linux.git/drivers/hid/Makefile, branch vsnprintf

Merge branch 'for-6.13/corsair' into for-linus

2024-11-18T20:58:24+00:00

- support for Corsair Void headset family (Stuart Hayhurst)

HID: Kysona: Add basic battery reporting for Kysona M600

2024-10-18T10:28:40+00:00

In this initial the battery is only probed once, a following patch will add
periodic checking.

Signed-off-by: Lode Willems 
Signed-off-by: Jiri Kosina

HID: corsair-void: Add Corsair Void headset family driver

2024-10-11T10:57:48+00:00

Introduce a driver for the Corsair Void family of headsets, supporting:
 - Battery reporting (power_supply)
 - Sidetone setting support
 - Physical microphone location reporting
 - Headset and receiver firmware version reporting
 - Built-in alert triggering
 - USB wireless_status

Tested with a Void Pro Wireless, Void Elite Wireless and a Void Elite Wired

Signed-off-by: Stuart Hayhurst 
Signed-off-by: Jiri Kosina

HID: hid-goodix: Add Goodix HID-over-SPI driver

2024-08-19T19:14:39+00:00

This patch introduces a new driver to support the Goodix GT7986U
touch controller. This device is not compatible with Microsoft's
HID-over-SPI protocol and therefore needs to implement its own
flavor. The data reported is packaged according to the HID
protocol but uses SPI for communication to improve speed. This
enables the device to transmit not only coordinate data but also
corresponding raw data that can be accessed by user-space programs
through the hidraw interface. The raw data can be utilized for
functions like palm rejection, thereby improving the touch experience.

Key features:
- Device connection confirmation and initialization
- IRQ-based event reporting to the input subsystem
- Support for HIDRAW operations (GET_REPORT and SET_REPORT)

Reviewed-by: Dmitry Torokhov 
Signed-off-by: Charles Wang 
Signed-off-by: Jiri Kosina

HID: uclogic: Avoid linking common code into multiple modules

2024-06-19T14:33:10+00:00

The hid-uclogic-params.o and hid-uclogic-rdesc.o files are linked
into both the driver module and the unit test, which triggers a
W=1 warning:

scripts/Makefile.build:236: drivers/hid/Makefile: hid-uclogic-rdesc.o is added to multiple modules: hid-uclogic hid-uclogic-test
scripts/Makefile.build:236: drivers/hid/Makefile: hid-uclogic-params.o is added to multiple modules: hid-uclogic hid-uclogic-test

Avoids this by moving these two files into a separate module
that is used by the driver and the unit test.

Reported-by: Arnd Bergmann 
Acked-by: Arnd Bergmann 
Signed-off-by: José Expósito 
Signed-off-by: Jiri Kosina

HID: Add WinWing Orion2 throttle support

2024-04-03T11:35:44+00:00

WinWing Orion2 throttle works with Linux out of box,
but the kernel sees only 16 of 47 buttons on the throttle base.

This module enables all buttons, and also adds LED controls.

Button numbers 0 .. 63 on Orion2 are reserved for throttle grip;
the throttle base buttons have numbers 64 .. 110.

Linux kernel HID subsystem only supports up to 80 buttons.

Remap throttle base buttons to numbers 32 .. 78,
reserving only numbers 0 .. 31 for buttons on the grip handle.

Changes since v2:
   - Fixed automatic line wraps added by mail client

Changes since v1:
   - Fixed formatting of descriptor byte array;
   - Using product codes of Winwing grips in config.

Signed-off-by: Ivan Gorinov 
Signed-off-by: Jiri Kosina

HID: mcp2200: added driver for GPIOs of MCP2200

2023-11-21T08:27:18+00:00

Added a gpiochip compatible driver to control the 8 GPIOs of
the MCP2200 by using the HID interface.

Using GPIOs with alternative functions (GP0<->SSPND, GP1<->USBCFG,
GP6<->RXLED, GP7<->TXLED) will reset the functions, if set (unset by
default).

The driver was tested while also using the UART of the chip. Setting
and reading the GPIOs has no effect on the UART communication. However,
a reset is triggered after the CONFIGURE command. If the GPIO Direction
is constantly changed, this will affect the communication at low baud
rates. This is a hardware problem of the MCP2200 and is not caused by
the driver.

Signed-off-by: Johannes Roith 
Reviewed-by: Rahul Rameshbabu 
Signed-off-by: Jiri Kosina

HID: hid-google-stadiaff: add support for Stadia force feedback

2023-08-14T09:35:37+00:00

Add a hid-google-stadiaff module to support rumble based force feedback
on the Google Stadia controller. This works using the HID output
endpoint exposed on both the USB and BLE interface.

Signed-off-by: Fabio Baltieri 
Reviewed-by: Rahul Rameshbabu 
Signed-off-by: Jiri Kosina

HID: nvidia-shield: Initial driver implementation with Thunderstrike support

2023-06-09T15:45:31+00:00

Supports the Thunderstrike (SHIELD 2017) controller. Implements support for
the Thunderstrike HOSTCMD firmware interface. Adds sysfs attributes about a
SHIELD device and introduces haptics support for controllers.

Signed-off-by: Rahul Rameshbabu 
Signed-off-by: Jiri Kosina

Merge branch 'for-6.3/hid-bpf' into for-linus

2023-02-22T09:44:31+00:00

Initial support of HID-BPF (Benjamin Tissoires)

The history is a little long for this series, as it was intended to be
sent for v6.2. However some last minute issues forced us to postpone it
to v6.3.

Conflicts:
* drivers/hid/i2c-hid/Kconfig:
  commit bf7660dab30d ("HID: stop drivers from selecting CONFIG_HID")
  conflicts with commit 2afac81dd165 ("HID: fix I2C_HID not selected
  when I2C_HID_OF_ELAN is")
  the resolution is simple enough: just drop the "default" and "select"
  lines as the new commit from Arnd is doing