Pull hw lockdown support from David Howells:
 "Annotation of module parameters that configure hardware resources
  including ioports, iomem addresses, irq lines and dma channels.

  This allows a future patch to prohibit the use of such module
  parameters to prevent that hardware from being abused to gain access
  to the running kernel image as part of locking the kernel down under
  UEFI secure boot conditions.

  Annotations are made by changing:

        module_param(n, t, p)
        module_param_named(n, v, t, p)
        module_param_array(n, t, m, p)

  to:

        module_param_hw(n, t, hwtype, p)
        module_param_hw_named(n, v, t, hwtype, p)
        module_param_hw_array(n, t, hwtype, m, p)

  where the module parameter refers to a hardware setting

  hwtype specifies the type of the resource being configured. This can
  be one of:

        ioport          Module parameter configures an I/O port
        iomem           Module parameter configures an I/O mem address
        ioport_or_iomem Module parameter could be either (runtime set)
        irq             Module parameter configures an I/O port
        dma             Module parameter configures a DMA channel
        dma_addr        Module parameter configures a DMA buffer address
        other           Module parameter configures some other value

  Note that the hwtype is compile checked, but not currently stored (the
  lockdown code probably won't require it). It is, however, there for
  future use.

  A bonus is that the hwtype can also be used for grepping.

  The intention is for the kernel to ignore or reject attempts to set
  annotated module parameters if lockdown is enabled. This applies to
  options passed on the boot command line, passed to insmod/modprobe or
  direct twiddling in /sys/module/ parameter files.

  The module initialisation then needs to handle the parameter not being
  set, by (1) giving an error, (2) probing for a value or (3) using a
  reasonable default.

  What I can't do is just reject a module out of hand because it may
  take a hardware setting in the module parameters. Some important
  modules, some ipmi stuff for instance, both probe for hardware and
  allow hardware to be manually specified; if the driver is aborts with
  any error, you don't get any ipmi hardware.

  Further, trying to do this entirely in the module initialisation code
  doesn't protect against sysfs twiddling.

  [!] Note that in and of itself, this series of patches should have no
      effect on the the size of the kernel or code execution - that is
      left to a patch in the next series to effect. It does mark
      annotated kernel parameters with a KERNEL_PARAM_FL_HWPARAM flag in
      an already existing field"

* tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs: (38 commits)
  Annotate hardware config module parameters in sound/pci/
  Annotate hardware config module parameters in sound/oss/
  Annotate hardware config module parameters in sound/isa/
  Annotate hardware config module parameters in sound/drivers/
  Annotate hardware config module parameters in fs/pstore/
  Annotate hardware config module parameters in drivers/watchdog/
  Annotate hardware config module parameters in drivers/video/
  Annotate hardware config module parameters in drivers/tty/
  Annotate hardware config module parameters in drivers/staging/vme/
  Annotate hardware config module parameters in drivers/staging/speakup/
  Annotate hardware config module parameters in drivers/staging/media/
  Annotate hardware config module parameters in drivers/scsi/
  Annotate hardware config module parameters in drivers/pcmcia/
  Annotate hardware config module parameters in drivers/pci/hotplug/
  Annotate hardware config module parameters in drivers/parport/
  Annotate hardware config module parameters in drivers/net/wireless/
  Annotate hardware config module parameters in drivers/net/wan/
  Annotate hardware config module parameters in drivers/net/irda/
  Annotate hardware config module parameters in drivers/net/hamradio/
  Annotate hardware config module parameters in drivers/net/ethernet/
  ...

Pull char/misc driver updates from Greg KH:
 "Here is the big set of new char/misc driver drivers and features for
  4.12-rc1.

  There's lots of new drivers added this time around, new firmware
  drivers from Google, more auxdisplay drivers, extcon drivers, fpga
  drivers, and a bunch of other driver updates. Nothing major, except if
  you happen to have the hardware for these drivers, and then you will
  be happy :)

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'char-misc-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (136 commits)
  firmware: google memconsole: Fix return value check in platform_memconsole_init()
  firmware: Google VPD: Fix return value check in vpd_platform_init()
  goldfish_pipe: fix build warning about using too much stack.
  goldfish_pipe: An implementation of more parallel pipe
  fpga fr br: update supported version numbers
  fpga: region: release FPGA region reference in error path
  fpga altera-hps2fpga: disable/unprepare clock on error in alt_fpga_bridge_probe()
  mei: drop the TODO from samples
  firmware: Google VPD sysfs driver
  firmware: Google VPD: import lib_vpd source files
  misc: lkdtm: Add volatile to intentional NULL pointer reference
  eeprom: idt_89hpesx: Add OF device ID table
  misc: ds1682: Add OF device ID table
  misc: tsl2550: Add OF device ID table
  w1: Remove unneeded use of assert() and remove w1_log.h
  w1: Use kernel common min() implementation
  uio_mf624: Align memory regions to page size and set correct offsets
  uio_mf624: Refactor memory info initialization
  uio: Allow handling of non page-aligned memory regions
  hangcheck-timer: Fix typo in comment
  ...

Pull GPIO updates from Linus Walleij:
 "This is the bulk of GPIO changes for the v4.12 kernel cycle.

  Core changes:

   - Return NULL from gpiod_get_optional() when GPIOLIB is disabled.
     This was a much discussed change. It affects use cases where people
     write drivers that might or might not be using GPIO resources. I
     have decided that this is the lesser evil right now.

   - Make gpiod_count() behave consistently across different hardware
     descriptions.

   - Fix the syntax around open drain/open source to not infer active
     high/low semantics.

  New drivers:

   - A new single-register fixed-direction framework driver for hardware
     that have lines controlled by a single register that just work in
     one direction (out or in), including IRQ support.

   - Support the Fintek F71889A GPIO SuperIO controller.

   - Support the National NI 169445 MMIO GPIO.

   - Support for the X-Gene derivative of the DWC GPIO controller

   - Support for the Rohm BD9571MWV-M PMIC GPIO controller.

   - Refactor the Gemini GPIO driver to a generic Faraday FTGPIO driver
     and replace both the Gemini and the Moxa ART custom drivers with
     this driver.

  Driver improvements:

   - A whole slew of drivers have their spinlocks chaned to raw
     spinlocks as they provide irqchips, and thus we are progressing on
     realtime compliance.

   - Use devm_irq_alloc_descs() in a slew of drivers, getting managed
     resources.

   - Support for the embedded PWM controller inside the MVEBU driver.

   - Debounce, open source and open drain support for the Aspeed driver.

   - Misc smaller fixes like spelling and syntax and whatnot"

* tag 'gpio-v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (77 commits)
  gpio: f7188x: Add a missing break
  gpio: omap: return error if requested debounce time is not possible
  gpio: Add ROHM BD9571MWV-M PMIC GPIO driver
  gpio: gpio-wcove: fix GPIO IRQ status mask
  gpio: DT bindings, move tca9554 from pcf857x to pca953x
  gpio: move tca9554 from pcf857x to pca953x
  gpio: arizona: Correct check whether the pin is an input
  gpio: Add XRA1403 DTS binding documentation
  dt-bindings: add exar to vendor prefixes list
  gpio: gpio-wcove: fix irq pending status bit width
  gpio: dwapb: use dwapb_read instead of readl_relaxed
  gpio: aspeed: Add open-source and open-drain support
  gpio: aspeed: Add debounce support
  gpio: aspeed: dt: Add optional clocks property
  gpio: aspeed: dt: Fix description alignment in bindings document
  gpio: mvebu: Add limited PWM support
  gpio: Use unsigned int for interrupt numbers
  gpio: f7188x: Add F71889A GPIO support.
  gpio: core: Decouple open drain/source flag with active low/high
  gpio: arizona: Correct handling for reading input GPIOs
  ...

Pull MFD updates from Lee Jones:
 "New Drivers:
   - Freescale MXS Low Resolution ADC
   - Freescale i.MX23/i.MX28 LRADC touchscreen
   - Motorola CPCAP Power Button
   - TI LMU (Lighting Management Unit)
   - Atmel SMC (Static Memory Controller)

  New Device Support:
   - Add support for X-Powers AXP803 to axp20x
   - Add support for Dialog Semi DA9061 to da9062-core
   - Add support for Intel Cougar Mountain to lpc_ich
   - Add support for Intel Gemini Lake to lpc_ich

  New Functionality:
   - Add Device Tree support; wm831x-*, axp20x, ti-lmu, da9062, sun4i-gpadc
   - Add IRQ sense support; motorola-cpcap
   - Add ACPI support; cros_ec
   - Add Reset support; altera-a10sr
   - Add ADC support; axp20x
   - Add AC Power support; axp20x
   - Add Runtime PM support; atmel-ebi, exynos-lpass
   - Add Battery Power Supply support; axp20x
   - Add Clock support; exynos-lpass, hi655x-pmic

  Fix-ups:
   - Implicitly specify required headers; motorola-cpcap, intel_soc_pmic_bxtwc
   - Add .remove() method; stm32-timers, exynos-lpass
   - Remove unused code; intel_soc_pmic_core, intel-lpss-acpi, ipaq-micro, atmel-smc, menelaus
   - Rename variables for clarity; axp20x
   - Convert pr_warning() to pr_warn(); db8500-prcmu, sta2x11-mfd, twl4030-power
   - Improve formatting; arizona-core, axp20x
   - Use raw_spinlock_*() variants; asic3, t7l66xb, tc6393xb
   - Simplify/refactor code; arizona-core, atmel-ebi
   - Improve error checking; intel_soc_pmic_core

  Bug Fixes:
   - Ensure OMAP3630/3730 boards can successfully reboot; twl4030-power
   - Correct max-register value; stm32-timers
   - Extend timeout to account for clock stretching; cros_ec_spi
   - Use correct IRQ trigger type; motorola-cpcap
   - Fix bad use of IRQ sense register; motorola-cpcap
   - Logic error "||" should be "&&"; mxs-lradc-ts"

* tag 'mfd-next-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (79 commits)
  input: touchscreen: mxs-lradc: || vs && typos
  dt-bindings: Add AXP803's regulator info
  mfd: axp20x: Support AXP803 variant
  dt-bindings: Add device tree binding for X-Powers AXP803 PMIC
  dt-bindings: Make AXP20X compatible strings one per line
  mfd: intel_soc_pmic_core: Fix unchecked return value
  mfd: menelaus: Remove obsolete local_irq_disable() and local_irq_enable()
  mfd: omap-usb-tll: Configure ULPIAUTOIDLE
  mfd: omap-usb-tll: Fix inverted bit use for USB TLL mode
  mfd: palmas: Fixed spelling mistake in error message
  mfd: lpc_ich: Add support for Intel Gemini Lake SoC
  mfd: hi655x: Add the clock cell to provide WiFi and Bluetooth
  mfd: intel_soc_pmic: Fix a mess with compilation units
  mfd: exynos-lpass: Add runtime PM support
  mfd: exynos-lpass: Add missing remove() function
  mfd: exynos-lpass: Add support for clocks
  mfd: exynos-lpass: Remove pad retention control
  iio: adc: add support for X-Powers AXP20X and AXP22X PMICs ADCs
  mfd: cpcap: Fix bad use of IRQ sense register
  mfd: cpcap: Use ack_invert interrupts
  ...

A break statement was obviously intended here.

Fixes: d69843e416d3 ("gpio: f7188x: Add F71889A GPIO support.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

omap_gpio_debounce() does not validate that the requested debounce
is within a range it can handle. Instead it lets the register value
wrap silently, and always returns success.

This can lead to all sorts of unexpected behavior, such as gpio_keys
asking for a too-long debounce, but getting a very short debounce in
practice.

Fix this by returning -EINVAL if the requested value does not fit into
the register field. If there is no debounce clock available at all,
return -ENOTSUPP.

Fixes: e85ec6c3047b ("gpio: omap: fix omap2_set_gpio_debounce")
Cc: <stable@vger.kernel.org> # 4.3+
Signed-off-by: David Rivshin <drivshin@allworx.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add driver for the GPIO block in the ROHM BD9571MWV-W MFD PMIC.
This block is pretty trivial and supports setting GPIO direction
as Input/Output and in case of Output, supports setting value.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: linux-gpio@vger.kernel.org
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

According to Whiskey Cove PMIC spec, bit 7 of GPIOIRQ0_REG belongs to
battery IO. So we should skip this bit when checking for GPIO IRQ pending
status. Otherwise, wcove_gpio_irq_handler() might go into the infinite
loop until IRQ "pending" status becomes 0. This patch fixes this issue.

Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Crystal Cove and Whiskey Cove are two different PMICs which are
installed on Intel Atom SoC based platforms.

Moreover there are two independent drivers that by some reason were
supposed (*) to get into one kernel module.

Fix the mess by clarifying Kconfig option for Crystal Cove and split
Whiskey Cove out of it.

(*) It looks like the configuration was never tested with
    INTEL_SOC_PMIC=n. The line in Makefile is actually wrong.

Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net> (supporter:ACPI)
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The TCA9554 doesn't work with the pcf857x driver, trying to change the direction
gives a NAK bailout error.

TCA9554 is similar to the PCA9554, thus change the driver.

Signed-off-by: Anders Darander <anders@chargestorm.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>