The DSI/HDMI PLLs in MSM require resources like interface clocks, power
domains to be enabled before we can access their registers.

The clock framework doesn't have a mechanism at the moment where we can
tie such resources to a clock, so we make sure that the KMS driver enables
these resources whenever a PLL is expected to be in use.

One place where we can't ensure the resource dependencies are met is when
the clock framework tries to disable unused clocks. The KMS driver doesn't
know when the clock framework calls the is_enabled clk_op, and hence can't
enable interface clocks/power domains beforehand.

We set the CLK_IGNORE_UNUSED flag for PLL clocks for now. This needs to be
revisited, since bootloaders can enable display, and we would want to
disable the PLL clocks if there isn't a display driver using them.

Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

The msm/dsi host drivers calls drm_helper_hpd_irq_event in the
mipi_dsi_host attach/detatch callbacks.

mipi_dsi_attach()/mipi_dsi_detach() from a panel/bridge
driver could be called from a context where the drm_device's
mode_config.mutex is already held, resulting in a deadlock.
Queue it as work instead.

Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

In case of error, the function drm_mode_duplicate() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

Before we can add vmap shrinking, we really need to know which vmap'ings
are currently being used.  So switch to get/put interface.  Stubbed put
fxns for now.

Signed-off-by: Rob Clark <robdclark@gmail.com>

The DSI host and PHY driver currently expects the DT bindings to provide
custom properties "qcom,dsi-host-index" and "qcom,dsi-phy-index" so that
the driver can identify which DSI instance it is.

The binding isn't acceptable, but the driver still needs to figure out
what its instance id. This is now done by storing the mmio starting
addresses for each DSI instance in every SoC version in the driver. The
driver then identifies the index number by trying to match the stored
address with comparing the resource start address we get from DT.

We don't have compatible strings for DSI PHY on each SoC, but only the
DSI PHY type. We only support one SoC version for each PHY type, so we
get away doing the same thing above for the PHY driver. We can revisit
this when we support two SoCs with the same DSI PHY.

Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

A more standard DT binding describing data lanes already exists here:
Documentation/devicetree/bindings/media/video-interfaces.txt

Use this binding instead of "qcom,data-lane-map". One difference
in the standard binding w.r.t to the existing binding is that it
provides a logical to physical mapping instead of the other way
round. Tweak the code to translate the data the way we want it.

The MSM DSI DT bindings aren't used anywhere at the moment, so
it's okay to update this property.

Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

The DSI host links to the DSI PHY device using a custom binding. Switch to
the generic PHY bindings. The DSI PHY driver itself doesn't use the common
PHY framework for now.

Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

The DSI interface is going to have two ports defined in its device node.
The first port is always going to be the link between the MDP output
and the input to DSI, the second port is going to be the link between
the DSI output and the connected panel/bridge:

 -----           -----           -------
| MDP | ------> | DSI | ------> | Panel |
 -----           -----           -------
        (Port 0)       (Port 1)

Until now, there was only one Port representing the output. Update the
DSI host driver such that it parses Port #1 for a connected device.

Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

Move the drm_connector registration from the encoder(HDMI/DSI etc) drivers
to the msm platform driver. This will simplify the task of ensuring that
the connectors are registered only after the drm_device itself is
registered.

The connectors' destroy ops are made to use kzalloc instead of
devm_kzalloc to ensure that that the connectors can be successfully
unregistered when the msm driver module is removed. The memory for the
connectors is unallocated when drm_mode_config_cleanup() is called
during either during an error or during driver remove.

Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

The voltage changing code in this driver is broken and should be
removed.  The driver sets a single, exact voltage on probe.  Unless
there is a very good reason for this (which should be documented in
comments) constraints like this need to be set via the machine
constraints, voltage setting in a driver is expected to be used in cases
where the voltage varies at runtime.

In addition client drivers should almost never be calling
regulator_can_set_voltage(), if the device needs to set a voltage it
needs to set the voltage and the regulator core will handle the case
where the regulator is fixed voltage.  If the driver simply skips
setting the voltage if it doesn't have permission then it should just
not bother in the first place.

Originally authored by Mark Brown <broonie@kernel.org>

Remove the min/max voltage data entries per SoC managed by the driver.
These aren't needed as we don't try to set voltages any more. Mention in
comments the voltages that each regulator expects.

Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>