Pull drm updates from Dave Airlie:
 "The drm core grew a new generic gpu virtual address manager, and new
  execution locking helpers. These are used by nouveau now to provide
  uAPI support for the userspace Vulkan driver. AMD had a bunch of new
  IP core support, loads of refactoring around fbdev, but mostly just
  the usual amount of stuff across the board.

  core:
   - fix gfp flags in drmm_kmalloc

  gpuva:
   - add new generic GPU VA manager (for nouveau initially)

  syncobj:
   - add new DRM_IOCTL_SYNCOBJ_EVENTFD ioctl

  dma-buf:
   - acquire resv lock for mmap() in exporters
   - support dma-buf self import automatically
   - docs fixes

  backlight:
   - fix fbdev interactions

  atomic:
   - improve logging

  prime:
   - remove struct gem_prim_mmap plus driver updates

  gem:
   - drm_exec: add locking over multiple GEM objects
   - fix lockdep checking

  fbdev:
   - make fbdev userspace interfaces optional
   - use linux device instead of fbdev device
   - use deferred i/o helper macros in various drivers
   - Make FB core selectable without drivers
   - Remove obsolete flags FBINFO_DEFAULT and FBINFO_FLAG_DEFAULT
   - Add helper macros and Kconfig tokens for DMA-allocated framebuffer

  ttm:
   - support init_on_free
   - swapout fixes

  panel:
   - panel-edp: Support AUO B116XAB01.4
   - Support Visionox R66451 plus DT bindings
   - ld9040:
      - Backlight support
      - magic improved
      - Kconfig fix
   - Convert to of_device_get_match_data()
   - Fix Kconfig dependencies
   - simple:
      - Set bpc value to fix warning
      - Set connector type for AUO T215HVN01
      - Support Innolux G156HCE-L01 plus DT bindings
   - ili9881: Support TDO TL050HDV35 LCD panel plus DT bindings
   - startek: Support KD070FHFID015 MIPI-DSI panel plus DT bindings
   - sitronix-st7789v:
      - Support Inanbo T28CP45TN89 plus DT bindings
      - Support EDT ET028013DMA plus DT bindings
      - Various cleanups
   - edp: Add timings for N140HCA-EAC
   - Allow panels and touchscreens to power sequence together
   - Fix Innolux G156HCE-L01 LVDS clock

  bridge:
   - debugfs for chains support
   - dw-hdmi:
      - Improve support for YUV420 bus format
      - CEC suspend/resume
      - update EDID on HDMI detect
   - dw-mipi-dsi: Fix enable/disable of DSI controller
   - lt9611uxc: Use MODULE_FIRMWARE()
   - ps8640: Remove broken EDID code
   - samsung-dsim: Fix command transfer
   - tc358764:
      - Handle HS/VS polarity
      - Use BIT() macro
      - Various cleanups
   - adv7511: Fix low refresh rate
   - anx7625:
      - Switch to macros instead of hardcoded values
      - locking fixes
   - tc358767: fix hardware delays
   - sitronix-st7789v:
      - Support panel orientation
      - Support rotation property
      - Add support for Jasonic JT240MHQS-HWT-EK-E3 plus DT bindings

  amdgpu:
   - SDMA 6.1.0 support
   - HDP 6.1 support
   - SMUIO 14.0 support
   - PSP 14.0 support
   - IH 6.1 support
   - Lots of checkpatch cleanups
   - GFX 9.4.3 updates
   - Add USB PD and IFWI flashing documentation
   - GPUVM updates
   - RAS fixes
   - DRR fixes
   - FAMS fixes
   - Virtual display fixes
   - Soft IH fixes
   - SMU13 fixes
   - Rework PSP firmware loading for other IPs
   - Kernel doc fixes
   - DCN 3.0.1 fixes
   - LTTPR fixes
   - DP MST fixes
   - DCN 3.1.6 fixes
   - SMU 13.x fixes
   - PSP 13.x fixes
   - SubVP fixes
   - GC 9.4.3 fixes
   - Display bandwidth calculation fixes
   - VCN4 secure submission fixes
   - Allow building DC on RISC-V
   - Add visible FB info to bo_print_info
   - HBR3 fixes
   - GFX9 MCBP fix
   - GMC10 vmhub index fix
   - GMC11 vmhub index fix
   - Create a new doorbell manager
   - SR-IOV fixes
   - initial freesync panel replay support
   - revert zpos properly until igt regression is fixeed
   - use TTM to manage doorbell BAR
   - Expose both current and average power via hwmon if supported

  amdkfd:
   - Cleanup CRIU dma-buf handling
   - Use KIQ to unmap HIQ
   - GFX 9.4.3 debugger updates
   - GFX 9.4.2 debugger fixes
   - Enable cooperative groups fof gfx11
   - SVM fixes
   - Convert older APUs to use dGPU path like newer APUs
   - Drop IOMMUv2 path as it is no longer used
   - TBA fix for aldebaran

  i915:
   - ICL+ DSI modeset sequence
   - HDCP improvements
   - MTL display fixes and cleanups
   - HSW/BDW PSR1 restored
   - Init DDI ports in VBT order
   - General display refactors
   - Start using plane scale factor for relative data rate
   - Use shmem for dpt objects
   - Expose RPS thresholds in sysfs
   - Apply GuC SLPC min frequency softlimit correctly
   - Extend Wa_14015795083 to TGL, RKL, DG1 and ADL
   - Fix a VMA UAF for multi-gt platform
   - Do not use stolen on MTL due to HW bug
   - Check HuC and GuC version compatibility on MTL
   - avoid infinite GPU waits due to premature release of request memory
   - Fixes and updates for GSC memory allocation
   - Display SDVO fixes
   - Take stolen handling out of FBC code
   - Make i915_coherent_map_type GT-centric
   - Simplify shmem_create_from_object map_type

  msm:
   - SM6125 MDSS support
   - DPU: SM6125 DPU support
   - DSI: runtime PM support, burst mode support
   - DSI PHY: SM6125 support in 14nm DSI PHY driver
   - GPU: prepare for a7xx
   - fix a690 firmware
   - disable relocs on a6xx and newer

  radeon:
   - Lots of checkpatch cleanups

  ast:
   - improve device-model detection
   - Represent BMV as virtual connector
   - Report DP connection status

  nouveau:
   - add new exec/bind interface to support Vulkan
   - document some getparam ioctls
   - improve VRAM detection
   - various fixes/cleanups
   - workraound DPCD issues

  ivpu:
   - MMU updates
   - debugfs support
   - Support vpu4

  virtio:
   - add sync object support

  atmel-hlcdc:
   - Support inverted pixclock polarity

  etnaviv:
   - runtime PM cleanups
   - hang handling fixes

  exynos:
   - use fbdev DMA helpers
   - fix possible NULL ptr dereference

  komeda:
   - always attach encoder

  omapdrm:
   - use fbdev DMA helpers
ingenic:
   - kconfig regmap fixes

  loongson:
   - support display controller

  mediatek:
   - Small mtk-dpi cleanups
   - DisplayPort: support eDP and aux-bus
   - Fix coverity issues
   - Fix potential memory leak if vmap() fail

  mgag200:
   - minor fixes

  mxsfb:
   - support disabling overlay planes

  panfrost:
   - fix sync in IRQ handling

  ssd130x:
   - Support per-controller default resolution plus DT bindings
   - Reduce memory-allocation overhead
   - Improve intermediate buffer size computation
   - Fix allocation of temporary buffers
   - Fix pitch computation
   - Fix shadow plane allocation

  tegra:
   - use fbdev DMA helpers
   - Convert to devm_platform_ioremap_resource()
   - support bridge/connector
   - enable PM

  tidss:
   - Support TI AM625 plus DT bindings
   - Implement new connector model plus driver updates

  vkms:
   - improve write back support
   - docs fixes
   - support gamma LUT

  zynqmp-dpsub:
   - misc fixes"

* tag 'drm-next-2023-08-30' of git://anongit.freedesktop.org/drm/drm: (1327 commits)
  drm/gpuva_mgr: remove unused prev pointer in __drm_gpuva_sm_map()
  drm/tests/drm_kunit_helpers: Place correct function name in the comment header
  drm/nouveau: uapi: don't pass NO_PREFETCH flag implicitly
  drm/nouveau: uvmm: fix unset region pointer on remap
  drm/nouveau: sched: avoid job races between entities
  drm/i915: Fix HPD polling, reenabling the output poll work as needed
  drm: Add an HPD poll helper to reschedule the poll work
  drm/i915: Fix TLB-Invalidation seqno store
  drm/ttm/tests: Fix type conversion in ttm_pool_test
  drm/msm/a6xx: Bail out early if setting GPU OOB fails
  drm/msm/a6xx: Move LLC accessors to the common header
  drm/msm/a6xx: Introduce a6xx_llc_read
  drm/ttm/tests: Require MMU when testing
  drm/panel: simple: Fix Innolux G156HCE-L01 LVDS clock
  Revert "Revert "drm/amdgpu/display: change pipe policy for DCN 2.0""
  drm/amdgpu: Add memory vendor information
  drm/amd: flush any delayed gfxoff on suspend entry
  drm/amdgpu: skip fence GFX interrupts disable/enable for S0ix
  drm/amdgpu: Remove gfxoff check in GFX v9.4.3
  drm/amd/pm: Update pci link speed for smu v13.0.6
  ...

Linux 6.5-rc7

This is needed for the CI stuff and the msm pull has fixes in it.

Signed-off-by: Dave Airlie <airlied@redhat.com>

In case the downstream bridge or panel uses DSI transfers before the
DSI host was actually initialized through samsung_dsim_atomic_enable()
which clears the stop state (LP11) mode, all transfers will fail.

This happens with downstream bridges that are controlled by DSI
commands such as the tc358762.

As documented in [1] DSI hosts are expected to allow transfers
outside the normal bridge enable/disable flow.

To fix this make sure that stop state is cleared in
samsung_dsim_host_transfer() which restores the previous
behavior.

We also factor out the common code to enable/disable stop state
to samsung_dsim_set_stop_state().

[1] https://docs.kernel.org/gpu/drm-kms-helpers.html#mipi-dsi-bridge-operation

Fixes: 0c14d3130654 ("drm: bridge: samsung-dsim: Fix i.MX8M enable flow to meet spec")
Reported-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230724151640.555490-1-frieder@fris.de

The ELD (EDID-Like Data) is not updated when the HDMI cable
is plugged into different HDMI monitors.
This is because the EDID is not updated in the HDMI HPD function.
As a result, the ELD data remains unchanged and may not reflect
the capabilities of the newly connected HDMI sink device.

To address this issue, the handle_plugged_change function should move to
the bridge_atomic_enable and bridge_atomic_disable functions.
Make sure the EDID is properly updated before updating ELD.

Signed-off-by: Sandor Yu <Sandor.yu@nxp.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230804061145.2824843-1-Sandor.yu@nxp.com

This reverts commit 8ddce13ae696 ("drm/bridge: lt9611: Do not generate
HFP/HBP/HSA and EOT packet") to fix display regression on the Dragonboard
845c (SDM845) devboard.

There's a mismatch on the real action of the following flags:
- MIPI_DSI_MODE_VIDEO_NO_HSA
- MIPI_DSI_MODE_VIDEO_NO_HFP
- MIPI_DSI_MODE_VIDEO_NO_HBP
which leads to a non-working display on qcom platforms.

Cc: Marek Vasut <marex@denx.de>
Cc: Robert Foss <rfoss@kernel.org>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Abhinav Kumar <quic_abhinavk@quicinc.com>
Fixes: 8ddce13ae696 ("drm/bridge: lt9611: Do not generate HFP/HBP/HSA and EOT packet")
Reported-by: Amit Pundir <amit.pundir@linaro.org>
Closes: https://lore.kernel.org/r/CAMi1Hd0TD=2z_=bcDrht3H_wiLvAFcv8Z-U_r_KUOoeMc6UMjw@mail.gmail.com/
Tested-by: Amit Pundir <amit.pundir@linaro.org>
Acked-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> #fix db845c
[narmstrong: fixed commit message format]
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230802-revert-do-not-generate-hfp-hbp-hsa-eot-packet-v1-1-f8a20084e15a@linaro.org

On system resume, the driver might call it6505_poweron directly if the
runtime PM hasn't been enabled. In such case, pm_runtime_get_if_in_use
will always return 0 because dev->power.runtime_status stays at
RPM_SUSPENDED, and the IRQ will never be handled.

Use it6505->powered from the driver struct fixes this because it always
gets updated when it6505_poweron is called.

Fixes: 5eb9a4314053 ("drm/bridge: it6505: Guard bridge power in IRQ handler")
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230727100131.2338127-1-treapking@chromium.org

CEC interrupt status/mask and logical address registers
will be reset when device enter suspend.
It will cause cec fail to work after device resume.
Add CEC suspend/resume functions, reinitialize logical address registers
and restore interrupt status/mask registers after resume.

Signed-off-by: Sandor Yu <Sandor.yu@nxp.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230721124415.1513223-1-Sandor.yu@nxp.com

When building with W=1, the following warning occurs.

drivers/gpu/drm/bridge/analogix/analogix-anx78xx.c:48:17: warning: ‘anx781x_i2c_addresses’ defined but not used [-Wunused-const-variable=]  static const u8 anx781x_i2c_addresses[] = {
                 ^~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/bridge/analogix/analogix-anx78xx.c:40:17: warning: ‘anx7808_i2c_addresses’ defined but not used [-Wunused-const-variable=]  static const u8 anx7808_i2c_addresses[] = {

When CONFIG_IO is disabled, above two variables are not used,
since the place where it is used is inclueded in the macro
CONFIG_OF.

Even for drivers that do not depend on CONFIG_OF, it's almost
always better to leave out the of_match_ptr(), since the only
thing it can possibly do is to save a few bytes of .text if a
driver can be used both with and without it. Hence we remove
all of_match_ptr() used in other places.

Fixes: 0647e7dd3f7a ("drm/bridge: Add Analogix anx78xx support")
Signed-off-by: Zhu Wang <wangzhu9@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230731021345.219588-1-wangzhu9@huawei.com

Backmerging to get v6.5-rc2.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>

These two drivers embed a i2c_client in their private driver data, but
only strict device is actually needed. Replace the i2c_client reference
with a struct device one.

Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230718110407.1005200-1-wenst@chromium.org