linux.git/drivers/gpio/Kconfig, branch v6.9

Merge tag 'pinctrl-v6.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl

2024-03-14T17:22:26+00:00

Pull pin control updates from Linus Walleij:
 "No core changes this time around.

  New drivers:

   - New driver for Renesas R8A779H0 also known as R-Car V4M.

   - New driver for the Awinic AW9523/B I2C GPIO expander. I found this
     living out-of-tree in OpenWrt as an upstream attempt had stalled on
     the finishing line, so I picked it up and finished the job.

  Improvements:

   - The Nomadik pin control driver was for years re-used out of tree
     for the ST STA chips, and now the IP was re-used in a MIPS
     automotive SoC called MobilEyeq5, so it has been split in pin
     control and GPIO drivers so the latter can be reused by MobilEyeq5.
     (Along with a long list of cleanups)

   - A lot of overall cleanup and tidying up"

* tag 'pinctrl-v6.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (87 commits)
  drivers/gpio/nomadik: move dummy nmk_gpio_dbg_show_one() to header
  gpio: nomadik: remove BUG_ON() in nmk_gpio_populate_chip()
  dt-bindings: pinctrl: qcom: update compatible name for match with driver
  pinctrl: aw9523: Make the driver tristate
  pinctrl: nomadik: fix dereference of error pointer
  gpio: nomadik: Back out some managed resources
  pinctrl: aw9523: Add proper terminator
  pinctrl: core: comment that pinctrl_add_gpio_range() is deprecated
  pinctrl: pinmux: Suppress error message for -EPROBE_DEFER
  pinctrl: Add driver for Awinic AW9523/B I2C GPIO Expander
  dt-bindings: pinctrl: Add bindings for Awinic AW9523/AW9523B
  gpio: nomadik: Finish conversion to use firmware node APIs
  gpio: nomadik: fix Kconfig dependencies inbetween pinctrl & GPIO
  pinctrl: da9062: Add OF table
  dt-bindings: pinctrl: at91: add sam9x7
  pinctrl: ocelot: remove redundant assignment to variable ret
  gpio: nomadik: grab optional reset control and deassert it at probe
  gpio: nomadik: support mobileye,eyeq5-gpio
  gpio: nomadik: handle variadic GPIO count
  gpio: nomadik: support shared GPIO IRQs
  ...

gpio: nomadik: Finish conversion to use firmware node APIs

2024-03-03T08:43:10+00:00

Previously driver got a few updates in order to replace OF APIs by
respective firmware node, however it was not finished to the logical
end, e.g., some APIs that has been used are still require OF node
to be passed. Finish that job by converting leftovers to use firmware
node APIs.

Signed-off-by: Andy Shevchenko 
Link: https://lore.kernel.org/r/20240302173401.217830-1-andy.shevchenko@gmail.com
Signed-off-by: Linus Walleij

gpio: nomadik: fix Kconfig dependencies inbetween pinctrl & GPIO

2024-03-01T13:30:28+00:00

PINCTRL_NOMADIK cannot select GPIO_NOMADIK without first selecting
GPIOLIB on which GPIO_NOMADIK depends. GPIO_NOMADIK depends on OF_GPIO,
it is a direct dependency.

Reported-by: kernel test robot 
Closes: https://lore.kernel.org/oe-kbuild-all/202403010917.pnDhdS1Y-lkp@intel.com/
Closes: https://lore.kernel.org/oe-kbuild-all/202403011102.v8w2zPOU-lkp@intel.com/
Closes: https://lore.kernel.org/oe-kbuild-all/202403011329.1VnABMRz-lkp@intel.com/
Closes: https://lore.kernel.org/oe-kbuild-all/202403011546.Hpt8sBTa-lkp@intel.com/
Signed-off-by: Théo Lebrun 
Link: https://lore.kernel.org/r/20240301-mbly-gpio-kconfig-fix-v1-1-2785cebd475d@bootlin.com
Signed-off-by: Linus Walleij

gpio: nomadik: support mobileye,eyeq5-gpio

2024-02-29T09:36:55+00:00

We create a custom compatible for the STA2X11 IP block as integrated
into the Mobileye EyeQ5 platform. Its wake and alternate functions have
been disabled, we want to avoid touching those registers.

We both do: (1) early return in functions that do not support the
platform, but with warnings, and (2) avoid calling those functions in
the first place.

We ensure that pinctrl-nomadik is not used with this STA2X11 variant.

Reviewed-by: Linus Walleij 
Signed-off-by: Théo Lebrun 
Link: https://lore.kernel.org/r/20240228-mbly-gpio-v2-24-3ba757474006@bootlin.com
Signed-off-by: Linus Walleij

gpio: nomadik: extract GPIO platform driver from drivers/pinctrl/nomadik/

2024-02-29T09:22:33+00:00

Previously, drivers/pinctrl/nomadik/pinctrl-nomadik.c registered two
platform drivers: pinctrl & GPIO. Move the GPIO aspect to the
drivers/gpio/ folder, as would be expected.

Both drivers are intertwined for a reason; pinctrl requires access to
GPIO registers for pinmuxing, pull-disable, disabling interrupts while
setting the muxing and wakeup control. Information sharing is done
through a shared array containing GPIO chips and a few helper
functions. That shared array is not touched from gpio-nomadik when
CONFIG_PINCTRL_NOMADIK is not defined.

Make no change to the code that moved into gpio-nomadik; there should be
no behavior change following. A few functions are shared and header
comments are added. Checkpatch warnings are addressed. NUM_BANKS is
renamed to NMK_MAX_BANKS.

It is supported to compile gpio-nomadik without pinctrl-nomadik. The
opposite is not true.

Signed-off-by: Théo Lebrun 
Link: https://lore.kernel.org/r/20240228-mbly-gpio-v2-6-3ba757474006@bootlin.com
Signed-off-by: Linus Walleij

gpio: Add ChromeOS EC GPIO driver

2024-02-26T13:37:50+00:00

The ChromeOS embedded controller (EC) supports setting the state of
GPIOs when the system is unlocked, and getting the state of GPIOs in all
cases. The GPIOs are on the EC itself, so the EC acts similar to a GPIO
expander. Add a driver to get and set the GPIOs on the EC through the
host command interface.

Signed-off-by: Stephen Boyd 
Reviewed-by: Linus Walleij 
Signed-off-by: Bartosz Golaszewski

gpio: vf610: enable COMPILE_TEST

2024-02-02T13:32:12+00:00

Enable COMPILE_TEST for the vf610 gpio driver to support test builds on
systems without this hardware.

Signed-off-by: Martin Kaiser 
Signed-off-by: Bartosz Golaszewski

gpio: vf610: allow disabling the vf610 driver

2024-02-02T13:32:03+00:00

The vf610 gpio driver is enabled by default for all i.MX machines,
without any option to disable it in a board-specific config file.

Most i.MX chipsets have no hardware for this driver. Change the default
to enable GPIO_VF610 for SOC_VF610 and disable it otherwise.

Add a text description after the bool type, this makes the driver
selectable by make config etc.

Fixes: 30a35c07d9e9 ("gpio: vf610: drop the SOC_VF610 dependency for GPIO_VF610")
Signed-off-by: Martin Kaiser 
Signed-off-by: Bartosz Golaszewski

gpio: nuvoton: Add Nuvoton NPCM sgpio driver

2024-01-03T10:25:41+00:00

Add Nuvoton BMC NPCM7xx/NPCM8xx sgpio driver support.
Nuvoton NPCM SGPIO module is combine serial to parallel IC (HC595)
and parallel to serial IC (HC165), and use APB3 clock to control it.
This interface has 4 pins  (D_out , D_in, S_CLK, LDSH).
BMC can use this driver to increase 64 GPI pins and 64 GPO pins to use.

Signed-off-by: Jim Liu 
Signed-off-by: Bartosz Golaszewski

gpio: rtd: Add support for Realtek DHC(Digital Home Center) RTD SoCs

2024-01-03T09:46:21+00:00

This driver enables configuration of GPIO direction, GPIO values, GPIO
debounce settings and handles GPIO interrupts.

Signed-off-by: Tzuyi Chang 
Reviewed-by: Linus Walleij 
Signed-off-by: Bartosz Golaszewski