Update smu v13.0.1 firmware header for yellow carp.

Signed-off-by: Xiaomeng Hou <Xiaomeng.Hou@amd.com>
Reviewed-by: Aaron Liu <aaron.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Correct yellow carp driver-PMFW interface version to v4.

Signed-off-by: Xiaomeng Hou <Xiaomeng.Hou@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Add support for board power calibration on Aldebaran.
Board calibration is done after DC offset calibration.

Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Update the version to 0xD for beige_goby.

Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-by: Jack Gui <Jack.Gui@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Since there's nothing special in smu implementation for yellow carp,
it's better to reuse the common smu_v13_0 interfaces and drop the
specific smu_v13_0_1.c|h files.

v2: remove the duplicate register offset and shift mask header files as
well.

Signed-off-by: Xiaomeng Hou <Xiaomeng.Hou@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Use SMU to update the bad pages rather than directly
accessing the EEPROM from the driver.

Signed-off-by: Stanley.Yang <Stanley.Yang@amd.com>
Reviewed-by: John Clements <john.clements@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

As OOB(out-of-band) interface may be used to update the power limits.
Thus to make sure the power limits reporting of our driver always
reflects the correct values, the internal cache must be aligned
carefully.

V2: add support for out-of-band of other ASICs
    align cached current power limit with OOB imposed

Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-By: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

For some ASICs, the real dpm feature disablement job is handled by
PMFW during baco reset and custom pptable loading. Cached dpm feature
status need to be updated to pair that.

Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Via the fSMC_MSG_ArmD3 message, PMFW can properly act on the
Dstate change. Driver involvement for determining the timing for
BACO enter/exit is not needed.

Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Add new defines for thermal throttle status bits which are ASIC
independent. This bit field will be visible to userspace via
gpu_metrics alongside the previous ASIC dependent bit fields. Seperated
into four types: power throttlers (16 bits), current throttlers (16
bits), temperature (24 bits), other (8 bits).

Signed-off-by: Graham Sider <Graham.Sider@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>