linux.git/drivers/gpu/drm/bridge, branch v6.8-rc2 Linux kernel source tree drm: bridge: samsung-dsim: Don't use FORCE_STOP_STATE 2024-01-26T13:48:47+00:00 Michael Walle mwalle@kernel.org 2023-11-13T16:43:44+00:00 ff3d5d04db07e5374758baa7e877fde8d683ebab The FORCE_STOP_STATE bit is unsuitable to force the DSI link into LP-11 mode. It seems the bridge internally queues DSI packets and when the FORCE_STOP_STATE bit is cleared, they are sent in close succession without any useful timing (this also means that the DSI lanes won't go into LP-11 mode). The length of this gibberish varies between 1ms and 5ms. This sometimes breaks an attached bridge (TI SN65DSI84 in this case). In our case, the bridge will fail in about 1 per 500 reboots. The FORCE_STOP_STATE handling was introduced to have the DSI lanes in LP-11 state during the .pre_enable phase. But as it turns out, none of this is needed at all. Between samsung_dsim_init() and samsung_dsim_set_display_enable() the lanes are already in LP-11 mode. The code as it was before commit 20c827683de0 ("drm: bridge: samsung-dsim: Fix init during host transfer") and 0c14d3130654 ("drm: bridge: samsung-dsim: Fix i.MX8M enable flow to meet spec") was correct in this regard. This patch basically reverts both commits. It was tested on an i.MX8M SoC with an SN65DSI84 bridge. The signals were probed and the DSI packets were decoded during initialization and link start-up. After this patch the first DSI packet on the link is a VSYNC packet and the timing is correct. Command mode between .pre_enable and .enable was also briefly tested by a quick hack. There was no DSI link partner which would have responded, but it was made sure the DSI packet was send on the link. As a side note, the command mode seems to just work in HS mode. I couldn't find that the bridge will handle commands in LP mode. Fixes: 20c827683de0 ("drm: bridge: samsung-dsim: Fix init during host transfer") Fixes: 0c14d3130654 ("drm: bridge: samsung-dsim: Fix i.MX8M enable flow to meet spec") Signed-off-by: Michael Walle <mwalle@kernel.org> Signed-off-by: Inki Dae <inki.dae@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/20231113164344.1612602-1-mwalle@kernel.org 
The FORCE_STOP_STATE bit is unsuitable to force the DSI link into LP-11
mode. It seems the bridge internally queues DSI packets and when the
FORCE_STOP_STATE bit is cleared, they are sent in close succession
without any useful timing (this also means that the DSI lanes won't go
into LP-11 mode). The length of this gibberish varies between 1ms and
5ms. This sometimes breaks an attached bridge (TI SN65DSI84 in this
case). In our case, the bridge will fail in about 1 per 500 reboots.

The FORCE_STOP_STATE handling was introduced to have the DSI lanes in
LP-11 state during the .pre_enable phase. But as it turns out, none of
this is needed at all. Between samsung_dsim_init() and
samsung_dsim_set_display_enable() the lanes are already in LP-11 mode.
The code as it was before commit 20c827683de0 ("drm: bridge:
samsung-dsim: Fix init during host transfer") and 0c14d3130654 ("drm:
bridge: samsung-dsim: Fix i.MX8M enable flow to meet spec") was correct
in this regard.

This patch basically reverts both commits. It was tested on an i.MX8M
SoC with an SN65DSI84 bridge. The signals were probed and the DSI
packets were decoded during initialization and link start-up. After this
patch the first DSI packet on the link is a VSYNC packet and the timing
is correct.

Command mode between .pre_enable and .enable was also briefly tested by
a quick hack. There was no DSI link partner which would have responded,
but it was made sure the DSI packet was send on the link. As a side
note, the command mode seems to just work in HS mode. I couldn't find
that the bridge will handle commands in LP mode.

Fixes: 20c827683de0 ("drm: bridge: samsung-dsim: Fix init during host transfer")
Fixes: 0c14d3130654 ("drm: bridge: samsung-dsim: Fix i.MX8M enable flow to meet spec")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231113164344.1612602-1-mwalle@kernel.org
drm/bridge: anx7625: Ensure bridge is suspended in disable() 2024-01-22T16:53:42+00:00 Hsin-Yi Wang hsinyi@chromium.org 2024-01-18T01:58:14+00:00 4d5b7daa3c610af3f322ad1e91fc0c752ff32f0e Similar to commit 26db46bc9c67 ("drm/bridge: parade-ps8640: Ensure bridge is suspended in .post_disable()"). Add a mutex to ensure that aux transfer won't race with atomic_disable by holding the PM reference and prevent the bridge from suspend. Also we need to use pm_runtime_put_sync_suspend() to suspend the bridge instead of idle with pm_runtime_put_sync(). Fixes: 3203e497eb76 ("drm/bridge: anx7625: Synchronously run runtime suspend.") Fixes: adca62ec370c ("drm/bridge: anx7625: Support reading edid through aux channel") Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org> Tested-by: Xuxin Xiong <xuxinxiong@huaqin.corp-partner.google.com> Reviewed-by: Pin-yen Lin <treapking@chromium.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Douglas Anderson <dianders@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20240118015916.2296741-1-hsinyi@chromium.org 
Similar to commit 26db46bc9c67 ("drm/bridge: parade-ps8640: Ensure bridge
is suspended in .post_disable()"). Add a mutex to ensure that aux transfer
won't race with atomic_disable by holding the PM reference and prevent
the bridge from suspend.

Also we need to use pm_runtime_put_sync_suspend() to suspend the bridge
instead of idle with pm_runtime_put_sync().

Fixes: 3203e497eb76 ("drm/bridge: anx7625: Synchronously run runtime suspend.")
Fixes: adca62ec370c ("drm/bridge: anx7625: Support reading edid through aux channel")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Tested-by: Xuxin Xiong <xuxinxiong@huaqin.corp-partner.google.com>
Reviewed-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240118015916.2296741-1-hsinyi@chromium.org
Merge v6.8-rc1 into drm-misc-fixes 2024-01-22T08:44:15+00:00 Maxime Ripard mripard@kernel.org 2024-01-22T08:44:15+00:00 cf79f291f985662150363b4a93d16f88f12643bc Let's kickstart the 6.8 fix cycle. Signed-off-by: Maxime Ripard <mripard@kernel.org> 
Let's kickstart the 6.8 fix cycle.

Signed-off-by: Maxime Ripard <mripard@kernel.org>
Merge tag 'i2c-for-6.8-rc1-rebased' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux 2024-01-19T01:29:01+00:00 Linus Torvalds torvalds@linux-foundation.org 2024-01-19T01:29:01+00:00 ed8d84530ab0a3b7b370e8b28f12179314dcfcc3 Pull i2c updates from Wolfram Sang: "This removes the currently unused CLASS_DDC support (controllers set the flag, but there is no client to use it). Also, CLASS_SPD support gets simplified to prepare removal in the future. Class based instantiation is not recommended these days anyhow. Furthermore, I2C core now creates a debugfs directory per I2C adapter. Current bus driver users were converted to use it. Finally, quite some driver updates. Standing out are patches for the wmt-driver which is refactored to support more variants. This is the rebased pull request where a large series for the designware driver was dropped" * tag 'i2c-for-6.8-rc1-rebased' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (38 commits) MAINTAINERS: use proper email for my I2C work i2c: stm32f7: add support for stm32mp25 soc i2c: stm32f7: perform I2C_ISR read once at beginning of event isr dt-bindings: i2c: document st,stm32mp25-i2c compatible i2c: stm32f7: simplify status messages in case of errors i2c: stm32f7: perform most of irq job in threaded handler i2c: stm32f7: use dev_err_probe upon calls of devm_request_irq i2c: i801: Add lis3lv02d for Dell XPS 15 7590 i2c: i801: Add lis3lv02d for Dell Precision 3540 i2c: wmt: Reduce redundant: REG_CR setting i2c: wmt: Reduce redundant: function parameter i2c: wmt: Reduce redundant: clock mode setting i2c: wmt: Reduce redundant: wait event complete i2c: wmt: Reduce redundant: bus busy check i2c: mux: reg: Remove class-based device auto-detection support i2c: make i2c_bus_type const dt-bindings: at24: add ROHM BR24G04 eeprom: at24: use of_match_ptr() i2c: cpm: Remove linux,i2c-index conversion from be32 i2c: imx: Make SDA actually optional for bus recovering ... 
Pull i2c updates from Wolfram Sang:
 "This removes the currently unused CLASS_DDC support (controllers set
  the flag, but there is no client to use it).

  Also, CLASS_SPD support gets simplified to prepare removal in the
  future. Class based instantiation is not recommended these days
  anyhow.

  Furthermore, I2C core now creates a debugfs directory per I2C adapter.
  Current bus driver users were converted to use it.

  Finally, quite some driver updates. Standing out are patches for the
  wmt-driver which is refactored to support more variants.

  This is the rebased pull request where a large series for the
  designware driver was dropped"

* tag 'i2c-for-6.8-rc1-rebased' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (38 commits)
  MAINTAINERS: use proper email for my I2C work
  i2c: stm32f7: add support for stm32mp25 soc
  i2c: stm32f7: perform I2C_ISR read once at beginning of event isr
  dt-bindings: i2c: document st,stm32mp25-i2c compatible
  i2c: stm32f7: simplify status messages in case of errors
  i2c: stm32f7: perform most of irq job in threaded handler
  i2c: stm32f7: use dev_err_probe upon calls of devm_request_irq
  i2c: i801: Add lis3lv02d for Dell XPS 15 7590
  i2c: i801: Add lis3lv02d for Dell Precision 3540
  i2c: wmt: Reduce redundant: REG_CR setting
  i2c: wmt: Reduce redundant: function parameter
  i2c: wmt: Reduce redundant: clock mode setting
  i2c: wmt: Reduce redundant: wait event complete
  i2c: wmt: Reduce redundant: bus busy check
  i2c: mux: reg: Remove class-based device auto-detection support
  i2c: make i2c_bus_type const
  dt-bindings: at24: add ROHM BR24G04
  eeprom: at24: use of_match_ptr()
  i2c: cpm: Remove linux,i2c-index conversion from be32
  i2c: imx: Make SDA actually optional for bus recovering
  ...
drm: remove I2C_CLASS_DDC support 2024-01-18T20:10:41+00:00 Heiner Kallweit hkallweit1@gmail.com 2023-11-23T09:40:21+00:00 e965a707276760cc010eb77fba64b08ee9e8781f After removal of the legacy EEPROM driver and I2C_CLASS_DDC support in olpc_dcon there's no i2c client driver left supporting I2C_CLASS_DDC. Class-based device auto-detection is a legacy mechanism and shouldn't be used in new code. So we can remove this class completely now. Acked-by: Alex Deucher <alexander.deucher@amd.com> Acked-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Acked-by: Harry Wentland <harry.wentland@amd.com> Acked-by: Heiko Stuebner <heiko@sntech.de> Acked-by: Jani Nikula <jani.nikula@intel.com> Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com> Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de> Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> 
After removal of the legacy EEPROM driver and I2C_CLASS_DDC support in
olpc_dcon there's no i2c client driver left supporting I2C_CLASS_DDC.
Class-based device auto-detection is a legacy mechanism and shouldn't
be used in new code. So we can remove this class completely now.

Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
drm/bridge: parade-ps8640: Make sure we drop the AUX mutex in the error case 2024-01-17T20:08:02+00:00 Douglas Anderson dianders@chromium.org 2024-01-17T18:35:03+00:00 a20f1b02bafcbf5a32d96a1d4185d6981cf7d016 After commit 26db46bc9c67 ("drm/bridge: parade-ps8640: Ensure bridge is suspended in .post_disable()"), if we hit the error case in ps8640_aux_transfer() then we return without dropping the mutex. Fix this oversight. Fixes: 26db46bc9c67 ("drm/bridge: parade-ps8640: Ensure bridge is suspended in .post_disable()") Reviewed-by: Hsin-Yi Wang <hsinyi@chromium.org> Signed-off-by: Douglas Anderson <dianders@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20240117103502.1.Ib726a0184913925efc7e99c4d4fc801982e1bc24@changeid 
After commit 26db46bc9c67 ("drm/bridge: parade-ps8640: Ensure bridge
is suspended in .post_disable()"), if we hit the error case in
ps8640_aux_transfer() then we return without dropping the mutex. Fix
this oversight.

Fixes: 26db46bc9c67 ("drm/bridge: parade-ps8640: Ensure bridge is suspended in .post_disable()")
Reviewed-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240117103502.1.Ib726a0184913925efc7e99c4d4fc801982e1bc24@changeid
drm/bridge: parade-ps8640: Ensure bridge is suspended in .post_disable() 2024-01-17T17:29:40+00:00 Pin-yen Lin treapking@chromium.org 2024-01-09T12:04:57+00:00 26db46bc9c675e43230cc6accd110110a7654299 The ps8640 bridge seems to expect everything to be power cycled at the disable process, but sometimes ps8640_aux_transfer() holds the runtime PM reference and prevents the bridge from suspend. Prevent that by introducing a mutex lock between ps8640_aux_transfer() and .post_disable() to make sure the bridge is really powered off. Fixes: 826cff3f7ebb ("drm/bridge: parade-ps8640: Enable runtime power management") Signed-off-by: Pin-yen Lin <treapking@chromium.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Douglas Anderson <dianders@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20240109120528.1292601-1-treapking@chromium.org 
The ps8640 bridge seems to expect everything to be power cycled at the
disable process, but sometimes ps8640_aux_transfer() holds the runtime
PM reference and prevents the bridge from suspend.

Prevent that by introducing a mutex lock between ps8640_aux_transfer()
and .post_disable() to make sure the bridge is really powered off.

Fixes: 826cff3f7ebb ("drm/bridge: parade-ps8640: Enable runtime power management")
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240109120528.1292601-1-treapking@chromium.org
drm/bridge: sii902x: Fix audio codec unregistration 2024-01-16T08:58:16+00:00 Tomi Valkeinen tomi.valkeinen@ideasonboard.com 2024-01-03T13:31:08+00:00 3fc6c76a8d208d3955c9e64b382d0ff370bc61fc The driver never unregisters the audio codec platform device, which can lead to a crash on module reloading, nor does it handle the return value from sii902x_audio_codec_init(). Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> Fixes: ff5781634c41 ("drm/bridge: sii902x: Implement HDMI audio support") Cc: Jyri Sarha <jsarha@ti.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20240103-si902x-fixes-v1-2-b9fd3e448411@ideasonboard.com Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20240103-si902x-fixes-v1-2-b9fd3e448411@ideasonboard.com 
The driver never unregisters the audio codec platform device, which can
lead to a crash on module reloading, nor does it handle the return value
from sii902x_audio_codec_init().

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Fixes: ff5781634c41 ("drm/bridge: sii902x: Implement HDMI audio support")
Cc: Jyri Sarha <jsarha@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240103-si902x-fixes-v1-2-b9fd3e448411@ideasonboard.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240103-si902x-fixes-v1-2-b9fd3e448411@ideasonboard.com
drm/bridge: sii902x: Fix probing race issue 2024-01-16T08:58:15+00:00 Tomi Valkeinen tomi.valkeinen@ideasonboard.com 2024-01-03T13:31:07+00:00 08ac6f132dd77e40f786d8af51140c96c6d739c9 A null pointer dereference crash has been observed rarely on TI platforms using sii9022 bridge: [ 53.271356] sii902x_get_edid+0x34/0x70 [sii902x] [ 53.276066] sii902x_bridge_get_edid+0x14/0x20 [sii902x] [ 53.281381] drm_bridge_get_edid+0x20/0x34 [drm] [ 53.286305] drm_bridge_connector_get_modes+0x8c/0xcc [drm_kms_helper] [ 53.292955] drm_helper_probe_single_connector_modes+0x190/0x538 [drm_kms_helper] [ 53.300510] drm_client_modeset_probe+0x1f0/0xbd4 [drm] [ 53.305958] __drm_fb_helper_initial_config_and_unlock+0x50/0x510 [drm_kms_helper] [ 53.313611] drm_fb_helper_initial_config+0x48/0x58 [drm_kms_helper] [ 53.320039] drm_fbdev_dma_client_hotplug+0x84/0xd4 [drm_dma_helper] [ 53.326401] drm_client_register+0x5c/0xa0 [drm] [ 53.331216] drm_fbdev_dma_setup+0xc8/0x13c [drm_dma_helper] [ 53.336881] tidss_probe+0x128/0x264 [tidss] [ 53.341174] platform_probe+0x68/0xc4 [ 53.344841] really_probe+0x188/0x3c4 [ 53.348501] __driver_probe_device+0x7c/0x16c [ 53.352854] driver_probe_device+0x3c/0x10c [ 53.357033] __device_attach_driver+0xbc/0x158 [ 53.361472] bus_for_each_drv+0x88/0xe8 [ 53.365303] __device_attach+0xa0/0x1b4 [ 53.369135] device_initial_probe+0x14/0x20 [ 53.373314] bus_probe_device+0xb0/0xb4 [ 53.377145] deferred_probe_work_func+0xcc/0x124 [ 53.381757] process_one_work+0x1f0/0x518 [ 53.385770] worker_thread+0x1e8/0x3dc [ 53.389519] kthread+0x11c/0x120 [ 53.392750] ret_from_fork+0x10/0x20 The issue here is as follows: - tidss probes, but is deferred as sii902x is still missing. - sii902x starts probing and enters sii902x_init(). - sii902x calls drm_bridge_add(). Now the sii902x bridge is ready from DRM's perspective. - sii902x calls sii902x_audio_codec_init() and platform_device_register_data() - The registration of the audio platform device causes probing of the deferred devices. - tidss probes, which eventually causes sii902x_bridge_get_edid() to be called. - sii902x_bridge_get_edid() tries to use the i2c to read the edid. However, the sii902x driver has not set up the i2c part yet, leading to the crash. Fix this by moving the drm_bridge_add() to the end of the sii902x_init(), which is also at the very end of sii902x_probe(). Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> Fixes: 21d808405fe4 ("drm/bridge/sii902x: Fix EDID readback") Acked-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20240103-si902x-fixes-v1-1-b9fd3e448411@ideasonboard.com Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20240103-si902x-fixes-v1-1-b9fd3e448411@ideasonboard.com 
A null pointer dereference crash has been observed rarely on TI
platforms using sii9022 bridge:

[   53.271356]  sii902x_get_edid+0x34/0x70 [sii902x]
[   53.276066]  sii902x_bridge_get_edid+0x14/0x20 [sii902x]
[   53.281381]  drm_bridge_get_edid+0x20/0x34 [drm]
[   53.286305]  drm_bridge_connector_get_modes+0x8c/0xcc [drm_kms_helper]
[   53.292955]  drm_helper_probe_single_connector_modes+0x190/0x538 [drm_kms_helper]
[   53.300510]  drm_client_modeset_probe+0x1f0/0xbd4 [drm]
[   53.305958]  __drm_fb_helper_initial_config_and_unlock+0x50/0x510 [drm_kms_helper]
[   53.313611]  drm_fb_helper_initial_config+0x48/0x58 [drm_kms_helper]
[   53.320039]  drm_fbdev_dma_client_hotplug+0x84/0xd4 [drm_dma_helper]
[   53.326401]  drm_client_register+0x5c/0xa0 [drm]
[   53.331216]  drm_fbdev_dma_setup+0xc8/0x13c [drm_dma_helper]
[   53.336881]  tidss_probe+0x128/0x264 [tidss]
[   53.341174]  platform_probe+0x68/0xc4
[   53.344841]  really_probe+0x188/0x3c4
[   53.348501]  __driver_probe_device+0x7c/0x16c
[   53.352854]  driver_probe_device+0x3c/0x10c
[   53.357033]  __device_attach_driver+0xbc/0x158
[   53.361472]  bus_for_each_drv+0x88/0xe8
[   53.365303]  __device_attach+0xa0/0x1b4
[   53.369135]  device_initial_probe+0x14/0x20
[   53.373314]  bus_probe_device+0xb0/0xb4
[   53.377145]  deferred_probe_work_func+0xcc/0x124
[   53.381757]  process_one_work+0x1f0/0x518
[   53.385770]  worker_thread+0x1e8/0x3dc
[   53.389519]  kthread+0x11c/0x120
[   53.392750]  ret_from_fork+0x10/0x20

The issue here is as follows:

- tidss probes, but is deferred as sii902x is still missing.
- sii902x starts probing and enters sii902x_init().
- sii902x calls drm_bridge_add(). Now the sii902x bridge is ready from
  DRM's perspective.
- sii902x calls sii902x_audio_codec_init() and
  platform_device_register_data()
- The registration of the audio platform device causes probing of the
  deferred devices.
- tidss probes, which eventually causes sii902x_bridge_get_edid() to be
  called.
- sii902x_bridge_get_edid() tries to use the i2c to read the edid.
  However, the sii902x driver has not set up the i2c part yet, leading
  to the crash.

Fix this by moving the drm_bridge_add() to the end of the
sii902x_init(), which is also at the very end of sii902x_probe().

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Fixes: 21d808405fe4 ("drm/bridge/sii902x: Fix EDID readback")
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240103-si902x-fixes-v1-1-b9fd3e448411@ideasonboard.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240103-si902x-fixes-v1-1-b9fd3e448411@ideasonboard.com
Merge tag 'drm-next-2024-01-10' of git://anongit.freedesktop.org/drm/drm 2024-01-12T19:32:19+00:00 Linus Torvalds torvalds@linux-foundation.org 2024-01-12T19:32:19+00:00 cf65598d5909acf5e7b7dc9e21786e386356bc81 Pull drm updates from Dave Airlie: "This contains two major new drivers: - imagination is a first driver for Imagination Technologies devices, it only covers very specific devices, but there is hope to grow it - xe is a reboot of the i915 GPU (shares display) side using a more upstream focused development model, and trying to maximise code sharing. It's not enabled for any hw by default, and will hopefully get switched on for Intel's Lunarlake. This also drops a bunch of the old UMS ioctls. It's been dead long enough. amdgpu has a bunch of new color management code that is being used in the Steam Deck. amdgpu also has a new ACPI WBRF interaction to help avoid radio interference. Otherwise it's the usual lots of changes in lots of places. Detailed summary: new drivers: - imagination - new driver for Imagination Technologies GPU - xe - new driver for Intel GPUs using core drm concepts core: - add CLOSE_FB ioctl - remove old UMS ioctls - increase max objects to accomodate AMD color mgmt encoder: - create per-encoder debugfs directory edid: - split out drm_eld - SAD helpers - drop edid_firmware module parameter format-helper: - cache format conversion buffers sched: - move from kthread to workqueue - rename some internals - implement dynamic job-flow control gpuvm: - provide more features to handle GEM objects client: - don't acquire module reference displayport: - add mst path property documentation fdinfo: - alignment fix dma-buf: - add fence timestamp helper - add fence deadline support bridge: - transparent aux-bridge for DP/USB-C - lt8912b: add suspend/resume support and power regulator support panel: - edp: AUO B116XTN02, BOE NT116WHM-N21,836X2, NV116WHM-N49 - chromebook panel support - elida-kd35t133: rework pm - powkiddy RK2023 panel - himax-hx8394: drop prepare/unprepare and shutdown logic - BOE BP101WX1-100, Powkiddy X55, Ampire AM8001280G - Evervision VGG644804, SDC ATNA45AF01 - nv3052c: register docs, init sequence fixes, fascontek FS035VG158 - st7701: Anbernic RG-ARC support - r63353 panel controller - Ilitek ILI9805 panel controller - AUO G156HAN04.0 simplefb: - support memory regions - support power domains amdgpu: - add new 64-bit sequence number infrastructure - add AMD specific color management - ACPI WBRF support for RF interference handling - GPUVM updates - RAS updates - DCN 3.5 updates - Rework PCIe link speed handling - Document GPU reset types - DMUB fixes - eDP fixes - NBIO 7.9/7.11 updates - SubVP updates - XGMI PCIe state dumping for aqua vanjaram - GFX11 golden register updates - enable tunnelling on high pri compute amdkfd: - Migrate TLB flushing logic to amdgpu - Trap handler fixes - Fix restore workers handling on suspend/resume - Fix possible memory leak in pqm_uninit() - support import/export of dma-bufs using GEM handles radeon: - fix possible overflows in command buffer checking - check for errors in ring_lock i915: - reorg display code for reuse in xe driver - fdinfo memory stats printing - DP MST bandwidth mgmt improvements - DP panel replay enabling - MTL C20 phy state verification - MTL DP DSC fractional bpp support - Audio fastset support - use dma_fence interfaces instead of i915_sw_fence - Separate gem and display code - AUX register macro refactoring - Separate display module/device parameters - Move display capabilities debugfs under display - Makefile cleanups - Register cleanups - Move display lock inits under display/ - VLV/CHV DPIO PHY register and interface refactoring - DSI VBT sequence refactoring - C10/C20 PHY PLL hardware readout - DPLL code cleanups - Cleanup PXP plane protection checks - Improve display debug msgs - PSR selective fetch fixes/improvements - DP MST fixes - Xe2LPD FBC restrictions removed - DGFX uses direct VBT pin mapping - more MTL WAs - fix MTL eDP bug - eliminate use of kmap_atomic habanalabs: - sysfs entry to identify a device minor id with debugfs path - sysfs entry to expose device module id - add signed device info retrieval through INFO ioctl - add Gaudi2C device support - pcie reset prepare/done hooks msm: - Add support for SDM670, SM8650 - Handle the CFG interconnect to fix the obscure hangs / timeouts - Kconfig fix for QMP dependency - use managed allocators - DPU: SDM670, SM8650 support - DPU: Enable SmartDMA on SM8350 and SM8450 - DP: enable runtime PM support - GPU: add metadata UAPI - GPU: move devcoredumps to GPU device - GPU: convert to drm_exec ivpu: - update FW API - new debugfs file - a new NOP job submission test mode - improve suspend/resume - PM improvements - MMU PT optimizations - firmware profile frequency support - support for uncached buffers - switch to gem shmem helpers - replace kthread with threaded irqs rockchip: - rk3066_hdmi: convert to atomic - vop2: support nv20 and nv30 - rk3588 support mediatek: - use devm_platform_ioremap_resource - stop using iommu_present - MT8188 VDOSYS1 display support panfrost: - PM improvements - improve interrupt handling as poweroff qaic: - allow to run with single MSI - support host/device time sync - switch to persistent DRM devices exynos: - fix potential error pointer dereference - fix wrong error checking - add missing call to drm_atomic_helper_shutdown omapdrm: - dma-fence lockdep annotation fix tidss: - dma-fence lockdep annotation fix - support for AM62A7 v3d: - BCM2712 - rpi5 support - fdinfo + gputop support - uapi for CPU job handling virtio-gpu: - add context debug name" * tag 'drm-next-2024-01-10' of git://anongit.freedesktop.org/drm/drm: (2340 commits) drm/amd/display: Allow z8/z10 from driver drm/amd/display: fix bandwidth validation failure on DCN 2.1 drm/amdgpu: apply the RV2 system aperture fix to RN/CZN as well drm/amd/display: Move fixpt_from_s3132 to amdgpu_dm drm/amd/display: Fix recent checkpatch errors in amdgpu_dm Revert "drm/amdkfd: Relocate TBA/TMA to opposite side of VM hole" drm/amd/display: avoid stringop-overflow warnings for dp_decide_lane_settings() drm/amd/display: Fix power_helpers.c codestyle drm/amd/display: Fix hdcp_log.h codestyle drm/amd/display: Fix hdcp2_execution.c codestyle drm/amd/display: Fix hdcp_psp.h codestyle drm/amd/display: Fix freesync.c codestyle drm/amd/display: Fix hdcp_psp.c codestyle drm/amd/display: Fix hdcp1_execution.c codestyle drm/amd/pm/smu7: fix a memleak in smu7_hwmgr_backend_init drm/amdkfd: Fix iterator used outside loop in 'kfd_add_peer_prop()' drm/amdgpu: Drop 'fence' check in 'to_amdgpu_amdkfd_fence()' drm/amdkfd: Confirm list is non-empty before utilizing list_first_entry in kfd_topology.c drm/amdgpu: Fix '*fw' from request_firmware() not released in 'amdgpu_ucode_request()' drm/amdgpu: Fix variable 'mca_funcs' dereferenced before NULL check in 'amdgpu_mca_smu_get_mca_entry()' ... 
Pull drm updates from Dave Airlie:
 "This contains two major new drivers:

   - imagination is a first driver for Imagination Technologies devices,
     it only covers very specific devices, but there is hope to grow it

   - xe is a reboot of the i915 GPU (shares display) side using a more
     upstream focused development model, and trying to maximise code
     sharing. It's not enabled for any hw by default, and will hopefully
     get switched on for Intel's Lunarlake.

  This also drops a bunch of the old UMS ioctls. It's been dead long
  enough.

  amdgpu has a bunch of new color management code that is being used in
  the Steam Deck.

  amdgpu also has a new ACPI WBRF interaction to help avoid radio
  interference.

  Otherwise it's the usual lots of changes in lots of places.

  Detailed summary:

  new drivers:
   - imagination - new driver for Imagination Technologies GPU
   - xe - new driver for Intel GPUs using core drm concepts

  core:
   - add CLOSE_FB ioctl
   - remove old UMS ioctls
   - increase max objects to accomodate AMD color mgmt

  encoder:
   - create per-encoder debugfs directory

  edid:
   - split out drm_eld
   - SAD helpers
   - drop edid_firmware module parameter

  format-helper:
   - cache format conversion buffers

  sched:
   - move from kthread to workqueue
   - rename some internals
   - implement dynamic job-flow control

  gpuvm:
   - provide more features to handle GEM objects

  client:
   - don't acquire module reference

  displayport:
   - add mst path property documentation

  fdinfo:
   - alignment fix

  dma-buf:
   - add fence timestamp helper
   - add fence deadline support

  bridge:
   - transparent aux-bridge for DP/USB-C
   - lt8912b: add suspend/resume support and power regulator support

  panel:
   - edp: AUO B116XTN02, BOE NT116WHM-N21,836X2, NV116WHM-N49
   - chromebook panel support
   - elida-kd35t133: rework pm
   - powkiddy RK2023 panel
   - himax-hx8394: drop prepare/unprepare and shutdown logic
   - BOE BP101WX1-100, Powkiddy X55, Ampire AM8001280G
   - Evervision VGG644804, SDC ATNA45AF01
   - nv3052c: register docs, init sequence fixes, fascontek FS035VG158
   - st7701: Anbernic RG-ARC support
   - r63353 panel controller
   - Ilitek ILI9805 panel controller
   - AUO G156HAN04.0

  simplefb:
   - support memory regions
   - support power domains

  amdgpu:
   - add new 64-bit sequence number infrastructure
   - add AMD specific color management
   - ACPI WBRF support for RF interference handling
   - GPUVM updates
   - RAS updates
   - DCN 3.5 updates
   - Rework PCIe link speed handling
   - Document GPU reset types
   - DMUB fixes
   - eDP fixes
   - NBIO 7.9/7.11 updates
   - SubVP updates
   - XGMI PCIe state dumping for aqua vanjaram
   - GFX11 golden register updates
   - enable tunnelling on high pri compute

  amdkfd:
   - Migrate TLB flushing logic to amdgpu
   - Trap handler fixes
   - Fix restore workers handling on suspend/resume
   - Fix possible memory leak in pqm_uninit()
   - support import/export of dma-bufs using GEM handles

  radeon:
   - fix possible overflows in command buffer checking
   - check for errors in ring_lock

  i915:
   - reorg display code for reuse in xe driver
   - fdinfo memory stats printing
   - DP MST bandwidth mgmt improvements
   - DP panel replay enabling
   - MTL C20 phy state verification
   - MTL DP DSC fractional bpp support
   - Audio fastset support
   - use dma_fence interfaces instead of i915_sw_fence
   - Separate gem and display code
   - AUX register macro refactoring
   - Separate display module/device parameters
   - Move display capabilities debugfs under display
   - Makefile cleanups
   - Register cleanups
   - Move display lock inits under display/
   - VLV/CHV DPIO PHY register and interface refactoring
   - DSI VBT sequence refactoring
   - C10/C20 PHY PLL hardware readout
   - DPLL code cleanups
   - Cleanup PXP plane protection checks
   - Improve display debug msgs
   - PSR selective fetch fixes/improvements
   - DP MST fixes
   - Xe2LPD FBC restrictions removed
   - DGFX uses direct VBT pin mapping
   - more MTL WAs
   - fix MTL eDP bug
   - eliminate use of kmap_atomic

  habanalabs:
   - sysfs entry to identify a device minor id with debugfs path
   - sysfs entry to expose device module id
   - add signed device info retrieval through INFO ioctl
   - add Gaudi2C device support
   - pcie reset prepare/done hooks

  msm:
   - Add support for SDM670, SM8650
   - Handle the CFG interconnect to fix the obscure hangs / timeouts
   - Kconfig fix for QMP dependency
   - use managed allocators
   - DPU: SDM670, SM8650 support
   - DPU: Enable SmartDMA on SM8350 and SM8450
   - DP: enable runtime PM support
   - GPU: add metadata UAPI
   - GPU: move devcoredumps to GPU device
   - GPU: convert to drm_exec

  ivpu:
   - update FW API
   - new debugfs file
   - a new NOP job submission test mode
   - improve suspend/resume
   - PM improvements
   - MMU PT optimizations
   - firmware profile frequency support
   - support for uncached buffers
   - switch to gem shmem helpers
   - replace kthread with threaded irqs

  rockchip:
   - rk3066_hdmi: convert to atomic
   - vop2: support nv20 and nv30
   - rk3588 support

  mediatek:
   - use devm_platform_ioremap_resource
   - stop using iommu_present
   - MT8188 VDOSYS1 display support

  panfrost:
   - PM improvements
   - improve interrupt handling as poweroff

  qaic:
   - allow to run with single MSI
   - support host/device time sync
   - switch to persistent DRM devices

  exynos:
   - fix potential error pointer dereference
   - fix wrong error checking
   - add missing call to drm_atomic_helper_shutdown

  omapdrm:
   - dma-fence lockdep annotation fix

  tidss:
   - dma-fence lockdep annotation fix
   - support for AM62A7

  v3d:
   - BCM2712 - rpi5 support
   - fdinfo + gputop support
   - uapi for CPU job handling

  virtio-gpu:
   - add context debug name"

* tag 'drm-next-2024-01-10' of git://anongit.freedesktop.org/drm/drm: (2340 commits)
  drm/amd/display: Allow z8/z10 from driver
  drm/amd/display: fix bandwidth validation failure on DCN 2.1
  drm/amdgpu: apply the RV2 system aperture fix to RN/CZN as well
  drm/amd/display: Move fixpt_from_s3132 to amdgpu_dm
  drm/amd/display: Fix recent checkpatch errors in amdgpu_dm
  Revert "drm/amdkfd: Relocate TBA/TMA to opposite side of VM hole"
  drm/amd/display: avoid stringop-overflow warnings for dp_decide_lane_settings()
  drm/amd/display: Fix power_helpers.c codestyle
  drm/amd/display: Fix hdcp_log.h codestyle
  drm/amd/display: Fix hdcp2_execution.c codestyle
  drm/amd/display: Fix hdcp_psp.h codestyle
  drm/amd/display: Fix freesync.c codestyle
  drm/amd/display: Fix hdcp_psp.c codestyle
  drm/amd/display: Fix hdcp1_execution.c codestyle
  drm/amd/pm/smu7: fix a memleak in smu7_hwmgr_backend_init
  drm/amdkfd: Fix iterator used outside loop in 'kfd_add_peer_prop()'
  drm/amdgpu: Drop 'fence' check in 'to_amdgpu_amdkfd_fence()'
  drm/amdkfd: Confirm list is non-empty before utilizing list_first_entry in kfd_topology.c
  drm/amdgpu: Fix '*fw' from request_firmware() not released in 'amdgpu_ucode_request()'
  drm/amdgpu: Fix variable 'mca_funcs' dereferenced before NULL check in 'amdgpu_mca_smu_get_mca_entry()'
  ...