Mark (and unmark) device nodes with the POPULATE flag as appropriate.
This is required to avoid multi probing when using I2C and device
overlays containing a mux.
This patch is also more careful with the release of the adapter device
which caused a deadlock with muxes, and does not break the build
on !OF since the node flag accessors are not defined then.

Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Current code returns 0 if fails to read clock-frequency DT property,
fix it. Also add checking return value of clk_prepare_enable and
propagate return value of devm_request_irq.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Free requested mailbox channel before return error.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

If NO_DMA=y:

    ERROR: "dma_unmap_single" [drivers/i2c/busses/i2c-mt65xx.ko] undefined!
    ERROR: "dma_mapping_error" [drivers/i2c/busses/i2c-mt65xx.ko] undefined!
    ERROR: "dma_map_single" [drivers/i2c/busses/i2c-mt65xx.ko] undefined!

Add a dependency on HAS_DMA to fix this.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Pull char/misc driver updates from Greg KH:
 "Here's the big char/misc driver pull request for 4.2-rc1.

  Lots of mei, extcon, coresight, uio, mic, and other driver updates in
  here.  Full details in the shortlog.  All of these have been in
  linux-next for some time with no reported problems"

* tag 'char-misc-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (176 commits)
  mei: me: wait for power gating exit confirmation
  mei: reset flow control on the last client disconnection
  MAINTAINERS: mei: add mei_cl_bus.h to maintained file list
  misc: sram: sort and clean up included headers
  misc: sram: move reserved block logic out of probe function
  misc: sram: add private struct device and virt_base members
  misc: sram: report correct SRAM pool size
  misc: sram: bump error message level on unclean driver unbinding
  misc: sram: fix device node reference leak on error
  misc: sram: fix enabled clock leak on error path
  misc: mic: Fix reported static checker warning
  misc: mic: Fix randconfig build error by including errno.h
  uio: pruss: Drop depends on ARCH_DAVINCI_DA850 from config
  uio: pruss: Add CONFIG_HAS_IOMEM dependence
  uio: pruss: Include <linux/sizes.h>
  extcon: Redefine the unique id of supported external connectors without 'enum extcon' type
  char:xilinx_hwicap:buffer_icap - change 1/0 to true/false for bool type variable in function buffer_icap_set_configuration().
  Drivers: hv: vmbus: Allocate ring buffer memory in NUMA aware fashion
  parport: check exclusive access before register
  w1: use correct lock on error in w1_seq_show()
  ...

Pull i2c updates from Wolfram Sang:
 "Highlights:

   - new drivers for Mediatek I2C, APM X-Gene, Broadcom Settop
   - major updates to at91, davinci
   - bugfixes to the mux infrastructure when dealing with the new quirk
     mechanism
   - more users for the bus recovery feature
   - further improvements to the slave framework

  Plus the usual bunch of smaller driver and core improvements and
  fixes.

  There is one patch removing old code from an ARM platform.  This has
  been acked by the sh_mobile maintainer Simon Horman"

* 'i2c/for-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (48 commits)
  i2c: busses: i2c-bcm2835: limits cdiv to allowed values
  i2c: sh_mobile: use proper type for timeout
  i2c: sh_mobile: use adapter default for timeout
  i2c: rcar: use proper type for timeout
  i2c: rcar: use adapter default for timeout
  i2c: designware: Make sure the device is suspended before disabling runtime PM
  i2c: tegra: apply size limit quirk
  i2c: tegra: don't advertise SMBUS_QUICK
  i2c: octeon: remove unused signal handling
  i2c: davinci: Optimize SCL generation
  i2c: mux: pca954x: Use __i2c_transfer because of quirks
  i2c: mux: Use __i2c_transfer() instead of calling parent's master_xfer()
  i2c: use parent adapter quirks in mux
  i2c: bcm2835: clear reserved bits in S-Register
  ARM: shmobile: r8a7740: remove I2C errata handling
  i2c: sh_mobile: add errata workaround
  i2c: at91: fix code checker warnings
  i2c: busses: xgene-slimpro: fix incorrect __init declation for probe
  i2c: davinci: Avoid sending to own address
  i2c: davinci: Refactor i2c_davinci_wait_bus_not_busy()
  ...

Pull MFD updates from Lee Jones:
 "Changes to existing drivers:
   - Constify structures; throughout the subsystem
   - Move support to DT in; cros_ec
   - DT changes and documentation; cros-ec, max77693, max77686, arizona, da9063
   - ACPI changes and documentation; mfd-core
   - Use different platform specific API in; cros_ec_*, arizona-core
   - Remove unused parent field from; cros_ec_i2c
   - Add wake-up/reset delay in; cross_ec_spi, arizona-core
   - Staticise structures/functions in; cros_ec
   - Remove redundant code; arizona-core, max77686
   - Bugfix; twl4030-power
   - Allow compile test; aat2870, tps65910
   - MAINTAINERS adaptions; samsung, syscon
   - Resource Management (devm_*); arizona-core
   - Refactor Reset code; arizona-core
   - Insist on at least one full boot; arizona-core
   - Trivial formatting; arizona-core
   - Add low-power-sleep; arizona-core
   - IRQ ONESHOT changes; twl4030-irq, mc13xxx-core, wm831x-auxadc, htc-i2cpld,
                          wm8350-core, ab8500-debugfs, ab8500-gpadc, si476x-i2c

  (Re-)moved drivers:
   - Move protocol helpers out to drivers/platform; cros_ec

  New drivers/supported devices:
   - Add support for AXP22x into axp20x
   - Add support for OnKey into da9063-core
   - Add support for Pinctrl into mt6397-core
   - New STMicroelectronics LPC Watchdog driver
   - New STMicroelectronics LPC Real-Time Clock driver"

* tag 'mfd-for-linus-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (59 commits)
  mfd: lpc_ich: Assign subdevice ids automatically
  mfd: si476x-i2c: Pass the IRQF_ONESHOT flag
  mfd: ab8500-gpadc: Pass the IRQF_ONESHOT flag
  mfd: ab8500-debugfs: Pass the IRQF_ONESHOT flag
  mfd: wm8350-core: Pass the IRQF_ONESHOT flag
  mfd: htc-i2cpld: Pass the IRQF_ONESHOT flag
  mfd: wm831x-auxadc: Pass the IRQF_ONESHOT flag
  mfd: mc13xxx-core: Pass the IRQF_ONESHOT flag
  mfd: twl4030-irq: Pass the IRQF_ONESHOT flag
  mfd: mt6397-core: Add GPIO sub-module support
  mfd: arizona: Add convience defines for micd_rate/micd_bias_starttime
  mfd: dt: Add bindings for DA9063 OnKey
  mfd: da9063: Add support for OnKey driver
  mfd: arizona: Fix incorrect Makefile conditionals
  mfd: arizona: Add stub for wm5102_patch()
  mfd: Check ACPI device companion before checking resources
  Documentation: Add WM8998/WM1814 device tree bindings
  mfd: arizona: Split INx_MODE into two fields
  mfd: wm5110: Add delay before releasing reset line
  mfd: arizona: Add better support for system suspend
  ...

Pull MMC updates from Ulf Hansson:
 "Here are the changes for MMC for v4.2.

  MMC core:
   - Fix an error path in the mmc block layer
   - Fix PM domain attachment for the SDIO bus
   - Add support for driver strength selection
   - Increase a delay to let voltage stabilize
   - Add support for disabling write-protect detection
   - Add facility to support re-tuning
   - Re-tune and retry in the recovery path
   - Add reset option for SDIO
   - Consolidations and clean-ups

  MMC host:
   - Add Mediatek MMC driver
   - Constify platform_device_id for a couple of hosts
   - Fix modalias to make module auto-loading work for a couple of hosts
   - sdhci: Add support for sdhci-arasan4.9a
   - sdhci: Fix low memory corruption
   - sdhci: Restore behavior while creating OCR mask
   - sdhci: Add a callback to select drive strength
   - sdhci: Fix driver type B and D handling
   - sdhci: Add support for drive strength selection for SPT
   - sdhci: Enable HS400 for some Intel host controllers
   - sdhci: Convert to use the new re-tuning facility
   - sdhci: Various minor fixes and clean-ups
   - dw_mmc: Add support for hi6220
   - dw_mmc: Use core to handle absent write protect line
   - dw_mmc: Add support to switch voltage
   - tmio: Some fixes and modernizations
   - sh_mmcif: Improve clock rate calculation"

* tag 'mmc-v4.2' of git://git.linaro.org/people/ulf.hansson/mmc: (98 commits)
  mmc: queue: prevent soft lockups on PREEMPT=n
  mmc: mediatek: Add PM support for MMC driver
  mmc: mediatek: Add Mediatek MMC driver
  mmc: dt-bindings: add Mediatek MMC bindings
  mmc: card: Fixup request missing in mmc_blk_issue_rw_rq
  mmc: sdhci: fix low memory corruption
  mmc: sdhci-pci: Change AMD SDHCI quirk application scope
  i2c-piix4: Use Macro for AMD CZ SMBus device ID
  pci_ids: Add AMD KERNCZ device ID support
  mmc: queue: use swap() in mmc_queue_thread()
  mmc: dw_mmc: insmod followed by rmmod will hung for eMMC
  mmc: sdhci: Restore behavior while creating OCR mask
  mmc: sdhci-pxav3: fix device wakeup initialization
  mmc: core: Attach PM domain prior probing of SDIO func driver
  mmc: core: Remove redundant ->power_restore() callback for SD
  mmc: core: Remove redundant ->power_restore() callback for MMC
  mmc: sdhci-bcm2835: Actually enable the clock
  mmc: sdhci-bcm2835: Clean up platform allocations if sdhci init fails.
  mmc: sdhci-of-esdhc: enable interrupt mode to detect card
  mmc: sdhci-esdhc-imx: add quirk SDHCI_QUIRK2_BROKEN_HS200 for imx6qdl
  ...

Pull gpio updates from Linus Walleij:
 "This is the big bulk of GPIO changes queued for the v4.2 kernel
  series:

   - a big set of cleanups to the aged sysfs interface from Johan
     Hovold.  To get these in, v4.1-rc3 was merged into the tree as the
     first patch in that series had to go into stable.  This makes the
     locking much more fine-grained (get rid of the "big GPIO lock(s)"
     and store states in the GPIO descriptors.

   - rename gpiod_[g|s]et_array() to gpiod_[g|s]et_array_value() to
     avoid confusions.

   - New drivers for:
      * NXP LPC18xx (currently LPC1850)
      * NetLogic XLP
      * Broadcom STB SoC's
      * Axis ETRAXFS
      * Zynq Ultrascale+ (subdriver)

   - ACPI:
      * make it possible to retrieve GpioInt resources from a GPIO
        device using acpi_dev_gpio_irq_get()
      * merge some dependent I2C changes exploiting this.
      * support the ARM X-Gene GPIO standby driver.

   - make it possible for the generic GPIO driver to read back the value
     set registers to reflect current status.

   - loads of OMAP IRQ handling fixes.

   - incremental improvements to Kona, max732x, OMAP, MXC, RCAR,
     PCA953x, STP-XWAY, PCF857x, Crystalcove, TB10x.

   - janitorial (constification, checkpatch cleanups)"

* tag 'gpio-v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (71 commits)
  gpio: Fix checkpatch.pl issues
  gpio: pcf857x: handle only enabled irqs
  gpio / ACPI: Return -EPROBE_DEFER if the gpiochip was not found
  GPIO / ACPI: export acpi_gpiochip_request(free)_interrupts for module use
  gpio: improve error reporting on own descriptors
  gpio: promote own request failure to pr_err()
  gpio: Added support to Zynq Ultrascale+ MPSoC
  gpio: add ETRAXFS GPIO driver
  fix documentation after renaming gpiod_set_array to gpiod_set_array_value
  gpio: Add GPIO support for Broadcom STB SoCs
  gpio: xgene: add ACPI support for APM X-Gene GPIO standby driver
  gpio: tb10x: Drop unneeded free_irq() call
  gpio: crystalcove: set IRQCHIP_SKIP_SET_WAKE for the irqchip
  gpio: stp-xway: Use the of_property_read_u32 helper
  gpio: pcf857x: Check for irq_set_irq_wake() failures
  gpio-stp-xway: Fix enabling the highest bit of the PHY LEDs
  gpio: Prevent an integer overflow in the pca953x driver
  gpio: omap: rework omap_gpio_irq_startup to handle current pin state properly
  gpio: omap: rework omap_gpio_request to touch only gpio specific registers
  gpio: omap: rework omap_x_irq_shutdown to touch only irqs specific registers
  ...

Checks if the cdiv value is in between min (0x2) and max (0xFFFE)
supported values by the bcm2835. If not, it returns -ENODEV.

See page 33/34 of BCM2835-ARM-Peripherals.pdf for the DIV register.
https://www.raspberrypi.org/wp-content/uploads/2012/02/BCM2835-ARM-Peripherals.pdf

Signed-off-by: Silvan Wicki <linux_wi@tinag.ch>
[wsa: resolved a merge conflict]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>