
  [ARM] pxafb: add support for overlay1 and overlay2 as framebuffer devices
  [ARM] pxafb: cleanup of the timing checking code
  [ARM] pxafb: cleanup of the color format manipulation code
  [ARM] pxafb: add palette format support for LCCR4_PAL_FOR_3
  [ARM] pxafb: add support for FBIOPAN_DISPLAY by dma braching
  [ARM] pxafb: allow pxafb_set_par() to start from arbitrary yoffset
  [ARM] pxafb: allow video memory size to be configurable
  [ARM] pxa: add document on the MFP design and how to use it
  [ARM] sa1100_wdt: don't assume CLOCK_TICK_RATE to be a constant
  [ARM] rtc-sa1100: don't assume CLOCK_TICK_RATE to be a constant
  [ARM] pxa/tavorevb: update board support (smartpanel LCD + keypad)
  [ARM] pxa: Update eseries defconfig
  [ARM] 5352/1: add w90p910-plat config file
  [ARM] s3c: S3C options should depend on PLAT_S3C
  [ARM] mv78xx0: implement GPIO and GPIO interrupt support
  [ARM] Kirkwood: implement GPIO and GPIO interrupt support
  [ARM] Orion: share GPIO IRQ handling code
  [ARM] Orion: share GPIO handling code
  [ARM] s3c: define __io using the typesafe version
  [ARM] S3C64XX: Ensure CPU_V6 is selected
  ...

* Move legacy ISA/VLB ports handling from ide-probe.c to ide-legacy.c.

* Add CONFIG_IDE_LEGACY config option to be selected by host drivers
  needing ide-legacy.c.

v2:
Fix CONFIG_IDE_LEGACY not being defined in Kconfig.
(from Takashi Iwai <tiwai@suse.de>)

There should be no functional changes caused by this patch.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>