The mach-nomadik machine did not compile properly due to bad
ux500-specific functions being called. Introduce new state
variables to fix this up.

Reported-by: Axel Lin <axel.lin@gmail.com>
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: Prafulla Wadaskar <prafulla.wadaskar@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

The Samsung GPIO drivers are always built-in when the relevant
platform is selected.  Change the Kconfig symbol to def_bool y
dependant on the platform.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

The S3C_GPIO_PULL_UP macro value incorrectly maps to a reserved setting of GPIO
pull up/down registers on Exynos4 platform. Fix this incorrect mapping by adding
wrappers to the s3c_gpio_setpull_updown and s3c_gpio_getpull_updown functions.

Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

_set_gpio_triggering uses read-modify-write on bank registers,
lock bank->lock around all calls to it to prevent register
corruption if two cpus access gpios in the same bank at the
same time.

Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Setting the IRQWAKEN bit was overwriting previous IRQWAKEN bits,
causing only the last bit set to take effect, resulting in lost
wakeups when the GPIO controller is in idle.

Replace direct writes to IRQWAKEN with MOD_REG_BIT calls to
perform a read-modify-write on the register.

Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

WARNING: arch/arm/plat-omap/built-in.o(.devinit.text+0x46c): Section mismatch in reference from the function omap_gpio_probe() to the function .init.text:omap_gpio_chip_init()
The function __devinit omap_gpio_probe() references
a function __init omap_gpio_chip_init().
If omap_gpio_chip_init is only used by omap_gpio_probe then
annotate omap_gpio_chip_init with a matching annotation.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Kevin Hilman <khilman@ti.com>

After the GPIO driver move, some symbols became selectable when they
shouldn't be.  Tighten the dependencies.

Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

We had a few drivers move from arch/arm into drivers/gpio, but they
don't actually compile without the ARM platform headers etc.  As a
result they were messing up allyesconfig on x86.

Make them depend on ARM.

Reported-by: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'gpio/next' of git://git.secretlab.ca/git/linux-2.6:
  gpio/pch_gpio: Support new device ML7223
  gpio: make gpio_{request,free}_array gpio array parameter const
  GPIO: OMAP: move to drivers/gpio
  GPIO: OMAP: move register offset defines into <plat/gpio.h>
  gpio: Convert gpio_is_valid to return bool
  gpio: Move the s5pc100 GPIO to drivers/gpio
  gpio: Move the s5pv210 GPIO to drivers/gpio
  gpio: Move the exynos4 GPIO to drivers/gpio
  gpio: Move to Samsung common GPIO library to drivers/gpio
  gpio/nomadik: add function to read GPIO pull down status
  gpio/nomadik: show all pins in debug
  gpio: move Nomadik GPIO driver to drivers/gpio
  gpio: move U300 GPIO driver to drivers/gpio
  langwell_gpio: add runtime pm support
  gpio/pca953x: Add support for pca9574 and pca9575 devices
  gpio/cs5535: Show explicit dependency between gpio_cs5535 and mfd_cs5535