linux.git/drivers/i2c, branch v5.9-rc2

Merge tag 'acpi-5.9-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm

2020-08-15T15:18:22+00:00

Pull more ACPI updates from Rafael Wysocki:
 "Add new hardware support to the ACPI driver for AMD SoCs, the x86 clk
  driver and the Designware i2c driver (changes from Akshu Agrawal and
  Pu Wen)"

* tag 'acpi-5.9-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  clk: x86: Support RV architecture
  ACPI: APD: Add a fmw property is_raven
  clk: x86: Change name from ST to FCH
  ACPI: APD: Change name from ST to FCH
  i2c: designware: Add device HID for Hygon I2C controller

Merge branch 'i2c/for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux

2020-08-14T01:41:00+00:00

Pull i2c updates from Wolfram Sang:

 - bus recovery can now be given a pinctrl handle and the I2C core will
   do all the steps to switch to/from GPIO which can save quite some
   boilerplate code from drivers

 - "fallthrough" conversion

 - driver updates, mostly ID additions

* 'i2c/for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (32 commits)
  i2c: iproc: fix race between client unreg and isr
  i2c: eg20t: use generic power management
  i2c: eg20t: Drop PCI wakeup calls from .suspend/.resume
  i2c: mediatek: Fix i2c_spec_values description
  i2c: mediatek: Add i2c compatible for MediaTek MT8192
  dt-bindings: i2c: update bindings for MT8192 SoC
  i2c: mediatek: Add access to more than 8GB dram in i2c driver
  i2c: mediatek: Add apdma sync in i2c driver
  i2c: i801: Add support for Intel Tiger Lake PCH-H
  i2c: i801: Add support for Intel Emmitsburg PCH
  i2c: bcm2835: Replace HTTP links with HTTPS ones
  Documentation: i2c: dev: 'block process call' is supported
  i2c: at91: Move to generic GPIO bus recovery
  i2c: core: treat EPROBE_DEFER when acquiring SCL/SDA GPIOs
  i2c: core: add generic I2C GPIO recovery
  dt-bindings: i2c: add generic properties for GPIO bus recovery
  i2c: rcar: avoid race when unregistering slave
  i2c: tegra: Avoid tegra_i2c_init_dma() for Tegra210 vi i2c
  i2c: tegra: Fix runtime resume to re-init VI I2C
  i2c: tegra: Fix the error path in tegra_i2c_runtime_resume
  ...

i2c: iproc: fix race between client unreg and isr

2020-08-12T20:03:58+00:00

When i2c client unregisters, synchronize irq before setting
iproc_i2c->slave to NULL.

(1) disable_irq()
(2) Mask event enable bits in control reg
(3) Erase slave address (avoid further writes to rx fifo)
(4) Flush tx and rx FIFOs
(5) Clear pending event (interrupt) bits in status reg
(6) enable_irq()
(7) Set client pointer to NULL

Unable to handle kernel NULL pointer dereference at virtual address 0000000000000318

[  371.020421] pc : bcm_iproc_i2c_isr+0x530/0x11f0
[  371.025098] lr : __handle_irq_event_percpu+0x6c/0x170
[  371.030309] sp : ffff800010003e40
[  371.033727] x29: ffff800010003e40 x28: 0000000000000060
[  371.039206] x27: ffff800010ca9de0 x26: ffff800010f895df
[  371.044686] x25: ffff800010f18888 x24: ffff0008f7ff3600
[  371.050165] x23: 0000000000000003 x22: 0000000001600000
[  371.055645] x21: ffff800010f18888 x20: 0000000001600000
[  371.061124] x19: ffff0008f726f080 x18: 0000000000000000
[  371.066603] x17: 0000000000000000 x16: 0000000000000000
[  371.072082] x15: 0000000000000000 x14: 0000000000000000
[  371.077561] x13: 0000000000000000 x12: 0000000000000001
[  371.083040] x11: 0000000000000000 x10: 0000000000000040
[  371.088519] x9 : ffff800010f317c8 x8 : ffff800010f317c0
[  371.093999] x7 : ffff0008f805b3b0 x6 : 0000000000000000
[  371.099478] x5 : ffff0008f7ff36a4 x4 : ffff8008ee43d000
[  371.104957] x3 : 0000000000000000 x2 : ffff8000107d64c0
[  371.110436] x1 : 00000000c00000af x0 : 0000000000000000

[  371.115916] Call trace:
[  371.118439]  bcm_iproc_i2c_isr+0x530/0x11f0
[  371.122754]  __handle_irq_event_percpu+0x6c/0x170
[  371.127606]  handle_irq_event_percpu+0x34/0x88
[  371.132189]  handle_irq_event+0x40/0x120
[  371.136234]  handle_fasteoi_irq+0xcc/0x1a0
[  371.140459]  generic_handle_irq+0x24/0x38
[  371.144594]  __handle_domain_irq+0x60/0xb8
[  371.148820]  gic_handle_irq+0xc0/0x158
[  371.152687]  el1_irq+0xb8/0x140
[  371.155927]  arch_cpu_idle+0x10/0x18
[  371.159615]  do_idle+0x204/0x290
[  371.162943]  cpu_startup_entry+0x24/0x60
[  371.166990]  rest_init+0xb0/0xbc
[  371.170322]  arch_call_rest_init+0xc/0x14
[  371.174458]  start_kernel+0x404/0x430

Fixes: c245d94ed106 ("i2c: iproc: Add multi byte read-write support for slave mode")

Signed-off-by: Dhananjay Phadke 
Reviewed-by: Florian Fainelli 
Acked-by: Ray Jui 
Signed-off-by: Wolfram Sang

i2c: eg20t: use generic power management

2020-08-10T13:47:38+00:00

Drivers using legacy power management .suspen()/.resume() callbacks
have to manage PCI states and device's PM states themselves. They also
need to take care of standard configuration registers.

Switch to generic power management framework using a single
"struct dev_pm_ops" variable to take the unnecessary load from the driver.
This also avoids the need for the driver to directly call most of the PCI
helper functions and device power state control functions, as through
the generic framework PCI Core takes care of the necessary operations,
and drivers are required to do only device-specific jobs.

Signed-off-by: Vaibhav Gupta 
Reviewed-by: Bjorn Helgaas 
Signed-off-by: Wolfram Sang

i2c: eg20t: Drop PCI wakeup calls from .suspend/.resume

2020-08-10T13:46:31+00:00

The driver calls pci_enable_wake(...., false) in pch_i2c_suspend() as well
as pch_i2c_resume(). Either it should enable-wake the device in .suspend()
or should not invoke pci_enable_wake() at all.

Concluding that this driver doesn't support enable-wake and PCI core calls
pci_enable_wake(pci_dev, PCI_D0, false) during resume, drop it from
.suspend() and .resume().

Reported-by: Bjorn Helgaas 
Signed-off-by: Vaibhav Gupta 
Reviewed-by: Bjorn Helgaas 
Signed-off-by: Wolfram Sang

i2c: mediatek: Fix i2c_spec_values description

2020-08-10T09:39:35+00:00

The struct i2c_spec_values have it's members documented but is
missing the starting '@', which leads to warings like:

drivers/i2c/busses/i2c-mt65xx.c:267: warning: Function parameter or member 'min_low_ns' not described in 'i2c_spec_values'

We also delete min_high_ns member as it is not used in the code.

Signed-off-by: Matthias Brugger 
Reviewed-by: Qii Wang 
Signed-off-by: Wolfram Sang

i2c: designware: Add device HID for Hygon I2C controller

2020-08-07T18:07:44+00:00

Add device HID HYGO0010 to match the Hygon ACPI Vendor ID (HYGO) that
was registered in http://www.uefi.org/acpi_id_list, and the I2C
controller on Hygon paltform will use the HID.

Signed-off-by: Pu Wen 
Acked-by: Andy Shevchenko 
Acked-by: Wolfram Sang 
Signed-off-by: Rafael J. Wysocki

i2c: mediatek: Add i2c compatible for MediaTek MT8192

2020-08-05T21:40:49+00:00

Add i2c compatible for MT8192. Compare to MT8183 i2c controller,
MT8192 support more then 8GB DMA mode.

Signed-off-by: Qii Wang 
Signed-off-by: Wolfram Sang

i2c: mediatek: Add access to more than 8GB dram in i2c driver

2020-08-05T21:39:26+00:00

Newer MTK chip support more than 8GB of dram. Replace support_33bits
with more general dma_max_support and remove mtk_i2c_set_4g_mode.

Reviewed-by: Yingjoe Chen 
Signed-off-by: Qii Wang 
Signed-off-by: Wolfram Sang

i2c: mediatek: Add apdma sync in i2c driver

2020-08-05T21:39:08+00:00

With the apdma remove hand-shake signal, it need to keep i2c and
apdma in sync manually.

Reviewed-by: Yingjoe Chen 
Reviewed-by: Matthias Brugger 
Signed-off-by: Qii Wang 
Signed-off-by: Wolfram Sang