linux.git/drivers/gpio/Kconfig, branch v4.12 Linux kernel source tree Merge tag 'gpio-v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio 2017-05-04T19:05:32+00:00 Linus Torvalds torvalds@linux-foundation.org 2017-05-04T19:05:32+00:00 2bd80401743568ced7d303b008ae5298ce77e695 Pull GPIO updates from Linus Walleij: "This is the bulk of GPIO changes for the v4.12 kernel cycle. Core changes: - Return NULL from gpiod_get_optional() when GPIOLIB is disabled. This was a much discussed change. It affects use cases where people write drivers that might or might not be using GPIO resources. I have decided that this is the lesser evil right now. - Make gpiod_count() behave consistently across different hardware descriptions. - Fix the syntax around open drain/open source to not infer active high/low semantics. New drivers: - A new single-register fixed-direction framework driver for hardware that have lines controlled by a single register that just work in one direction (out or in), including IRQ support. - Support the Fintek F71889A GPIO SuperIO controller. - Support the National NI 169445 MMIO GPIO. - Support for the X-Gene derivative of the DWC GPIO controller - Support for the Rohm BD9571MWV-M PMIC GPIO controller. - Refactor the Gemini GPIO driver to a generic Faraday FTGPIO driver and replace both the Gemini and the Moxa ART custom drivers with this driver. Driver improvements: - A whole slew of drivers have their spinlocks chaned to raw spinlocks as they provide irqchips, and thus we are progressing on realtime compliance. - Use devm_irq_alloc_descs() in a slew of drivers, getting managed resources. - Support for the embedded PWM controller inside the MVEBU driver. - Debounce, open source and open drain support for the Aspeed driver. - Misc smaller fixes like spelling and syntax and whatnot" * tag 'gpio-v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (77 commits) gpio: f7188x: Add a missing break gpio: omap: return error if requested debounce time is not possible gpio: Add ROHM BD9571MWV-M PMIC GPIO driver gpio: gpio-wcove: fix GPIO IRQ status mask gpio: DT bindings, move tca9554 from pcf857x to pca953x gpio: move tca9554 from pcf857x to pca953x gpio: arizona: Correct check whether the pin is an input gpio: Add XRA1403 DTS binding documentation dt-bindings: add exar to vendor prefixes list gpio: gpio-wcove: fix irq pending status bit width gpio: dwapb: use dwapb_read instead of readl_relaxed gpio: aspeed: Add open-source and open-drain support gpio: aspeed: Add debounce support gpio: aspeed: dt: Add optional clocks property gpio: aspeed: dt: Fix description alignment in bindings document gpio: mvebu: Add limited PWM support gpio: Use unsigned int for interrupt numbers gpio: f7188x: Add F71889A GPIO support. gpio: core: Decouple open drain/source flag with active low/high gpio: arizona: Correct handling for reading input GPIOs ... 
Pull GPIO updates from Linus Walleij:
 "This is the bulk of GPIO changes for the v4.12 kernel cycle.

  Core changes:

   - Return NULL from gpiod_get_optional() when GPIOLIB is disabled.
     This was a much discussed change. It affects use cases where people
     write drivers that might or might not be using GPIO resources. I
     have decided that this is the lesser evil right now.

   - Make gpiod_count() behave consistently across different hardware
     descriptions.

   - Fix the syntax around open drain/open source to not infer active
     high/low semantics.

  New drivers:

   - A new single-register fixed-direction framework driver for hardware
     that have lines controlled by a single register that just work in
     one direction (out or in), including IRQ support.

   - Support the Fintek F71889A GPIO SuperIO controller.

   - Support the National NI 169445 MMIO GPIO.

   - Support for the X-Gene derivative of the DWC GPIO controller

   - Support for the Rohm BD9571MWV-M PMIC GPIO controller.

   - Refactor the Gemini GPIO driver to a generic Faraday FTGPIO driver
     and replace both the Gemini and the Moxa ART custom drivers with
     this driver.

  Driver improvements:

   - A whole slew of drivers have their spinlocks chaned to raw
     spinlocks as they provide irqchips, and thus we are progressing on
     realtime compliance.

   - Use devm_irq_alloc_descs() in a slew of drivers, getting managed
     resources.

   - Support for the embedded PWM controller inside the MVEBU driver.

   - Debounce, open source and open drain support for the Aspeed driver.

   - Misc smaller fixes like spelling and syntax and whatnot"

* tag 'gpio-v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (77 commits)
  gpio: f7188x: Add a missing break
  gpio: omap: return error if requested debounce time is not possible
  gpio: Add ROHM BD9571MWV-M PMIC GPIO driver
  gpio: gpio-wcove: fix GPIO IRQ status mask
  gpio: DT bindings, move tca9554 from pcf857x to pca953x
  gpio: move tca9554 from pcf857x to pca953x
  gpio: arizona: Correct check whether the pin is an input
  gpio: Add XRA1403 DTS binding documentation
  dt-bindings: add exar to vendor prefixes list
  gpio: gpio-wcove: fix irq pending status bit width
  gpio: dwapb: use dwapb_read instead of readl_relaxed
  gpio: aspeed: Add open-source and open-drain support
  gpio: aspeed: Add debounce support
  gpio: aspeed: dt: Add optional clocks property
  gpio: aspeed: dt: Fix description alignment in bindings document
  gpio: mvebu: Add limited PWM support
  gpio: Use unsigned int for interrupt numbers
  gpio: f7188x: Add F71889A GPIO support.
  gpio: core: Decouple open drain/source flag with active low/high
  gpio: arizona: Correct handling for reading input GPIOs
  ...
gpio: Add ROHM BD9571MWV-M PMIC GPIO driver 2017-04-28T07:47:46+00:00 Marek Vasut marek.vasut@gmail.com 2017-04-25T18:32:09+00:00 9384793036afb7529c1c564e839ef4356271d68e Add driver for the GPIO block in the ROHM BD9571MWV-W MFD PMIC. This block is pretty trivial and supports setting GPIO direction as Input/Output and in case of Output, supports setting value. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: linux-gpio@vger.kernel.org Cc: Geert Uytterhoeven <geert+renesas@glider.be> Cc: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> 
Add driver for the GPIO block in the ROHM BD9571MWV-W MFD PMIC.
This block is pretty trivial and supports setting GPIO direction
as Input/Output and in case of Output, supports setting value.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: linux-gpio@vger.kernel.org
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
mfd: intel_soc_pmic: Fix a mess with compilation units 2017-04-27T10:54:42+00:00 Andy Shevchenko andriy.shevchenko@linux.intel.com 2017-04-04T12:38:56+00:00 b5238b41858229b2dcb684cd71d81f4c6d6311c0 Crystal Cove and Whiskey Cove are two different PMICs which are installed on Intel Atom SoC based platforms. Moreover there are two independent drivers that by some reason were supposed (*) to get into one kernel module. Fix the mess by clarifying Kconfig option for Crystal Cove and split Whiskey Cove out of it. (*) It looks like the configuration was never tested with INTEL_SOC_PMIC=n. The line in Makefile is actually wrong. Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net> (supporter:ACPI) Acked-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> 
Crystal Cove and Whiskey Cove are two different PMICs which are
installed on Intel Atom SoC based platforms.

Moreover there are two independent drivers that by some reason were
supposed (*) to get into one kernel module.

Fix the mess by clarifying Kconfig option for Crystal Cove and split
Whiskey Cove out of it.

(*) It looks like the configuration was never tested with
    INTEL_SOC_PMIC=n. The line in Makefile is actually wrong.

Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net> (supporter:ACPI)
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
gpio: move tca9554 from pcf857x to pca953x 2017-04-24T16:27:55+00:00 Anders Darander anders@chargestorm.se 2017-04-21T12:46:30+00:00 1b9a0c25065c174134494d1ca91f4da8430e6902 The TCA9554 doesn't work with the pcf857x driver, trying to change the direction gives a NAK bailout error. TCA9554 is similar to the PCA9554, thus change the driver. Signed-off-by: Anders Darander <anders@chargestorm.se> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> 
The TCA9554 doesn't work with the pcf857x driver, trying to change the direction
gives a NAK bailout error.

TCA9554 is similar to the PCA9554, thus change the driver.

Signed-off-by: Anders Darander <anders@chargestorm.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpio: add generic single-register fixed-direction GPIO driver 2017-03-24T13:04:46+00:00 Russell King rmk+kernel@armlinux.org.uk 2016-08-31T07:49:44+00:00 380639c7cc786ec663e43eb3896ccf9172a46900 Add a simple, generic, single register fixed-direction GPIO driver. This is able to support a single register with a mixture of inputs and outputs. This is different from gpio-mmio and gpio-74xx-mmio: * gpio-mmio doesn't allow a fixed direction, it assumes there is always a direction register. * gpio-74xx-mmio only supports all-in or all-out setups * gpio-74xx-mmio is DT only, this needs to support legacy too * they don't double-read when getting the GPIO value, as required by some implementations that this driver supports * we need to always do 32-bit reads, which bgpio doesn't guarantee * the current output state may not be readable from the hardware register - reading may reflect input status but not output status. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> 
Add a simple, generic, single register fixed-direction GPIO driver.
This is able to support a single register with a mixture of inputs
and outputs.

This is different from gpio-mmio and gpio-74xx-mmio:
* gpio-mmio doesn't allow a fixed direction, it assumes there is always
  a direction register.
* gpio-74xx-mmio only supports all-in or all-out setups
* gpio-74xx-mmio is DT only, this needs to support legacy too
* they don't double-read when getting the GPIO value, as required by
  some implementations that this driver supports
* we need to always do 32-bit reads, which bgpio doesn't guarantee
* the current output state may not be readable from the hardware
  register - reading may reflect input status but not output status.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpio: moxart: Switch to using the FTGPIO010 driver 2017-03-22T08:45:02+00:00 Linus Walleij linus.walleij@linaro.org 2017-03-12T23:28:17+00:00 d8307c09206b35a9526bfdf076c9f516c0b5e6f1 This just deletes the Moxa ART driver and replaces it with the more versatile Faraday FTGPIO010 driver. Make this default on for ARCH_GEMINI and ARCH_MOXART so we do not get Kconfig glitches. Tested-by: Jonas Jensen <jonas.jensen@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> 
This just deletes the Moxa ART driver and replaces it with the
more versatile Faraday FTGPIO010 driver.

Make this default on for ARCH_GEMINI and ARCH_MOXART so we do
not get Kconfig glitches.

Tested-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpio: gemini: rename to match Faraday IP 2017-03-22T08:40:55+00:00 Linus Walleij linus.walleij@linaro.org 2017-03-12T23:28:16+00:00 9d3a15aaaec41252ad7c6592305264e52a801be7 The Gemini driver is actually a driver for the Faraday Technology FTGPIO010 IP block. We rename the driver and the Kconfig symbol and put in a a new compatible string for the Moxa ART SoC that is also using this IP block. Tested-by: Jonas Jensen <jonas.jensen@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> 
The Gemini driver is actually a driver for the Faraday Technology
FTGPIO010 IP block. We rename the driver and the Kconfig symbol and
put in a a new compatible string for the Moxa ART SoC that is also
using this IP block.

Tested-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpio: xlp: Update for ARCH_THUNDER2 2017-03-16T20:52:10+00:00 Jayachandran C jnair@caviumnetworks.com 2017-03-12T11:14:28+00:00 529f75d8ca214aa52ed609d1a909bbe3a71504bf ARCH_VULCAN arm64 platform (for Broadcom Vulcan ARM64 processors) has been discontinued. Cavium's ThunderX2 CN99XX (ARCH_THUNDER2) will be the next revision of this platform. Update compile dependencies and ACPI ID to reflect this change. Signed-off-by: Jayachandran C <jnair@caviumnetworks.com> [Drop depreciation of ARCH_VULCAN] Signed-off-by: Linus Walleij <linus.walleij@linaro.org> 
ARCH_VULCAN arm64 platform (for Broadcom Vulcan ARM64 processors) has
been discontinued. Cavium's ThunderX2 CN99XX (ARCH_THUNDER2) will be
the next revision of this platform.

Update compile dependencies and ACPI ID to reflect this change.

Signed-off-by: Jayachandran C <jnair@caviumnetworks.com>
[Drop depreciation of ARCH_VULCAN]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpio: pc104: Mask PC/104 drivers via PC104 Kconfig option 2017-03-15T10:16:38+00:00 William Breathitt Gray vilhelm.gray@gmail.com 2017-01-10T18:51:06+00:00 660549e05d6bf7ed7160de51da2948c2f1646f7e PC/104 drivers should be hidden on machines which do not support PC/104 devices. This patch adds the PC104 Kconfig option as a dependency for the relevant PC/104 device driver Kconfig options. Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Alexandre Courbot <gnurou@gmail.com> Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> 
PC/104 drivers should be hidden on machines which do not support PC/104
devices. This patch adds the PC104 Kconfig option as a dependency for
the relevant PC/104 device driver Kconfig options.

Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpio: mockup: add a dummy irqchip 2017-02-13T07:35:33+00:00 Bartosz Golaszewski bgolaszewski@baylibre.com 2017-02-06T14:11:07+00:00 e2ff7408953f6fe8a341b31ed2d848f73606bbf4 Setup a dummy irqchip that will allow us to inject line events for testing purposes. Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> 
Setup a dummy irqchip that will allow us to inject line events for
testing purposes.

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>